Datalogic Magellan 1100i Quick Reference Manual

Quick Reference Guide ­ Guida Rapida Guide de Référence Rapide Guía de Referencia Rápida Schnellanleitung ­ Referência Rápida ᖿ䗳খ㗗 - クイック·リファレンス

959 Terry Street Eugene, Oregon 97402 Telephone: (541) 683-5700 Fax: (541) 345-7140 An Unpublished Work - All rights reserved. No part of the contents of this documen- tation or the procedures described therein may be reproduced or transmitted in any form or by any means without prior written permission of Datalogic Scanning, Inc. or its subsidiaries or affiliates ("Datalogic" or ““Datalogic Scanning””). Owners of Dat- alogic products are hereby granted a non-exclusive, revocable license to reproduce and transmit this documentation for the purchaser's own internal business pur- poses. Purchaser shall not remove or alter any proprietary notices, including copy- right notices, contained in this documentation and shall ensure that all notices appear on any reproductions of the documentation. Should future revisions of this manual be published, you can acquire printed ver- sions by contacting your Datalogic representative. Electronic versions may either be downloadable from the Datalogic website (www.scanning.datalogic.com) or pro- vided on appropriate media. If you visit our website and would like to make com- ments or suggestions about this or other Datalogic publications, please let us know via the "Contact Datalogic" page. Disclaimer Datalogic has taken reasonable measures to provide information in this manual that is complete and accurate, however, Datalogic reserves the right to change any specification at any time without prior notice. Datalogic is a registered trademark of Datalogic S.p.A. in many countries and the Datalogic logo is a trademark of Datalogic S.p.A. All other brand and product names referred to herein may be trademarks of their respective owners. This product may be covered by one or more of the following patents: 4603262 • 4639606 • 4652750 • 4672215 • 4699447 • 4709369 • 4749879 • 4786798 • 4792666 • 4794240 • 4798943 • 4799164 • 4820911 • 4845349 • 4861972 • 4861973 • 4866257 • 4868836 • 4879456 • 4939355 • 4939356 • 4943127 • 4963719 • 4971176 • 4971177 • 4991692 • 5001406 • 5015831 • 5019697 • 5019698 • 5086879 • 5115120 • 5144118 • 5146463 • 5179270 • 5198649 • 5200597 • 5202784 • 5208449 • 5210397 • 5212371 • 5212372 • 5214270 • 5229590 • 5231293 • 5232185 • 5233169 • 5235168 • 5237161 • 5237162 • 5239165 • 5247161 • 5256864 • 5258604 • 5258699 • 5260554 • 5274219 • 5296689 • 5298728 • 5311000 • 5327451 • 5329103 • 5330370 • 5347113 • 5347121 • 5371361 • 5382783 • 5386105 • 5389917 • 5410108 • 5420410 • 5422472 • 5426507 • 5438187 • 5440110 • 5440111 • 5446271 • 5446749 • 5448050 • 5463211 • 5475206 • 5475207 • 5479011 • 5481098 • 5491328 • 5493108 • 5504350 • 5508505 • 5512740 • 5541397 • 5552593 • 5557095 • 5563402 • 5565668 • 5576531 • 5581707 • 5594231 • 5594441 • 5598070 • 5602376 • 5608201 • 5608399 • 5612529 • 5629510 • 5635699 • 5641958 • 5646391 • 5661435 • 5664231 • 5666045 • 5671374 • 5675138 • 5682028 • 5686716 • 5696370 • 5703347 • 5705802 • 5714750 • 5717194 • 5723852 • 5750976 • 5767502 • 5770847 • 5786581 • 5786585 • 5787103 • 5789732 • 5796222 • 5804809 • 5814803 • 5814804 • 5821721 • 5822343 • 5825009 • 5834708 • 5834750 • 5837983 • 5837988 • 5852286 • 5864129 • 5869827 • 5874722 • 5883370 • 5905249 • 5907147 • 5923023 • 5925868 • 5929421 • 5945670 • 5959284 • 5962838 • 5979769 • 6000619 • 6006991 • 6012639 • 6016135 • 6024284 • 6041374 • 6042012 • 6045044 • 6047889 • 6047894 • 6056198 • 6065676 • 6069696 • 6073849 • 6073851 • 6094288 • 6112993 • 6129279 • 6129282 • 6134039 • 6142376 • 6152368 • 6152372 • 6155488 • 6166375 • 6169614 • 6173894 • 6176429 • 6188500 • 6189784 • 6213397 • 6223986 • 6230975 • 6230976 • 6244510 • 6259545 • 6260763 • 6266175 • 6273336 • 6276605 • 6279829 • 6290134 • 6290135 • 6293467 • 6303927 • 6311895 • 6318634 • 6328216 • 6332576 • 6332577 • 6343741 • 6454168 • 6478224 • 6568598 • 6578765 • 6705527 • 6857567 • 6974084 • 6991169 • 7051940 • 7170414 • 7172123 • 7201322 • 7204422 • 7215493 • 7224540 • 7234641 • 7243850 • 7374092 • 7407096 • 601 26 118.6 • AU703547 • D312631 • D313590 • D320011 • D320012 • D323492 • D330707 • D330708 • D349109 • D350127 • D350735 • D351149 • D351150 • D352936 • D352937 • D352938 • D352939 • D358588 • D361565 • D372234 • D374630 • D374869 • D375493 • D376357 • D377345 • D377346 • D377347 • D377348 • D388075 • D446524 • EP0256296 • EP0260155 • EP0260156 • EP0295936 • EP0325469 • EP0349770 • EP0368254 • EP0442215 • EP0498366 • EP0531645 • EP0663643 • EP0698251 • EP01330772 • GB2252333 • GB2284086 • GB2301691 • GB2304954 • GB2307093 • GB2308267 • GB2308678 • GB2319103 • GB2333163 • GB2343079 • GB2344486 • GB2345568 • GB2354340 • ISR107546 • ISR118507 • ISR118508 • JP1962823 • JP1971216 • JP2513442 • JP2732459 • JP2829331 • JP2953593 • JP2964278 • MEX185552 • MEX187245 • RE37166 • RE40.071 • Other Patents Pending

i Table of Contents English ..........................................................1 Italiano ...........................................................5 Español .........................................................9 Portugues ....................................................13 Francais .......................................................17 Deutsch .......................................................21 Chinese .......................................................25 Japanese .....................................................29

iii DATALOGIC SCANNING, INC. MAGELLAN® END USER LICENSE AGREEMENT Notice to End User: The Datalogic Product you have acquired contains embedded Soft- ware, which is integral to the product's operation. This Software is being provided to you under license, subject to the terms and conditions of this Agreement. If you use the Datalogic Product, you will be deemed to have accepted the terms and conditions of this Agreement. If you do not intend to be bound to the terms of this Agreement, Datalogic is not willing to license the Software to you, you may not use the Datalogic Product or the Software, and you must contact the party from whom you acquired the Datalogic Product for instructions. This End User Software License Agreement ("Agreement") is a legally binding agreement gov- erning the licensing of the Software and Documentation by Datalogic,Scanning Holdings, Inc. and its subsidiaries and affiliates ("Datalogic") to the entity or person who has purchased or oth- erwise acquired a Datalogic Product ("End User"). For purposes of this Agreement, any soft- ware that is associated with a separate end-user license agreement is licensed to you under the terms of that license agreement. Datalogic and End User hereby agree as follows: 1. Definitions. 1.1 "Documentation" means materials such as user's guides, program reference guides, quick reference guides, manuals, or similar materials associated with or related to the Datalogic Product, whether in printed, "online", or other form. 1.2 "Proprietary Information" means: (a) source code, object code, software, documentation, and any related internal design, system design, data base design, algorithms, technol- ogy, technical data or information, implementation techniques, and trade secrets related to the Software, (b) any other trade secrets marked appropriately or identified as proprie- tary or confidential, and (c) any information that End User, under the circumstances, should recognize as confidential. Proprietary Information does not include any informa- tion that the receiving party can establish was (1) in the public domain, (2) already in the receiving party's possession or rightfully known prior to receipt, (3) rightfully learned from a third party not in violation of any other's proprietary rights, or (4) independently devel- oped without access to Proprietary Information. 1.3 "Datalogic Product" means the Datalogic Magellan® 1000i series, Magellan® 1100i series, Magellan® 1400i series, Magellan® 8100 series, Magellan® 8200 series, Magel- lan® 8300 series, Magellan® 8400 series, Magellan® 8500 series, Magellan® 9500 series, and/or Magellan SL® series scanner and/or scanner/scale product, including all embedded Software in and all Documentation related to such product, which has been purchased or otherwise acquired by End User, whether obtained directly or indirectly from Datalogic. 1.4 "Software" means any software or computer programs of Datalogic or its third party licen- sors in machine readable form which is embedded in the Datalogic Product, whether obtained directly or indirectly from Datalogic, including any replacement, update, upgrade, enhancement or modification. 2. Scope Of License Granted. 2.1 Datalogic grants to End User a non-exclusive, non-transferable, perpetual license to use the Software, solely on the Datalogic Product in which it is embedded ("designated Data- logic Product"), in machine-readable form only, solely for End User's internal business purposes. This Agreement does not convey ownership of the Software to End User. Title to the Software shall be and remain with Datalogic or the third party from whom Dat- alogic has obtained a licensed right. As used in this Agreement, the term "purchase" or its equivalents when applied to the Software shall mean "acquire under license." End User is not entitled to receipt or use of the source code to any Software. 2.2 End User shall not copy, modify, decompile, disassemble, reverse engineer, or otherwise reproduce or remanufacture the Software, whether modified or unmodified, nor sell, assign, sublicense, distribute, lend, rent, give, or otherwise transfer the Software to any other person or organization, for purposes other than as expressly provided in this Agreement, without Datalogic's prior written consent.

3.1 Any copying, installing, reproduction, remanufacture, reverse engineering, electronic transfer, or other use of the Software on other than the designated Datalogic Product will be a material breach of this Agreement. However, Datalogic may elect not to terminate this Agreement or the granted licenses, but instead may elect to notify End User that End User is deemed to have ordered and accepted a license for each breaching use. End User shall pay Datalogic the applicable list price for such licenses as of the date of such breach. 3.2 End User shall not sell, assign, sublicense, distribute, lend, rent, give, or otherwise trans- fer the Datalogic Product to any third party unless such third party agrees with Datalogic in writing to be bound by the terms and conditions of this Agreement. Any such transfer of the Datalogic Product absent such agreement shall be null and void. 3.3 End User may obtain support for Software from Datalogic at Datalogic's standard sup- port fees and under Datalogic's standard support terms and conditions in effect at the time the support is requested. 4. Intellectual Property. End User acknowledges that the Software constitutes valuable trade secrets of Datalogic or Datalogic's third party licensors and that the Software is protected by intellectual property laws and treaties. The license set forth in this Agreement does not transfer to End User any owner- ship of Datalogic's or its third party licensors' copyrights, patents, trademarks, service marks, trade secrets, or other intellectual property rights and End User shall have no right to com- mence any legal actions to obtain such rights. End User shall not remove, modify, or take any other action that would obscure any copyright, trademark, patent marking, or other intellectual property notices contained in or on the Datalogic Product. 5. Proprietary Information. 5.1 End User acknowledges that Proprietary Information is the confidential, proprietary, and trade secret property of Datalogic and Datalogic's third party licensors and End User acquires no right or interest in any Proprietary Information. 5.2 End User shall not disclose, provide, or otherwise make available the Proprietary Infor- mation of Datalogic or its third party licensors to any person other than End User's autho- rized employees or agents who are under confidentiality agreement, and End User shall not use the Proprietary Information other than in conjunction with use of the Datalogic Product exclusively for End User's internal business purposes. End User shall take steps to protect the Proprietary Information no less securely than if it were End User's own intellectual property. 5.3 The provisions of this Proprietary Information Section shall survive and continue for five (5) years after the termination of this Agreement. 6. Limited Warranty. 6.1 Datalogic warrants that, under normal use and operation, the Datalogic Product will con- form substantially to the applicable Documentation for the period specified in the Docu- mentation. During this period, for all reproducible nonconformities for which Datalogic has been given written notice, Datalogic will use commercially reasonable efforts to rem- edy nonconformities verified by Datalogic. End User agrees to supply Datalogic with all reasonably requested information and assistance necessary to help Datalogic in reme- dying such nonconformities. For all defects reported to Datalogic within the warranty period, Datalogic's liability is limited to providing End User with one copy of corrections or responding to End User's problem reports according to Datalogic's standard assistance practices. Datalogic does not warrant that the product will meet End User's requirements or that use of the product will be uninterrupted or error free, or that Datalogic's remedial efforts will correct any nonconformance. This limited warranty does not cover any prod- uct that has been subjected to damage or abuse, whether intentionally, accidentally, or by neglect, or to unauthorized repair or unauthorized installation, and shall be void if End User modifies the product, uses the product in any manner other than as established in the Documentation, or if End User breaches any of the provisions of this Agreement. 6.2 EXCEPT AS PROVIDED IN THIS AGREEMENT, THE DATALOGIC PRODUCT IS PRO- VIDED "AS IS" AND DATALOGIC MAKES NO WARRANTIES OF ANY KIND, EXPRESS OR IMPLIED, WRITTEN OR ORAL, WITH RESPECT TO THE PRODUCT, AND SPE- CIFICALLY DISCLAIMS THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE.

v 7. Infringement. 7.1 Datalogic will defend End User against any claim in a lawsuit that the Datalogic Product furnished hereunder infringe a United States patent or copyright of a third party and Dat- alogic will pay any damages finally awarded against End User by a court of competent jurisdiction that are attributable to such claim or will pay End User's part of any settle- ment that is attributable to such claim, provided, that 1) End User notifies Datalogic promptly in writing of the claim, 2) Datalogic controls the defense or settlement of the claim, and 3) End User cooperates fully with Datalogic in such defense or settlement. All notices of a claim should be sent to Datalogic Scanning Holdings, Inc., Legal Depart- ment, 959 Terry Street, Eugene, OR 97402. 7.2 In the defense or settlement of any such claim, Datalogic may, at its option, 1) procure for End User the right to continue using the Datalogic Product, 2) modify the Datalogic Prod- uct so that it becomes non-infringing, 3) replace the Datalogic Product with an equivalent product not subject to such claim, or 4) provide End User an opportunity to return the Datalogic Product and receive a refund of the purchase price paid, less a reasonable allowance for use. 7.3 Datalogic shall have no liability to End User for claims of infringement based upon 1) the use of any Datalogic Product in combination with any product which Datalogic has not either furnished or authorized for use with such Datalogic Product 2) the use of any Dat- alogic Product designed, manufactured, or modified to the specifications of End User, or 3) End User's modification of the Datalogic Product without written authorization from Datalogic. 7.4 THE FOREGOING STATES DATALOGIC'S COMPLETE AND ENTIRE OBLIGATION CONCERNING CLAIMS OF PATENT, COPYRIGHT, OR OTHER INTELLECTUAL PROPERTY INFRINGEMENT, CANCELS AND SUPERSEDES ANY PRIOR AGREE- MENTS, WHETHER ORAL OR WRITTEN, BETWEEN THE PARTIES CONCERNING SUCH CLAIMS, AND WILL NOT BE MODIFIED OR AMENDED BY ANY PAST, CON- TEMPORANEOUS, OR FUTURE AGREEMENTS OR DEALINGS BETWEEN THE PARTIES, WHETHER ORAL OR WRITTEN, EXCEPT AS SET FORTH IN A FUTURE WRITING SIGNED BY BOTH PARTIES. 8. Limitation Of Liability. EXCEPT AS PROVIDED IN SECTION 7, DATALOGIC SHALL NOT BE LIABLE FOR ANY CLAIMS AGAINST END USER BY ANY OTHER PARTY. IN NO EVENT SHALL DATALOGIC'S LIABILITY FOR DAMAGES, IF ANY, WHETHER BASED UPON CONTRACT, TORT (INCLUD- ING NEGLIGENCE), PRODUCT LIABILITY, STRICT LIABILITY, WARRANTY, OR ANY OTHER BASIS, EXCEED THE PRICE OR FEE PAID BY END USER FOR THE DATALOGIC PROD- UCT. UNDER NO CIRCUMSTANCES SHALL DATALOGIC BE LIABLE TO END USER OR ANY THIRD PARTY FOR LOST PROFITS, LOST DATA, INTERRUPTION OF BUSINESS OR SERVICE, OR FOR ANY OTHER SPECIAL, CONSEQUENTIAL, CONTINGENT, INDIRECT, INCIDENTAL, PUNITIVE, EXEMPLARY, OR OTHER SIMILAR DAMAGES, EVEN IF DATA- LOGIC HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. 9. Government Restricted Rights; International Use. 9.1 Use, duplication, or disclosure of the Software by the U.S. Government is subject to the restrictions for computer software developed at private expense as set forth in the U.S. Federal Acquisition Regulations at FAR 52.227-14(g), or 52.227-19 or in the Rights in Technical Data and Computer Software clause at DFARS 252.227-7013(c)(1)(ii), which- ever is applicable. 9.2 If End User is using the Datalogic Product outside of the United States, End User must comply with the applicable local laws of the country in which the Datalogic Product is used, with U.S. export control laws, and with the English language version of this Agree- ment. The provisions of the "United Nations Convention on International Sale of Goods" shall not apply to this Agreement. 10. Termination. 10.1 Either party may terminate this Agreement or any license granted under this Agreement at any time upon written notice if the other party breaches any provision of this Agree- ment. 10.2 Upon termination of this Agreement, End User immediately shall cease using any non- embedded software and shall return to Datalogic or destroy all non-embedded software covered by this Agreement, and shall furnish Datalogic with a certificate of compliance with this provision signed by an officer or authorized representative of End User. For

further use of the embedded Software. End User's resumed or continued use of the embedded Software after termination shall constitute End User's agreement to be bound by the terms and conditions of this Agreement for such use. 11. General Provisions. 11.1 Entire Agreement; Amendment. This document contains the entire agreement between the parties relating to the licensing of the Software and supersedes all prior or contempo- raneous agreements, written or oral, between the parties concerning the licensing of the Software. This Agreement may not be changed, amended, or modified except by written document signed by Datalogic. 11.2 Notice. All notices required or authorized under this Agreement shall be given in writing, and shall be effective when received, with evidence of receipt. Notices to Datalogic shall be sent to the attention of Contract Administration, Datalogic Scanning Holdings, Inc., 959 Terry Street, Eugene, OR 97402, or such other address as may be specified by Dat- alogic in writing. 11.3 Waiver. A party's failure to enforce any of the terms and conditions of this Agreement shall not prevent the party's later enforcement of such terms and conditions. 11.4 Governing Law; Venue: This Agreement and the rights of the parties hereunder shall be governed by and construed in accordance with the laws of the State of Oregon U.S.A, without regard to the rules governing conflicts of law. The state or federal courts of the State of Oregon located in either Multnomah or Lane counties shall have exclusive juris- diction over all matters regarding this Agreement, except that Datalogic shall have the right, at its absolute discretion, to initiate proceedings in the courts of any other state, country, or territory in which End User resides, or in which any of End User's assets are located. 11.5 Attorneys’ Fees. In the event an action is brought to enforce the terms and conditions of this Agreement, the prevailing party shall be entitled to reasonable attorneys' fees, both at trial and on appeal. - END -

1 Quick Reference This guide is provided to help get your installation up-and-run- ning quickly and efficiently. For more details, including program- ming information, reference the Product Reference Guide (PRG), which is available for viewing and download from the Datalogic website listed on the back cover of this manual. Installation Route the interface cable from the terminal or host. Plug the AC adapter (if one is used) into a wall outlet and the interface (I/F) cable, then route and attach the I/F cable to the scanner. Verify operation by presenting known-good barcodes to the scanner. The unit should beep1 and/or flash its good read LED and send the barcode data to the host or terminal. If not, refer to the Trou- bleshooting section of this guide. Scanner installation is complete. 1. Beeper and LED behavior is selectable and may have been disabled by a pre- vious user. I/F Cable Connect Here A/C Adapter (if needed) For 220-230 VAC adapters, the cord must be facing down as shown in the illustration. If installed upwards, it will pose an undue strain on the socket outlet. To Host/Terminal

manently attached to a wall or countertop. After locating the stand in an optimal position, the scanner (along with the stand) can be detached for portable use by lifting the entire unit as shown below. Power Supply Models require1 either a Listed class II or class III with a Limited Power Source (LPS). For the safety certification to be valid, class III input power sources must be IEC/EN60950-1 (EN 60335- series, EN 60065 or relevant) approved. How to Scan barcodes can be presented to the scanner while it is resting on the counter or in the optional stand, or the scanner/mount can be lifted and held as shown. 1. Power Off the Terminal (POT) units do not require a power supply. Input: 100 - 240 VAC Output: 5 VDC Max. Current: 2.5 A Max. Power: 12.5 W System Input Voltage Input: 4.5 - 14.0 VDC Max. Power: 2.5 W *Optional Stand Optional Scan Button Shown

3 Targeted Scanning Mode In order to read a barcode (button option only)... • press and hold the scan button. An aiming pattern will appear. • with the aiming pattern fairly centered over the barcode to be read, release the button to read the label. Troubleshooting If the scanner is not operating properly, the following checks should be performed: 1. If the scanner uses an external power supply and the external power supply has failed, the scanner will not operate. Exchange the power supply with a known good power sup- ply and retest operation. 2. Verify the interface cable is securely attached to the host. Consult your technical support personnel or refer to your host system manual to verify the proper connection for the scanner. NOTE The scanner will not read barcodes while the button is pressed. Targeted Scanning Mode will read barcodes in any orientation. The scanner will return to full pattern Omni Mode after a configurable time has elapsed. 1 2 4 Product Reference Guide 5 3

ner. 4. Check that the barcodes are of sufficient quality to be recog- nized by the scanner. Wrinkled, smudged, or torn labels can cause the scanner to not read at all. Scan known-good labels of an active symbology1 to check the scanner's read opera- tion. 5. Ensure that the scanner's interface type is compatible with the host terminal by consulting your POS system manual and/or the Product Reference Guide. If the scanner still does not function properly, contact your local supplier or Datalogic Customer Support Services. Compliance Statement This Class B digital apparatus complies with Canadian ICES -003. Cet appareil numérique de la classe B est confrome à la norme NMB-003 du Canada. LED Class CLASS 1 LED PRODUCT APPARECCHIO LED CLASSE 1 LED KLASSE 1 APPAREIL A LED DE CLASSE 1 EN60825-1 and IEC 26471 1. Reading of the various barcode symbologies can be independently enabled or disabled in the scanner.

efficace. Per ulteriori dettagli, inclusi i dettagli relativi alla pro- grammazione, consultare la Guida di Riferimento del Prodotto, che può essere consultata online e scaricata dal sito di Datalogic indicato sul retro del presente manuale. Installazione Svolgere il cavo d'interfaccia dal terminale o host. Inserire l'even- tuale adattatore CA nella presa a parete e nel cavo d'interfaccia (I/ F), quindi collegare il cavo I/F allo scanner. Verificare il funziona- mento facendo leggere allo scanner dei codici a barre dei quali si conosce il contenuto e in buono stato. L'unità emettera un suono1 e/o farà lampeggiare il LED che segnala la corretta lettura del codice e invierà i dati del codice all'host o al terminale. In caso contrario, consultare la sezione "Risoluzione dei problemi" della presente guida. L'installazione dello scanner è completa. 1. È possibile selezionare suono oppure LED. Tenere conto della configurazione impostata dall'utente che ha utilizzato lo scanner in precedenza. Cavo d'interfaccia Collegare qui Adattatore C (se necessario) All'host/terminale Il cavo degli adattatori 220-230 VCA deve essere posizionato verso il basso come indicato nell'illustrazione. In caso contrario l'uscita della presa di corrente sarà sotto sforzo.

manentemente alla parete o sul bancone. Dopo aver posizionato il supporto in posizione ottimale, lo scanner e il supporto potranno essere staccati per l'utilizzo mobile sollevando l'intera unità come illustrato in basso. Alimentazione Questi modelli1 devono essere alimentati con alimentatori omologati di classe II o classe III LPS (Limited Power Source, sor- gente di corrente limitata). Affinché il certificato di sicurezza sia valido, le sorgenti di alimentazione di classe III devono essere conformi a IEC/EN60950-1 (serie EN 60335, EN60065 o rela- tivi). Come utilizzare lo Scanner È possibile presentare i codici al lettore, mentre è posizionato sul bancone oppure inserito nel supporto opzionale, oppure lo scan- ner può essere sollevato come da illustrazione. 1. Le unità alimentate dal terminale (POT - Power Off the Terminal) non richie- dono alimentazione di rete. Tensione ingresso: 100 - 240 VAC Tensione uscita: 5 VDC Consumo massimo: 2.5 A Potenza massima: 12.5 W Sistema di tensione in ingresso Tensione ingresso: 4.5 - 14.0 VDC Potenza massima: 2.5 W *Supporto opzionale Pulsante opzione

Per utilizzare lo scanner con il pulsante opzione: • tenere premuto il pulsante. Apparirà un mirino lumi- noso. • Posizionare il mirino luminoso al centro del codice a barre da leggere e rilasciare il pulsante opzione per eseguire la lettura. Risoluzione dei Problemi Nel caso lo scanner non funzionasse correttamente, eseguire i seg- uenti controlli: 1. Se lo scanner utilizza un'alimentazione esterna e quest'ultima non fosse operativa, lo scanner non funzionerà. Utilizzare una sorgente di alimentazione affidabile e riprovare. 2. Verificare che il cavo d'interfaccia sia saldamente collegato all'host. Consultare il proprio personale tecnico oppure il manuale del sistema host per controllare il corretto collega- mento dello scanner. NOTE Lo scanner non legge i codici, se il pulsante è premuto. La modalità di scansione bersaglio consente di leggere codici orientati in qualunque verso. Lo scanner ritornerà in modalità Omni dopo un periodo di tempo impostabile. 1 2 4 Product Reference Guide 5 3

allo scanner. 4. Controllare che i codici a barre siano di qualità sufficiente- mente leggibile per lo scanner. Etichette piegate, strappate o sbavate potrebbero non essere leggibili. Utilizzare etichette sicuramente leggibili che appartenengono ad un sistema di simbologia1 utilizzato per controllare il funziomento dello scanner in lettura. 5. Assicurarsi che il tipo di interfaccia dello scanner sia compat- ibile con il teminale/host consultando il manuale del POS e/ o la Guida di riferimento del prodotto. Se lo scanner non funziona correttamente, contattare il rivendi- tore locale oppure il Servizio Assistenza Clienti di Datalogic. Dichiarazione di Conformità Il presente apparto digtale di Classe B è conforme alla normativa canadese ICES-003. Classe LED CLASS 1 LED PRODUCT APPARECCHIO LED CLASSE 1 LED KLASSE 1 APPAREIL A LED DE CLASSE 1 PRODOTTO LED CLASSE 1 EN60825-1 e IEC 26471 1. La lettura delle varie simbologie dei codici a barre può essere indipendente- mente abilitata o disabilitata nello scanner.

9 Guía de Referencia Rápida La finalidad de esta guía es ayudarle a instalar el equipo de forma rápida y eficiente. Para obtener más datos, incluida información de programación, consulte la Guía de referencia del producto (PRG) que podrá ver y descargar de la página Web de Datalogic, cuya dirección aparece en la contracubierta de este manual. Instalación Encamine el cable de interfaz desde el terminal o el equipo cen- tral. Conecte el adaptador de CA (si se utiliza uno) a una toma de corriente de pared y al cable de interfaz (I/F). A continuación encamine y conecte el cable I/F al escáner. Para comprobar el fun- cionamiento, coloque un código de barras en buen estado ante el escáner. La unidad emitirá un pitido1 y/o parpadeará el LED de lectura correcta y enviará los datos del código de barras al equipo central o al terminal. Si no es así, consulte la sección Solución de averías de esta guía. La instalación del escáner ha finalizado. 1. El funcionamiento del indicador acústico y el LED es seleccionable y es posi- ble que un usuario anterior lo haya desactivado. Cable de interfaz Conectar aquí Adaptador de CA (si es necesario) Al equipo central/terminal Si se utilizan adaptadores de 220-230 V CA, el cable debe orientarse hacia abajo, como muestra la imagen. Si se instala hacia arriba, ejercerá una tensión indebida sobre la toma de corriente.

forma permanente a una pared o a un mostrador. Después de colocar el soporte en la posición óptima, se podrá desmontar el escáner (junto con el soporte) si desea trasladarlo de lugar. Para ello, solo tiene que elevar la unidad completa, tal y como muestra la imagen. Suministro Eléctrico Se require fuente limitada1 de alimentación (LPS) alistada en la clase II o la clase III para estos modelos. La certificación de seguri- dad solamente es válida si las enchufadas para fuente de aliment- ación clase III están aprobadas por IEC-EN60950-1 (serie EN 60335, EN 60065 o comparable). Instrucciones Para Escanear Los códigos de barras pueden colocarse delante del escáner mien- tras éste permanece apoyado sobre el mostrador o el soporte opcional. También es posible elevar y sostener el escáner/unidad como muestra la imagen. 1. Las unidades de desconexión del terminal (POT) no precisan una fuente de alimentación. Enchufada: 100 - 240 VAC Despacho: 5 VDC Corriente máximo: 2.5 A Poder máximo: 12.5 W Sistema de tensión de entrada Enchufada: 4.5 - 14.0 VDC Poder máximo: 2.5 W *Soporte opcional Opción de interruptor mostrada

11 Modo de Exploración de Objetivo Para leer un código de barras (solo opción de interruptor)... • Mantenga pulsado el interruptor. Aparecerá un haz para apuntar. • Centre el haz para apuntar lo más posible sobre el códi- go de barras que vaya a leer y suelte el interruptor para leer la etiqueta. Solución de Problemas Si el escáner no funciona correctamente, deberán realizarse las siguientes comprobaciones: 1. Si el escáner utiliza una fuente de alimentación externa y dicha fuente se ha averiado, el escáner no funcionará. Cam- bie la fuente de alimentación por otra en buen estado y restablezca el funcionamiento. 2. Compruebe que el cable de interfaz está perfectamente acop- lado al equipo central. Pida ayuda al personal de asistencia técnica o consulte el manual del sistema central para com- probar que el escáner esta correctamente conectado. NOTA El escáner no leerá códigos de barras mientras el interruptor permanezca pulsado. El modo de exploración de objetivo leerá los códigos de barras en cualquier dirección. El escáner volverá al modo de haz completo una vez que haya transcurrido un tiempo configurable. 1 2 4 Product Reference Guide 5 3

acoplado al escáner. 4. Compruebe que los códigos de barras tienen la calidad sufi- ciente para ser reconocidos por el escáner. El escáner no leerá etiquetas arrugadas, emborronadas o rasgadas. Para compro- bar el funcionamiento de la función de lectura del escáner, explore etiquetas que contengan una simbología activa en buen estado1. 5. Asegúrese de que el tipo de interfaz del escáner es compatible con el terminal central. Para ello, consulte el manual del sistema POS y/o la Guía de referencia del producto. Si el escáner sigue sin funcionar correctamente, póngase en con- tacto con su proveedor local o con el Departamento de Atención al Cliente de Datalogic. Nota de Conformidad Este aparato digital de Clase B cumple la normativa canadiense ICES -003. Clase de LED CLASS 1 LED PRODUCT APPARECCHIO LED CLASSE 1 LED KLASSE 1 APPAREIL A LED DE CLASSE 1 PRODUCTO LED de CLASE 1 EN60825-1 y IEC 26471 1. La lectura de distintas simbologías de códigos de barras puede activarse o desactivarse de forma independiente en el escáner.

rápida e eficientemente. Para obter maiores detalhes, incluindo informações de programação, consultar o Guia de Referência do Produto (PRG), que está disponível para visualização e download a partir do web-site Datalogic listado na contracapa deste manual. Instalação Rotear o cabo de interface a partir do terminal ou do host. Ligar o adaptador C.A. (se for usado um) em uma tomada na parede e o cabo de interface (I/F), então rotear e conectar o cabo I/F ao leitor. Verificar a operação apresentando códigos de barra em bom estado e reconhecidos pelo leitor. A unidade deve emitir um bip1 e/ou lampejar sua boa leitura, enviando os dados de código de barras para o host ou terminal. Caso contrário, consultar a seção Diagnóstico deste guia. A instalação do leitor está completa. 1. O comportamento do bip e do LED pode ser selecionado e pode estar des- abilitado por um usuário anterior. Cabo de interface Conectar aqui Adaptador C.A. (se necessário) Para Host/Terminal Para adaptadores 220-230 VAC, o fio deve estar voltado para baixo, como mostrado na ilustração. Se for instalado para cima, irá causar peso indevido na saída do soquete.

conectado permanentemente a uma parede ou um balcão. Após localizar o balcão em uma boa posição , o leitor (paralelo ao bal- cão) pode ser destacado para uso portátil, levantando a unidade como mostrado abaixo. Adaptador C.A / C.C. Modelos podem ser classificados1 como Classe II ou Classe III, com Fonte de Energia Limitada (LPS). Para o certificado de segu- rança eletrica ser válido, uma fonte de entrada de energia Classe III precisa ser approvada como IEC/EN60950-1 (EN 60335- serie, EN 60065 ou relevante). Como Fazer Leitura Os códigos de barra podem ser apresentados ao leitor enquanto este está no balcão ou na suporte opcional, ou o leitor/montagem pode ser levantado e segurado como mostrado abaixo. 1. Fornecimento de energia das unidades do tipo POT não exigem uma fonte de energia externa. Entrada: 100 - 240 V c.a. Saída: 5 VDC Corrente Max.: 2.5 A Potencia Max.: 12.5 W Sistema de tensão de entrada Entrada: 4.5 - 14.0 VDC Potencia Max.: 2.5 W *Suporte opcional Opção com Botão

Para ler um código de barra (somente opção de butão)... • Pressionar e segurar o butão. Um padrão almejado irá aparecer. • Com o padrão almejado centrado no código de barra para ser lido, soltar o butão para ler a etiqueta. Diagnóstico Se o leitor não estiver operando de forma apropriada, as seguintes to verificações devem ser realizadas: 1. Se o leitor usar um fornecimento de energia externo e este estiver falhando, o leitor não irá operar. Trocar o fornecedor de energia com um reconhecidamente bom e testar nova- mente a operação. 2. Verificar se o cabo de interface está conectado com segurança ao host. Consultar seu suporte técnico ou o manual do sistema host para verificar a conexão apropriada para o leitor. NOTA O leitor não irá ler códigos de barra enquanto o butão estiver pressionado. Modo de Leitura Etiquetado irá ler códigos de barra em qualquer orientação. O leitor irá retornar para o padrão total Omni Mode depois que um tempo configurável tiver passado. 1 2 4 Product Reference Guide 5 3

segura ao leitor. 4. Verificar se os códigos de barra são de qualidade suficiente para serem reconhecidos pelo leitor. Etiquetas dobradas, manchadas ou molhadas podem fazer com que o leitor não as leia. Fazer o scan de etiquetas boas de uma simbologia1 para verificar a operação de leitura do leitor. 5. Garantir que o tipo de interface do leitor é compatível com o terminal host, consultando seu manual do sistema PDV e/ou o Guia de Referência do Produto. Se o leitor não funcionar ainda adequadamente, contactar seu for- necedor local ou os Serviços de Suporte ao Cliente. Declaração de Conformidade Este equipamento digital Classe B atende à norma Canadense ICES -003. Classe LED CLASS 1 LED PRODUCT APPARECCHIO LED CLASSE 1 LED KLASSE 1 APPAREIL A LED DE CLASSE 1 PRODUTO LED CLASSE 1 EN60825-1 e IEC 26471 1. A leitura de várias simbologias de código de barra pode ser independente- mente habilitada ou desabilitada no leitor.

17 Guide de Référence Rapide Ce guide est fourni afin de vous aider à installer rapidement et efficacement votre lecteur de codes à barres. Pour plus de détails concernant les informations sur la programmation, consultez le Guide de Référence du Produit qui est disponible soit pour lec- ture soit pour téléchargement à partir du site Internet Datalogic indiqué au dos de ce manuel. Installation Acheminez le câble d'interface à partir du terminal ou de l'ordi- nateur hôte. Branchez l'adaptateur CA (courant alternatif) (s'il est nécessaire d'en utiliser un) à une prise du mur et le câble d'interface (I/F), ensuite acheminez et connectez le câble I/F au scanner. Vérifiez l'opération en présentant au scanner des codes à barres corrects. l'unité devrait émettre un bip1 sonore et/ou faire clignoter la diode pour confirmer que la saisie est correcte et envoyez les données du codes à barres à un ordinateur hôte ou au terminal. Si ce n'est pas le cas, consultez la section Diagnostic de Pannes de ce guide. L'installation du scanner est terminée. 1. Le bip sonore et le clignotement de la diode LED peuvent être sélectionnés et peuvent avoir été désactivés par un utilisateur précédent. Câble d'Interface Connectez ici Adaptateur CA (si nécessaire) A l'ordinateur hôte/Terminal Pour les adaptateurs 220- 230 VCA, le cordon doit être face vers le bas comme montré sur l'illustration. S'il est installé vers la haut, ceci provoque une tension excessive au niveau de la prise.

fixé en permanence à un mur ou à un comptoir. Après avoir placé le support dans une position optimale, le scanner (ainsi que le support) peuvent être détachés pour un usage portatif en levant l'unité complète comme illustré ci-dessous. Alimentation Électrique Modèles1 référencés Classe II et Classe III nécessitant une ali- mentation externe (Limited Power Source). Afin de valider le cer- tificat de sécurité, l’alimentation classe III doit être certifiée IEC/ EN60950-1 (Séries EN 60335, EN 60065 ou équivalent). Comment Scanner La lecture peut être en mode mains libres pour les pièces faciles à manipuler ou à la main pour les pièces plus encombrantes. 1. Les unités de mise hors tension du terminal n'exigent aucune alimentation électrique. Tension d'entrée: 100 - 240 VAC Tension de sortie: 5 VDC Max. de courant: 2.5 A La puissance max.: 12.5 W Système de tension d'entrée Tension d'entrée: 4.5 - 14.0 VDC La puissance max.: 2.5 W *Support Facultatif Bouton pour mode ciblée

19 Mode Saisie Ciblée Afin de saisir un code-barre (option commutation uniquement)... • appuyez et maintenez la pression sur le bouton de com- mutation. Un rayon de visée apparaîtra. • centrez bien le rayon de visée au-dessus du codes à barres qui doit être saisi, puis relâchez le bouton pour lire l'étiquette. Diagnostic de Pannes Si le lecteur ne fonctionne pas correctement, effectuez les vérifica- tions suivantes : 1. Si le lecteur utilise une alimentation électrique extérieure et que l'alimentation extérieure ne fonctionne pas, le lecteur ne fonctionnera pas. Echangez la source d'alimentation avec une autre alimentation électrique correcte et effectuez de nouveau l'opération pour vérification. 2. Vérifiez que le câble d'interface est correctement connecté à l'ordinateur hôte/terminal. Consultez votre service tech- nique ou référez-vous au manuel de votre ordinateur hôte afin de vérifier si la connexion au lecteur est correcte. NOTE Le scanner ne lira pas les codes à barres tant que le bouton sera enfoncé. Le Mode de Saisie Ciblée lira les codes à barres dans n'importe quel sens. Le scan- ner retournera complètement en mode Omni après qu'un certain temps configurable se sera écoulé. 1 2 4 Product Reference Guide 5 3

4. Contrôlez que la qualité des codes à barres est suffisante pour que ceux-ci soient reconnus par le scanner. Les étiquettes pliées, sales ou déchirées peuvent empêcher le scanner de lire les codes. Saisissez des étiquettes correctes avec une symbologie1 active afin de vérifier que le scanner effectue l'opération de saisie correctement. 5. Assurez-vous que le type d'interface du scanner est compati- ble avec le terminal hôte en consultant la manuel de votre système POS et/ou le Guide de Référence du Produit. Si le lecteur ne fonctionne toujours pas correctement, contactez votre fournisseur local ou le Service d'Assistance Clientèle de Datalogic. Déclaration de Conformité This Class B digital apparatus complies with Canadian ICES -003. Cet appareil numérique de la classe B est confrome à la norme NMB-003 du Canada. LED Class CLASS 1 LED PRODUCT APPARECCHIO LED CLASSE 1 LED KLASSE 1 APPAREIL A LED DE CLASSE 1 PRODUIT LED CLASSE 1 EN60825-1 et IEC 26471 1. La lecture des différentes symbologies et de codes à barres peuvent être activées ou désactivées de façon indépendante.

Inbetriebnahme ermöglichen. Weitere Einzelheiten, u.a. zur Pro- grammierung, entnehmen Sie dem Produktleitfaden (Product Reference Guide, PRG), der zum Anzeigen und Herunterladen auf der Datalogic-Webseite verfügbar ist (siehe Rückseite dieses Leitfadens). Installation Verlegen Sie das Interfacekabel vom Haupt- oder Endgerät. Schließen Sie den Netzadapter (sofern verwendet) an einer Netz- steckdose und am Interfacekabel (IF-Kabel) an, und verlegen Sie das IF-Kabel zum Scanner und schließen es daran an. Führen Sie einen Funktionstest aus, indem Sie mit dem Scanner garantiert funktionsfähige Barcodes einlesen. Das Gerät muss einen Piep- ton1 aussenden und/oder mit der gut sichtbaren LED blinken und die Barcodedaten an das End- oder Hauptgerät senden. Andernfalls ziehen Sie den Abschnitt zu Fehlerbehebung in diesem Leitfaden zurate. Die Scannerinstallation ist abgeschlossen. 1. Piepton- und LED-Verhalten können eingestellt werden und sind durch Vor- nutzer ggf. deaktiviert. Interfacekabel Hier anschließen Netzadapter (falls erforderlich) Zum End-/Hauptgerät Bei 220-230 V- Adaptern, muss das Kabel wie in der Abbildung nach unten zeigen. Wenn es nach oben zeigt, wird die Steckdose unnötig belastet.

Befestigung an einer Wand oder Ladentheke. Nachdem Sie den Sockel optimal positioniert haben, können Sie den Scanner (mit Sockel) für freihändigen Einsatz abnehmen, indem Sie das gesa- mte Gerät wie unten dargestellt anheben. Stromversorgung Die Modelle1 erfordern eine Stromquelle der Klasse II oder III mit einer Leistungsbegrenzung (LPS). Für eine gültige Sicher- heitszertifizierung müssen Klasse III Stromquellen am Eingang nach den Bestimmungen IEC/EN60950-1 (EN 60335-Serien, EN 60065 oder entsprechenden) zugelassen sein. Scanverfahren Barcodes werden mit dem Scanner eingescannt, während dieser auf der Ladentheke steht oder am optionalen Sockel befestigt ist, oder indem der Scanner/die Halterung hochgehoben und wie folgt gehalten wird. 1. Für Geräte mit POT-Option (Power Off the Terminal) ist keine Stromver- sorgung erforderlich. Eingang: 100 - 240 VAC Ausgang: 5 VDC Max. Strom: 2.5 A Max. Leistung: 12.5 W System Eingangsspannung Eingang: 4.5 - 14.0 VDC Max. Leistung: 2.5 W *Optionaler Sockel Optionaler Schalter

• Schalter gedrückt halten Ein Zielmuster wird angezeigt. • Zielmuster entsprechend über dem einzulesenden Bar- code ausrichten und Schalter zum Scannen des Etiketts loslassen. Fehlerbehebung Bei fehlerhaftem Scannerbetrieb prüfen Sie Folgendes: 1. Wenn der Scanner mit einer externen Stromversorgung betrieben wird, funktioniert er nicht, wenn diese ausfällt. Stromversorgung durch ein garantiert funktionsfähiges Gerät ersetzen und Betrieb testen. 2. Sicherstellen, dass das Interfacekabel am Endgerät richtig angeschlossen ist. Wenden Sie sich an Ihr zuständiges Tech- nikpersonal oder ziehen Sie das Endgeräthandbuch zurate, um einen ordnungsgemäßen Anschluss des Scanners sicher- zustellen. HINWEIS Bei gedrücktem Schalter werden die Barcodes vom Scanner nicht eingelesen. Mit dem Zielscanmodus werden Barcodes in jeder Ausrich- tung eingelesen. Der Scanner wechselt nach Ablauf einer konfigurierbaren Zeit wieder in den omnidirektionalen Vollmustermodus. 1 2 4 Product Reference Guide 5 3

angeschlossen ist. 4. Sicherstellen, dass die Barcodes ausreichende Qualität aufweisen, um vom Scanner erkannt zu werden. Zerknitterte, beschmierte, oder angerissene Etiketten machen ein Einlesen unmöglich. Scan- nen Sie garantiert gute Etiketten mit aktiver Symbologie1, um die Einlesefunktion des Scanners zu überprüfen. 5. Vergewissern Sie sich, dass der Schnittstellentyp des Scanners mit dem Endgerät kompatibel ist, indem Sie das Handbuch des POS-Systems und/oder den Produktleitfaden (Product Reference Guide) zurate ziehen. Wenn der Scanner weiterhin nicht ordnungsgemäß funktioniert, wenden Sie sich an Ihren örtlichen Händler oder an den Data- logic-Kundensupport. Erfüllung von Vorschriften Dieses Digitalgerät der Klasse B entspricht dem kanadischen Standard ICES -003. LED-Klasse CLASS 1 LED PRODUCT APPARECCHIO LED CLASSE 1 LED KLASSE 1 APPAREIL A LED DE CLASSE 1 KLASSE 1 LED-PRODUKT EN60825-1 und IEC 26471 1. Das Einlesen der verschiedenen Barcodesymbologien kann im Scanner unabhängig aktiviert bzw. deaktiviert werden.

㓚᥹ষˈ✊ৢᏗ㒓ᑊᇚ,) ⬉㓚䖲᥹ࠄᠿᦣ఼DŽ⫼Ꮖⶹⱘ དᴵᔶⷕ䖯㸠ẔᶹDŽᠿᦣ఼ⱘ୛ু  ᑨ䆹号ડᑊϨ  ៪㗙ᅗⱘ/(' ᑨ䆹䮾⚕ҹ㸼⼎䇏᭄ℷ ⹂ˈৠᯊᇚᴵⷕ᭄᥂থ䗕ࠄЏᴎ៪㗙㒜ッDŽབᵰ᮴号ડ៪ 㗙ϡ䮾⚕ˈখ䯙ᴀᣛफⱘᬙ䱰Ẕׂ䚼ߚDŽ 㟇ℸ ᠿᦣ఼ᅝ㺙ᅠ↩DŽ  㳖号఼੠/(' ⱘ⢊ᗕৃ䗝ˈᑊৃ⬅ܜࠡ⫼᠋⽕ℶDŽ

⬉⑤ ᳝ѯൟো㽕∖Փ⫼᠔߫ߎⱘ㄀ ㉏៪㗙/36 ⬉⑤ ᇍ ᠿᦣ఼䖯㸠Ⳉ᥹կ⬉DŽ⬉⑤ഫ㽕∖FODVV,, ៪FODVV,,, ᳝䰤⬉⑤DŽ Ўֱ䆕ᅝܼ䆕к᳝ᬜˈFODVV,,, 䕧ܹ⑤ᖙ乏⒵䎇 ,(&(1(1VHULHV(1RU UHOHYDQW ᷛޚDŽ ᗢḋ䖯㸠ᠿᦣ ᇚᴵⷕ䴭ℶ೼ᶰৄϞ៪㗙ৃ䗝ᴎᑻϞᇍⴔᠿᦣ఼ˈ៪ 㗙ᇚᠿᦣ఼ ᴎᑻབ೒᠔⼎䙷ḋВ䍋ৢ䖯㸠ᠿᦣDŽ  327 ൟϡ䳔㽕⬉⑤DŽ 䕧ܹ 9$& 䕧ߎ9'& ᳔໻⬉⌕$ ᳔໻ࡳ⥛: ㋏㒳䕧ܹ⬉य़ 䕧ܹ9'& ᳔໻ࡳ⥛:

ᖿ䗳খ㗗 27 ⵘޚᠿᦣ῵ᓣ Ўњ䇏ᴵⷕ ҙ䗖⫼Ѣᓔ݇ൟˈᑨ䆹˖ 噝 य़ϟᓔ݇ᑊֱᣕˈ䖯ܹⵘޚ῵ᓣDŽ 噝 ೼ⵘޚ῵ᓣϟᇍޚ㽕䇏পⱘᴵⷕˈᵒᓔᓔ݇䇏ᷛ ㅒDŽ ᬙ䱰໘⧚ བᵰᠿᦣ఼ϡ㛑ℷᐌᎹ԰ˈᑨᔧ䖯㸠ҹϟẔᶹ˖ བᵰᠿᦣ఼Փ⫼໪䚼⬉⑤կ⬉㗠໪䚼⬉⑤থ⫳ᬙ䱰ˈ ߭ᠿᦣ఼ϡӮᎹ԰DŽ⫼Ꮖⶹⱘ㛑ℷᐌᎹ԰ⱘ⬉⑤䖯㸠 ᳓ᤶᑊ䞡ᮄ䖯㸠䆩偠DŽ Ẕ偠᥹ষ⬉㓚ϢЏᴎᰃ৺⠶೎ഄ䖲᥹DŽ੼䆶ᡔᴃᬃᣕ Ҏਬ៪খ䯙Џᴎ㋏㒳ᣛफҹḌᅲᠿᦣ఼ᰃ৺Ꮖ㒣䗖ᔧ ⱘ䖲᥹DŽ ⊼ᛣ ೼ᓔ݇㹿ᣝⴔᯊᠿᦣ఼ϡӮ䇏ᴵⷕDŽ ⵘޚᠿᦣ῵ᓣ㛑೼ӏᛣᮍ৥Ϟ䇏ᴵⷕDŽ ೼ϔᅮᯊ䯈Пৢᠿᦣ఼ᇚ䖨ಲࠄܼ৥῵ᓣDŽ 1 2 4 Product Reference Guide 5 3

ⱘ᥹ষ㉏ൟϢЏᴎ㒜ッݐᆍDŽ བᵰᠿᦣ఼ҡ✊ϡ㛑ℷᐌᎹ԰ˈৃϢᴀഄկᑨଚ៪㗙'DW- DORJLF ⫼᠋ᬃᣕ᳡ࡵЁᖗ㘨㋏DŽ ヺড়⊩㾘ໄᯢ % ㉏᭄ᄫᓣ䆒໛ヺড়ࡴᣓ໻,&(6DŽ /(' ㉏ ㄀ ㉏/(' ѻક (1 ,(&

さい。PRG は、このマニュアルの背表紙に記載されている Datalogic Web サイトからダウンロードすることができます。 インストール インターフェース·ケーブルをターミナルまたはホストに接続 します。必要に応じて AC アダプタを壁コンセントおよびイン ターフェース (I/F) ケーブルに接続し、I/F ケーブルをスキャ ナに接続します。状態のよいバーコードをスキャンし、正しく 作動するか確認してください。ユニットはビープ音1 を発する か、読み取り正常 LED を点滅させ、ホストまたはターミナル にバーコード·データを送信します。正しく作動しない場合 は、このガイドのトラブルシューティング·セクションを参照 してください。 これで、スキャナのインストールが完了しました。 1. ビーパーおよび LED の動作は選択可能です。また、以前のユーザーに より無効にされている場合があります。 Ȁ

られた電源(LPS) を必要とします。安全証明が有効であるため には、クラスIII の入力電源がIEC/EN60950-1(EN 60335 シ リーズ、EN60065、もしくは同等) に承認されなければなら なりません。 スキャンの仕方 スキャナを卓上またはオプションのスタンドに置いた状態、ま たはスタンドを取り付けたスキャナを図のように持ち上げた状 態で、バーコードをスキャンすることができます。 1. POT (Power Off the Terminal) ユニットには電源は不要です。 入力: 100 - 240 VAC 出力: 5 VDC 最大. 電流: 2.5 A 最大. 電力: 12.5 W システム入力電圧 入力: 4.5 - 14.0 VDC 最大. 電力: 2.5 W

のみ) ⋯ 噝 ɁȬɋɉȧᢐǬǴȓȓȀǬȓǮDŽ✻⑪əɇόɻ ǡ㸼⼎ǪȡȓǮDŽ 噝 ✻⑪əɇόɻȧ䂁ȔপȠɘόȻόɑȃЁ༂Ȁᔧ ǻǃɁȬɋɉȧᬒǬǻɱɡɳȧ䂁ȔপȟȓǮDŽ トラブルシューティング スキャナが正しく作動しない場合は、以下の確認作業を行って ください。 1. 外部電源をお使いの場合は、外部電源が故障すると スキャナも作動しません。信頼できる電源装置と交 換し、スキャナが作動するか再テストしてくださ い。 2. インターフェース·ケーブルがホストにしっかりと接続さ れていることを確認してください。スキャナの正しい接続 方法については、テクニカルサポートの担当者にお問い合 注記 スイッチを押したままの状態では、スキャナ はバーコードを読み取りません。 目標スキャニング·モードでは、任意の向き のバーコードを読み取ることができます。 設定時間を過ぎると、スキャナはフル·パタ ーン·オムニ·モードに戻ります。 1 2 4 Product Reference Guide 5 3

ービスまでご連絡ください。 適合性について 本製品は、VCCI に適合したクラスB デジタル装置です。 LED クラス クラス 1 LED 製品 EN60825-1 IEC 26471 1. さまざまなバーコード体系ごとに、スキャナでの読み取りを有効または 無効にすることができます。

digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installa- tion. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with these instructions, may cause harmful interference to radio communications. However, there is no guarantee that inter- ference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: • Reorient or relocate the receiving antenna • Increase the separation between the equipment and receiver • Connect the equipment into an outlet on a circuit different from that to which receiver is connected • Consult the dealer or an experienced radio / TV technician for help. CAUTION The User is cautioned that changes or modifi- cations not expressly approved by the part responsible for compliance could void the user’s authority to operate the equipment.

and found compliant to the following directives and standards. Apparatus: Magellan® 1100i Omni-directional Imaging Scanner EU Directives: EMC 2004/108/EC Low Voltage 2006/95/EC RoHS 2002/95/EC WEEE 2002/96/EC Standards: EN 55022: 2007 EMC EN 55024: 2003 Immunity EN 60950-1:2004 ITE Safety EN 60825-1: 2007 Laser Safety EN 61000-3-2:2006 Harmonic Current EN 61000-3-3:2005 Voltage Fluctuation/Flicker IEC 26471:2006 Photobiological Safety of Lamps Equipment Type: Barcode Scanning Equipment Product Model Name: Magellan® 1100i Date Placed into EU Service: May 2009 under the Datalogic trademark. Responsible Manufacturer: Datalogic Scanning, Inc. 959 Terry St. Eugene, OR 97402 USA EUROPEAN DECLARATION OF CONFORMITY Vice President Supply Chain Operations Datalogic Scanning, Inc.

R44-3015 (Rev. X1) 5/09 Datalogic Scanning, Inc. 959 Terry Street Eugene, OR 97402 USA Telephone: (541) 683-5700 Fax: (541) 345-7140 Australia Datalogic Scanning Pty Ltd Telephone: [61] (2) 9870 3200 [email protected] France and Benelux Datalogic Scanning Sarl Telephone: [33].01.64.86.71.00 [email protected] Germany Datalogic Scanning GmbH Telephone: 49 (0) 61 51/93 58-0 [email protected] India Datalogic Scanning India Telephone: 91- 22 - 64504739 [email protected] Italy Datalogic Scanning SpA Telephone: [39] (0) 39/62903.1 [email protected] Japan Datalogic Scanning KK Telephone: 81 (0)3 3491 6761 [email protected] Latin America Datalogic Scanning, Inc Telephone: (305) 591-3222 [email protected] Singapore Datalogic Scanning Singapore PTE LTD Telephone: (65) 6435-1311 [email protected] Spain and Portugal Datalogic Scanning Sarl Sucursal en España Telephone: 34 91 746 28 60 [email protected] United Kingdom Datalogic Scanning LTD Telephone: 44 (0) 1923 809500 [email protected] www.scanning.datalogic.com