Alesis RA100 Reference Manual

Text of Alesis RA100 Reference Manual

CHAPTER 1 – GETTING TO KNOW THE RA-100

1.1 INTRODUCTION.....................................................................................1 Principal Features................................................................................1 Unpacking and Inspection.................................................................3 About This Manual.............................................................................4 CHAPTER 2 – INSTALLATION 2

4.3 KEYBOARD AMPLIFICATION SYSTEM............................................19

4.4 GUITAR AMPLIFICATION SYSTEM..................................................20 4.5 BIAMP SOUND REINFORCEMENT...................................................21 CHAPTER 5 – MAINTAINANCE/SERVICE 5.1 GENERAL INFORMATION..................................................................22 Cleaning..........................................................................

Alesis RA100 MEET THE RA-100

1.1 INTRODUCTION Principal Features Congratulations on your purchase of the Alesis RA-100 Reference Amplifier. With all the wondrous advances in both analog and digital electronics in the past few years, it’s easy to forget that an audio chain is only as good as its weakest link. With low-cost digital devices now offering sound quality unheard of only a few years ago, Alesis has applied its expertise toward creating a sonicall

power-down. Nonetheless, there’s a 2-second mute on power-up to

compensate for any pieces of equipment plugged into the RA-100 that produce transients upon power-up, and receive power at the same time as the RA-100. Also, because the amp doesn’t produce power on/off thumps itself, the mute circuit can be pre-power amp. This allows simpler circuitry than what would be required for shutting down the power amp stages. • The RA-100’s power supply has

Alesis RA100 • No “speaker stress” during shutdown. With traditional protection circuitry,

the act of clamping the output devices to a safe value can make the amp unstable with particular notes that interact with the speaker resonance, thus producing oscillation or “motorboating.” This could damage your speakers. The RA-100 uses an elegant clamping design that observes the load at all times but also integrates the signal characteristics into the clamping acti

• Alesis RA-100 power amp with the same serial number as shown on the

shipping carton • Power cord. • Four stick-on rubber feet (for shelf mounting, to prevent the RA-100’s bottom surface from scratching the shelf) • Alesis warranty card. It is important to register your purchase; if you have not already filled out your warranty card, please do so now. About This Manual The manual presents information in a logical order. Chapter 2 covers installa

2.1 REAR PANEL CONNECTIONS

The following diagram shows the various rear-panel components. Please refer to this diagram during the procedures described in this chapter. Fuse: 5 Amps (A spare fuse in included in the fuse holder) Right Input Left Input Right Phone Plug Output Left Phone Plug Output Left Push Clip Outputs Right Push Clip Outputs AC Line Cord Jack 2.2 POWER CONSIDERATIONS Fuse Replace with a 5 Amp, slow-blow type only;

A THREE-TO-TWO WIRE ADAPTER, CREATES A HAZARDOUS

CONDITION. ALESIS CANNOT BE RESPONSIBLE FOR PROBLEMS CAUSED BY USING THE RA-100 OR ANY ASSOCIATED EQUIPMENT WITH IMPROPER AC WIRING. Electrical Service to the RA-100 Although the RA-100 has a maximum audio output rating of 200 watts total into 4Ω, this does not represent the total current consumption since there are certain inefficiencies inherent in linear amplifier design. As a result, the fuse is rated

cramped control rooms typically found in smaller studios; any fan noise

would interfere with the mixing or monitoring process. The RA-100 should be installed so that its heat sinking is allowed to do its job. Please observe the following: • The RA-100 is designed to perform properly over a range of ambient temperatures from 0° C to +50° C (32° F to 122° F), in up to 80% non- condensing humidity. These are not absolute limits, but Alesis cannot guara

amp is mounted.

Avoiding Electromagnetic Interference Because the RA-100 contains a large power transformer, we recommend that you do not: • Place the RA-100 next to an unshielded video monitor, as the magnetic fields may distort the image. • Place tapes, disks, or other magnetic media close to the RA-100. • Play guitar, bass, or any other instrument with magnetic pickups near the RA-100. No damage will occur but AC fields may enter the pickups, caus

• Do not place cables where they can be stepped on. Although stepping on a

cable may not cause immediate damage, it can compress the insulation between the center conductor and shield (thus degrading performance) or reduce the cable’s reliability. • Avoid twisting the cable or having it make sharp, right angle turns. • Never unplug a cable by pulling on the wire itself. Always unplug by firmly grasping the body of the plug and pulling directly outw

With long cable runs (e.g., over 6 meters/20 feet) in noisy electrical

environments, the cable itself can act as an “antenna” and pick up RF fields, AC hum, or other types of interference. To avoid these problems, many professional studios and live sound companies use balanced line connections. The average application will probably not require balanced lines, so try unbalanced connectors first and convert to balanced line operation only if warranted. B

along with ground, into the RA-100. The following diagram shows an

adapter that assumes pin 2 of the XLR connector is “hot.” 1 2 3 (no connection) Female XLR Connector 1/4 inch phone jack shield If pin 3 is hot, then do not connect pin 2 to anything, and connect the wire from the 1/4” phone jack tip to pin 3 of the XLR female connector. If your system uses stereo phone jacks to carry balanced line signals (the tip and ring should carry the in-phase a

Alesis recommends stranded, rather than solid, cables for flexibility and ease

of installation. However, solid cables are equally usable. Never use guitar cords as speaker cables. Because they lack sufficient current- carrying capacity, the amp and speakers will not perform properly and the sound may be degraded. If you make your own cables use electrical zip cord, which is designed to handle several amps of current, or heavy-gauge speaker cable

required that still maintains the great cost/performance ratio of the RA-100's

design. In addition, push connectors are very easy to set up. To connect cable to the push connectors, remove approximately 1/4" of insulation from the end of the wire, being careful not to nick any of the strands. Twist the strands together, press the push terminal button, and feed the strands through the exposed hole in the push connector. Be careful that: • The push connect

Alesis Amplifier Owners Instructions: