SPL performer s800 Operation & User’s Manual

Text of SPL performer s800 Operation & User’s Manual

Mastering Grade Listening

Performer s800 Stereo Power Amplifier PWR PROTECT TEMP VOLTAiR 120V DC Audio Rail Performer s800 – User Manual Stereo Power Amplifier

and thank you for choosing the Performer s800.

The Performer s800 amplifier is an ultra-compact power amplifier that delivers 2 x 285 W to 4 ohms loudspeak- ers. In bridge mode it delivers 450 W into 4 or 8 ohms. VOLTAiR technology is what we also call the SPL 120V Rail Technology within the Professional Fidelity series. This makes the Performer s800 an outstandig device in terms of dynamic range, signal-to-noise ratio and headroom delivering an

SPL performer s800 Rear view (Stereo Mode)

6 Rear view (Bridge Mode) 7 VOLTAiR – 120V Rail Technology 8 Comparisons 9 Inputs 11 Slave Thru 12 Trim 12 Bridge Mode 12 Speaker outputs 13 Bridge Mode 14 Protection circuits 15 DC Protection 15 Overheating protection circuit 15 AMP CTL (Amplifier Control) 16 Specifications 17 Line Inputs & Line Outputs 17 Speaker outputs 17 Output power 17 Output voltage 18 Output impedance 18 Damping facto

Read thoroughly and follow the instructions as well as the security advices of the Quickstart

which is enclosed in the scope of delivery! You can also download the Quickstart here. By pressing the -Button you get to the table of contents. By pressing the -Button you get to the front view of the unit. By pressing the -Button you get to the rear view of the unit. By pressing the -Button you get to the previous content.

Stereo Power Amplifier

PWR PROTECT TEMP VOLTAiR 120V DC Audio Rail Power LED 1
Rear view (Stereo Mode) Voltage Selection: Fuse: 1. Remove Fuse Holder 2. Exchange Fuses 3. Flip Over 4. Reinstall AVIS: RISQUE DE CHOC ÉLECTRIQUE • NE PAS OUVRIR RISK OF ELECTRIC SHOCK D O N O T O P E N CAUTION XLR WIRING Pin 1 = GND Pin 2 = Hot (+) Pin 3 = Cold (–) Minimum Load: 4Ω Minimum Load: 4Ω Minimum Load: 8Ω Serial Number Made in Germany ~ 115V AC / ~230V AC, 50 Hz / 60 Hz, P max. 855VA Mono 3,5mm Jack INPUT L INPUT L AMP CTL AMP CTL

Rear view (Bridge Mode)

Bridge Mode Bridge Mode Voltage Selection: Fuse: 1. Remove Fuse Holder 2. Exchange Fuses 3. Flip Over 4. Reinstall AVIS: RISQUE DE CHOC ÉLECTRIQUE • NE PAS OUVRIR RISK OF ELECTRIC SHOCK D O N O T O P E N CAUTION XLR WIRING Pin 1 = GND Pin 2 = Hot (+) Pin 3 = Cold (–) Minimum Load: 4Ω Minimum Load: 4Ω Minimum Load: 8Ω Serial Number Made in Germany ~ 115V AC / ~230V AC, 50 Hz / 60 Hz, P max. 855VA Mono 3,5mm Jack INPUT L

VOLTAiR – 120V Rail Technology

VOLTAiR is the synonym for our 120V Rail Technology within the Professional Fidelity series. The audio signals are processed with an unequalled +/-60V DC, which corresponds to twice that of discrete operational amplifiers and four-times that of semiconductor operational amplifiers. VOLTAiR Technology reaches outstanding technical and sonic performances. Technically especially in terms of dynamic range and headroom and son

These diagrams show how our VOLTAiR Technology compares to other circuits.

The direct relation between operating level and maximum level is fundamental for the classification: the higher the operating level, the higher the maximum level a circuit can handle. And since virtually all essential acoustic and musical parameters depend on this relation, a higher operating voltage also has a positive impact on the dynamic range, distortion limit and

SPL performer s800 Do bear in mind that dB scales do not represent linear but rather exponential increases. A 3 dB increase corre-

sponds to doubling the acoustic power, +6 dB correspond to twice the sound pressure level, and +10 dB corre- spond to twice the perceived loudness. When it comes to volume, the VOLTAiR Technology exhibits a performance, in regard to maximum level and dynamic range, that is twice that of common components and circuits given that its values a

The Performer s800 is equipped with XLR inputs (8, 12) for balanced connection to a pre-

amp. Full output power (2 x 285 W RMS into 4 ohms or 2 x 185 W RMS into 8 ohms) is per- formed at +6 dBu at the input. For unbalanced connection with e.g. RCA output connect Pin 3 to Ground in the external connector. Made in Ger INPUT R INPUT R DE (–) SPEA – 0 - 5 . 5 - 5 - 4 . 5 - 4 - 3 . 5 - 3 - 2 . 5 - 2 - 1 . 5 - 1 - 0 . 5 T R I M T H R U I N P

The input is passively fed to the SLAVE THRU (9, 13) output for bi-wiring applications.

Trim The input can be lowered with the TRIM switch (10, 14) from 0 dB to -5.5 dB in 0.5 dB steps. This is helpful if you want to use multi speaker sets or speakers in a bi-wiring applica- tion. It allows to level speakers with different efficiency to equal loudness. Bridge Mode In bridge mode only the left input is used. The right input and the trim switch

You can connect 4 or 8 ohms loudspeakers to the speaker outputs

(11, 15). You can either use the ø4 mm cable hole (screwable) or the banana plugs of the gold-plated loudspeaker binding posts. Make sure not to mix up the polarity of the loudspeaker outputs. Voltage Selection: Fuse: 1. Remove Fuse Holder 2. Exchange Fuses 3. Flip Over 4. Reinstall Minimum Load: 4Ω Serial Number Made in Germany ~ 115V A INPUT R INPUT R SPEAKER OUTPUT R

SPL performer s800 The Performer s800 can be operated in bridge mode to combine both channel amps for maximum power (450 W

RMS into 4 or 8 ohms). Only use the left input then. • Set the BRIDGE MODE (7) switch to ON. Warning: Power down the Performer s800 with the mains switch (5) before you activate the BRIDGE MODE switch. In bridge mode you only connect a single loudspeaker to the Performer s800 power amplifier. Use the positive binding post (+) of the left

The Performer s800 has protection circuits against DC (direct current) voltage at the output and against

overheating. DC Protection If DC is detected at the outputs, the Performer s800 automatically switches off. DC voltage can be an indication for a defective power stage. The PROTECT LED (2) on the front indicates that the protection circuit is activated and the power stage has been switched off. The Performer s800 does not automati

AMP CTL (Amplifier Control)

If you use the Performer s800 via AMP CTL with a SPL Phonitor x or SPL Director as a pre- amp, the Performer s800 can be switched between standby and operation together with the Phonitor x or the Director. Therefore you only have to connect the AMP CTL jacks (6) with a 3,5 mm mono mini jack cable. Voltage Selection: Fuse: 1. Remove Fuse Holder 2. Exchange Fuses 3. Flip Over 4. Reinstall AVIS: RISQUE R D Minimum Load: 4Ω

SPL Amplifier Owners Instructions: