Miele PT 7135 C Installations Plan

PT 7135 C To avoid the risk of accidents or damage to the machine, it is essential to read operating and installation instructions before installation and commissioning This prevents both personal injury and damage to the machine. en - GB 10 145 320 / 01 ...

Legend: Connection required Connection optional or required, depending on model AL Vented KLZ Cooling air ASK Condensate drain hose PA Equipotential bonding B Machine anchors SLA Peak-load connection EL Electrical connection UG Box plinth F Machine feet, adjustable UO Open plinth KG Payment system WTV Washer-dryer stacking kit KGA Payment system connection XKM Communication module KLA Cooling air ZL Air intake All rights reserved. 12/14/4 ...

PT 5135/7135  = standard,  = optional, + = only on request, - not available 8 10 145 320 / 01 Technical data PT 5135 C PT 7135 C Drying system Condensation Condensation Drum volume l 130 130 Load capacity kg 6.5 6.5 Door opening diameter mm 391 391 Electrical connection (EL) Standard voltage 2N AC 400V 2N AC 400V Frequency Hz 50 50 Total rated load kW 3.68 3.68 Fuse rating (B trip rating according to EN 60898) A 2 x 10 2 x 10 Supply lead min. cross-section mm² 4 x 1.5 4 x 1.5 Supply lead (H05RN-F) without plug for hard-wired connection   Length of supply lead mm 2000 2000 Alternative voltage (convertible by Service) 1N AC 230V 1N A ...

 = standard,  = optional, + = only on request, - not available 10 145 320 / 01 9 Technical data PT 5135 C PT 7135 C Standard voltage (FIN only) - 2N AC 400 V Frequency Hz - 50 Total rated load kW - 3.68 Fuse rating (B trip rating according to EN 60898) A - 2 x 10 Supply lead min. cross-section mm² - 4 x 1.5 Supply lead without plug for hard-wired connection -  Length of supply lead mm - 2000 Alternative voltage (convertible) 1N AC 230 V Frequency Hz - 50 Total rated load kW - 3.68 Fuse rating (B trip rating according to EN 60898) A - 1 x 16 Supply lead min. cross-section mm² - 3 x 1.5 Alternative voltage (convertible) 1N ...

PT 5135/7135  = standard,  = optional, + = only on request, - not available 10 10 145 320 / 01 Technical data PT 5135 C PT 7135 C Installation on machine feet (F) No. of machine feet No. 4 4 Machine foot, height-adjustable with thread mm +14.5 / -7 +14.5 / -7 Machine foot diameter mm 40 40 Anchoring (B) Standard anchoring Floor anchor kit (for 2 machine feet)   Wood screws according to DIN 571 mm 6 x 50 6 x 50 Rawl plugs (diameter x length) mm 8 x 40 8 x 40 Anchoring of Miele plinths Miele plinth installation (fasteners included)   Required anchor points No. 4 4 Wood screws according to DIN 571 mm 8 x 65 8 x 65 Rawl plugs (dia ...

 = standard,  = optional, + = only on request, - not available 10 145 320 / 01 11 Options / Accessories: Features Box plinth (UG) Box plinth, H 300 mm (UG 5005) Galvanised plinth, stainless-steel sides Box plinth, H 470 mm (UG 5005-47) Galvanised plinth, octoblue stove-finished side panels Box plinth, H 750 mm (UG 5005-75) Galvanised plinth, octoblue stove-finished side panels Open plinth (UO) Open plinth, H 300 mm (UO 5005) Galvanised plinth, octoblue stove finish Open plinth, H 470 mm (UO 5005-47) Galvanised plinth, octoblue stove finish Washer-dryer stacking kit (WTV) Stainless-steel kit (WTV 5062) Washer-dryer stacking ki ...

PT 5135/7135 12 10 145 320 / 01 Installation and planning notes Installation requirements: Electrical connection should only be made to a power supply provided in accordance with all appropriate local and national legislation and regulations. In addition, all regulations issued by the appropriate utilities as well as standards relating to occupational safety, and all applicable valid regulations and technical standards must be observed! General operating conditions Ambient temperature in installation room: +2 °C to +35 °C. This machine should not be operated in the same room as dry- cleaning equipment using perchloroethylene or solvents conta ...

10 145 320 / 01 13 The machine should be levelled in both directions with the aid of the adjustable feet. The anchors provided can be used to bolt the machine to the floor by both front feet. The material provided is intended for use in bolting the machine to a concrete floor. Bolts and fasteners for all other floor types must be provided on site. Plinth installation The machine can be installed on a machine plinth (open or box plinth, available as an optional Miele accessory) or on a concrete platform to be provided on site. The quality of the concrete and its strength must be assessed according to the machine load. Ensure that an ...