Ramsa Ramsa WR-DA7 Service Manual

Text of the manual

Power requirement :

AC 220 – 240 V 50 Hz Power consumption : 105 W (with options) Frequency response : 20 Hz - 20 kHz, +1 dB - –2 dB T.H.D. (total harmonic distortion) : Less than 0.1 % (input = +10 dB/1 kHz, output = +4 dB/RL 600 Ω) Equivalent input noise : –128 dB (Rs = 150 ΩInput sensitivity = –60 dB typical) Residual no

This service information is designed for experienced repair technicians only and is not designed for use by the

general public. It does not contain warnings or cautions to advise non-technical individuals of potential dangers in attempting to service a product. Products powered by electricity should be serviced or repaired only by experienced professional te

0 - 14,400 samples/0 - 300 ms (Fs = 48 kHz), 0 - 326 ms (Fs = 44.1 kHz)

Phase : normal/reverse (switchable) Stereo meter : Bar graph type LED, Left and Right, 20 points for each VU or PPM (selectable), Peak hold on/off, ∞ Fader : 100 mm motor fader ( x 21), +10 db - –90 dB –∞dB Display : LCD, 320 x 240 dot, with backlight Memory : SCENE MEMO

AUX SEND 1/2 :

In/Out : Out Format : IEC 958 Consumer (S/PDIF) Level : 0.5 V [pp]/75 Ω Connector : RCA pin jack WORD CLOCK IN : In/Out : In Level : TTL/75Ωswitchable Connector : BNC WORD CLOCK OUT/THROUGH : In/Out : Out Level : TTL/75 Ω, Pass-through (75 ΩOFF) or termination (75 ΩON) Connector : BNC MIDI IN : In/Out : In Format : MIDI Connector :

WR-ADDA (A-D/D-A Card (8 in / 8 out))

Input 1 - 8 (balanced) Indicated impedance : 10kΩ Nominal source impedance : 50Ω~ 600Ω Nominal input level : +4dB (1.23V) Maximum input level before clipping : +18dB (6.15V) Connector type : D-sub 25P Output 1 - 8 (balanced) Indicated impedance : 10kΩ Nominal source impedance : 150Ω Nominal input level : +4dB (

Major Operating Controls and Their Functions ......................................................................................................

1 Self Check Procedure.............................................................................................................................. 13 Wiring Diagram ....................................

– 1 –

MAJOR OPERATING CONTROLS AND THEIR FUNCTIONS /CURSOR 16 BUS 2 BUS 4 BUS 6 BUS 8 32 MONITOR A MONITOR B SOLO MONITOR 2TR A L/R MONITOR A L/R 2TR B AUX AUX MONO LEVEL PRE ON / OFF FADER CONTROL 1 2 5 6 3 4 BUS ASSIGN PAN 1 2 7 4 3 6 8 DIRECT L/R ON ON 5 PAN /ASSIGN / AUX DYNAMICS / DELAY EQUALIZER MASTER DISPLAY H HM LM ON L EQ Q FREQ GAIN R L +

– 2 –

Fader MIC/LINE INPUT knob PEAK/SIGNAL LED LED field indicators for AUX 1-6, and automation parameters, CH, EQ, PANASSIGN/SURR, LIBRARY and SEL/MAN SOLO LED button FLIP LED button SELECT LED button On LED button Channel Fader Strip AUX/BUS Layer function Channel Fader Strip 1 Channel numbers There are sixteen Channel Fader Strips on the DA7. Dependi

– 3 –

EQUALIZER Section EQUALIZER Section There are three parameter knobs and four frequency range LED buttons in the EQUALIZER section, which are used to change the EQ settings of the currently selected channel. The EQ ON LED button toggles the EQUALIZER on (green) and off. When the controls are active, adjustments can be made to the currently selected

More Ramsa Music Mixer Owners Instructions: