MyGate strike Installation Manual
Read Online
Read the MyGate strike Installation Manual online using the built-in PDF viewer.
Key Pages of Document
This manual contains important safety information. An incorrect installation or an improper use may cause serious damages to persons or objects. Read this manual carefully and completely. Pay particular attention to the sections marked by the symbol: This indicates that risk to personal injury may occur if not adhered to. Store this manual safety for future use. Always disconnect main power supply before opera ...
Power supply Current Motor power Capacitor Thermic Protection Maximum thrust Class IPProtection Revolutions (speed) Opening speed Gate maximum weight Duty Cycle STRIKE 5 STRIKE 8 STRIKE 4 STRIKE 5 110V STRIKE 8 110V 2.3 DIMENSIONS 2.1 PACK CONTENTS 1 Strike Gear motor 2 MPIS04 Anchor plate 3 MVI0510B2 Screw 5x10 for cover 4 MVI1060AZ Screw 10x60 ...
Before the installation, to ensure correct working of the automation, please check the followings: • Make sure the gate’s structure is suitable to be automated • Check the weight, dimensions and type of the gate is appropriate to this type of automation • Ensure the gate is able to open and close smoothly and is free of obstacles that may cause the gate to potentially derail • Check the ...
177+ 50 mm 260 177 32 4 3.4 PRELIMINARY INSTALLATION WORK AND MASONRY FOR ANCHOR PLATE Identify approximately the place of each component and proceed as follows: a) Dig the foundation pit for the gear motor whilst considering the anchor plate dimensions. Give an extra 5cm area extra on each side. Pay attention to measurements shown in Fig.2. b) Provide one or more ducts for the electrical cables so that they ...
a) Lift up the motor cover. b) Insert the four hexagon-headed screws with the washers and nuts in the loops of the motor base (Fig. 4). c) Route the electrical cables in the purpose fabricated hole of the motor base (Fig. 5) and gently lower the motor base onto the anchor plate. d) Move the screws in the loop’s centre and screw them up till the lower nut rests on the anchor ...
f) Repeat the same procedure until the gate is fully covered. g) In case the last section of rack partially comes out from the rack edge, do not cut it. Add a bracket as a gate extension to support the last bit of rack (Fig. 8). h) To avoid the gates weight being supported by the motors drive pinion cog, adjust the four screws to lower a little the gea ...
a) Identify closing and opening brackets according to the motor position against the gate (Fig. 12). b) Manually close the gate up to 3cm before the closing mechanical stop. c) Place the closing bracket on the rack and slide it until the limit-switch is activated (Fig. 13). d) Mark the bracket position onto the rack, slightly open the gate and fix the bracket to the rack. e) Manuall ...
Insert the electrical cables into the control panel’s case by piercing the rubber membrane and place the cable grommet in its purpose fabricated seat on the motor’s base (Fig. 16). Terminate the cable of the main supply with the provided cable block (Fig. 17). Follow the control panel’s instruction manual to proceed with the correct cable wiring. Wire all cables for the earth system to t ...
Tel. +39 0173 210111 - Fax +39 0173 210199 - www.mygateautomation.com 9 Fig. 19 Fig. 19A 6. RELEASE PROCEDURE FOR MANUAL OPERATION 7. MAINTENANCE Check the correct working of the automation at least twice a year, pay particular attention to the safety devices, the torque force produced, the release system for manual operation and to all the mechanical moving parts. Any components dis ...
Related Devices for MyGate strike:
Q71B Q71A 230V ac Control panel for swing gate automation 230Vac powered – double or single leaf • Streamlined programming procedure • Automatic setting o Usage and setup manual for the MyGate Q71B Control Panel. The manual contains instructions for compatibility information, service contacts, wiring setup.
PTP45 PTP45 20 - PTP45 30 - PTP45 50 PTP45 50M Automation for blinds and awnings Installation manual rev01_21 Quick start guide for the MyGate PTP45 Series Home Automation. It details device setup and device operation tips, safety information, software installation, maintenance procedures.
The MyGate Q71A Control Board Installation Manual : Printed 06/11/2012 14:18 1 Q71A 230V Control Board Swing Gate – Double Leaf Instruction Guide TECHNICAL FE Device instruction manual for the MyGate Q71A Controller. This manual describes setup, usage, and device operation tips, assembly reference, operational procedures, safety precautions.
The MyGate Q71B Control Board Installation Manual : Printed 06/11/2012 14:25 1 Q71B 230V Control Board Swing Gate – Double Leaf Instruction Guide TECHNICAL FE Setup instructions for the MyGate Q71B Control Panel. The guide covers usage and shutdown procedures, repair references, adjustment procedures, startup procedures.
AUTOMAZIONI PER CANCELLI A BATTENTE AUTOMATISMES POUR PORTAILS A BATTANTS AUTOMATION FOR SWING GATES AUTOMATISIERUNG FÜR FLÜGELTORE AUTOMATIZACIONES PARA VERJ Instructions for safe usage of the MyGate myHook Series Gate Opener. It explains installation, setup, and troubleshooting, functional overview, technical guidelines, service instructions.
Q71S Q71S CONTROL PANEL FOR SLIDING GATES Control panel for sliding gate automation 230Vac • Streamlined programming procedure • Automatic setting of the ob User documentation for the MyGate Q71S Control Panel. This guide elaborates on device features and software configuration, product handling, usage examples.
Garage door opener 02/2019 Technical operations guide for the MyGate Kit LIBRA Gate Opener. This manual outlines operating modes, configuration options, hardware instructions.
01_17 myAster AUTOMATION FOR SWING GATES Installation manual Instruction and usage manual for the MyGate myAster 3 Gate Opener. This documentation explains configuration and power requirements, software configuration, software installation, installation guides.
Garage Door Opener: Frequently Requested PDF Instructions
8 8 17 6 5 8 7 0 0 27 9 INSTALLATION AND USER’S MANUAL INSTRUCTIONS D’UTILISATION ET D’INSTALLATION INSTRUCCIONES DE USO Y DE INSTALACION ISTRUZIONI D’U Comprehensive instruction manual for the BFT LUX Garage Door Opener. It provides technical information on service contacts, network configuration, device safety checks.
Device setup manual for the Chamberlain GARAGE DOOR OPENER CG40D 1/2 HP Garage Door Opener. It provides information on safety and device instructions, technical guidelines, connectivity options, device features.
Serial Number: Date of Purchase: Chain Drive Garage Door Opener The Chamberlain Group, Inc. 845 Larch Avenue Elmhurst, Illinois 60126-1196 www.liftmaster.com . Product operation manual for the Chamberlain 8360 Garage Door Opener. This reference manual explains troubleshooting tips, power management, device reset instructions, system setup.
TM TM MODEL 1703EML - DER CHAMBERLAIN ARM™ EINBAUANLEITUNGEN zur Benutzung in Verbindung mit der Montageanleitung von Chamberlain Garagentorantrieben Modelle: Operating and setup manual for the Chamberlain MotorLift 1703EML Garage Door Opener. This guide provides technical guidance on compatibility information, hardware components, reset instructions, usage examples.