TKO 9GR Assembly Manual

Text of TKO 9GR Assembly Manual

IMPORTANT SAFETY INSTRUCTIONS

• Read this Owner’s Manual and follow it’s instructions carefully before assembly the machine. Make sure that it is properly assembled and tightened before each use. • Inspect your machine prior to exercise to ensure that all nuts and bolts are fully tightened. • Replace the worn parts immediately. • Most exercise equipment is not recommended for small children. Children should not use the machine unless they ar

BEFORE YOU BEGIN

Note: Before beginning assembly remove all parts and hardware from the carton, ensure you have everything according to the list. THE FOLLOWING TOOLS ARE INCLUDED FOR ASSEMBLY: Handlebar Console Upright Cover Pedal Seat Handlebar Accessory Tray Rear Stabilizer Main Frame Front Stabilizer Back Cushion Cover Back Cushion Seat T-HAND SOCKET WRENCH (17MM) ALLEN WRENCH (M6) SOCKET WRENCH COMBINATION WRENCH

85 Washer (8x38x2.0t)

4 90 90 Lock Washer (M8) 6 95 95 Screw, Round Head (M5xp0.8x15mm) 10 96 96 Screw, Round Head (M5xp0.8x50mm) 2 104 104 Bolt, Socket Head (M8xp1.25x50mm) 2 109 109 Bolt, Hex Head (M8xp1.25x65mm) 4 114 114 Bolt, Hex Head (M10xp1.5x50mm) 2 131 131 Screw (M4x10mm) 4

Back Cushion Bracket

1 6 Back Cushion Frame 1 7 Seat Frame 1 8 Upright Post 1 9 Upper Handlebar 1 10 Front Left-Side Cover 1 11 Front Right-Side Cover 1 12 Crank Cover 2 13 Rear Left-Side Cover 1 14 Rear Right-Side Cover 1 15 Left Pedal 1 16 Right Pedal 1 17 Console Display 1 18 Console Bracket 1 19 Console Lower Case 1 20 Battery Door 1 21 Front De

Quick-Access Key Base (-)

1 37 Square Plug (30x60mm) 1 38 End Cap (50x100mm) 4 39 Leveler (ψ50) 4 40 Transport Wheel 2 41 Generator 1 42 Belt (584mm J8) 1 43 Pulley (120mm) 1 44 Magnet 1 45 Pulley (235mm) 1 46 Belt (1059mm J8) 1 47 Seat Rail End Cap 2 48 Foam Grip 2 49 Front Aluminum Upright Cover 1 50 Rear Aluminum Upright Cover 1 51 Cushion Adjustment Lever 1 52 Back Cushion Adjustment Bracket 1 53 Cushion Torsion Spring 1 54 Cus

Seat Linkage Spacer

1 79 Eye Bolt (40mm) 2 80 Eye Bolt (50mm) 4 81 Tension Bracket 2 82 Square Key (6×6×15mm) 1 83 E Clip 2 84 Crescent Ring 4 85 Washer (8×38×2.0t) 5 86 Washer (10×23×2.0t) 2 87 Washer (17×25×1.0t) 1 88 Washer (18.3×25×1.0t) 1 89 Washer (20×1.0t) 2 90 Lock Washer (M8) 18 91 Screw (M3×10mm) 3 92 Screw (M3×25mm) 4

Bolt, Hex Head (M8×p1.25×75mm)

1 111 Bolt, Hex Head (M8×p1.25×80mm) 4 112 Bolt, Hex Head (M10×p1.5×145mm) 2 113 Bolt, Hex Head (M10×p1.5×144mm) 2 114 Bolt, Hex Head (M10×p1.5×50mm) 2 115 Flange Nut (M5) 2 116 Nut (M6) 3 117 Nut (M8) 4 118 Nylon lock Nut (M6) 4 119 Nylon lock Nut (M8×6.2t) 4 120 Nylon lock Nut (M8) 12 121 Nylon lock Nut (M10) 6 122 Generator Wire (3pin×700mm) 2 123 Extension Wire (5pin×300mm) (Back of

STEP 1 Leveler Installed

a. Attach the Leveler (39) to the Front Stabilizer (2) and the Rear Stabilizer (3) b. Adjust the Leveler (39) then securely tighten the Adjustment Plate (diagram above) STEP 2 Front & Rear Stabilizer Assembly Attach the Front Stabilizer (2) and the Rear Stabilizer (3) to the Main Frame (1) and secure it with 4 Washer (8x38x2.0t) (85) 4 Lock Washer (M8) (90) and 4 Bolts, Hex Head (M8xp1.25x65mm) (109). Tight

STEP 3 – Upright Post Assembly

Slide the Console Bracket (18) and the Upright Sleeve (22) onto the Upright Post (8.) • Make sure the flat side of the Upright Post (8) is facing forward. STEP 4 a. Insert 2 Nylon lock Nuts (M10) (121) into the front of the Main Frame (1) (illustration shown above) b. Slide the Upright Post (8) into the Main Frame (1) and secure it with 2 Bolts, Hex Head (M10xp1.5x50mm) (114), tighten these 2 Bolts using the T-Head Soc

TKO 9GR a. Connect the Extension Wire (124) in the Upright post to the Lower Connection Wire (125)

in the Main Frame. b. Connect the Pulse Sensor Wire in the Upright Post (128) to the Pulse Sensor Wire in the Main Frame (129) c. Make sure the plugs and the sockets are connected and locked securely. d. Install the Front Decorative Cover (21) onto the front of the Main Frame (1) using 2 Screws, Round Head (M5xp0.8x50mm) (96.) e. Attach the TAG Logo to the

STEP 6 – Display Console and Handlebar Assembly

a. Remove the Screw (M3x10mm) (91) in the back on the console using a Philips Screw Driver. b. Remove the Battery Door (20). c. Install the “AA” rechargeable batteries. (4 rechargeable battery are included in the hardware pack). • Please only use the Nickel-Metal Hybrid (NI-MH) rechargeable batteries. NOTE: Using the Regular battery or the wrong type of batteries will damage the console display. ST

a. Connect the Pulse Sensor Wire in the back of the Console (127) to the Pulse Sensor Wire

in the Upright Post (128.) b. Connect the Extension Wire (123) in the back of the Console to the Extension Wire (124) in the Upright Post. STEP 9 Attach the Console (17) to the Main Frame (1) secure it using 4 Screws, Round Head (M5xp0.8x15mm) (95). STEP 10 Slide the Console Bracket (18) up and attached to the back of the Console (17) secure it using 4 Scre

TKO Exercise Bike Owners Instructions: