Toro 30353 Operator's Manual

72in Rotary Mower 62in Rotary Mower 60in Rotary Mower Groundsmaster® 360 Series and 7200 Series Traction Unit Model No. 30353—Serial No. 312000001 and Up Model No. 30354—Serial No. 312000001 and Up Model No. 30456—Serial No. 312000001 and Up Model No. 30457—Serial No. 312000001 and Up Model No. 30481—Serial No. 312000001 and Up To register your product or download an Operator's Manual or Parts Catalog at no charge, go to www.Toro.com. Original Instructions (EN) ...

and maintain your product properly and to avoid injury and product damage. You are responsible for operating the product properly and safely. You may contact Toro directly at www.Toro.com for product and accessory information, help finding a dealer, or to register your product. Whenever you need service, genuine Toro parts, or additional information, contact an Authorized Service Dealer or Toro Customer Service and have the model and serial numbers of your product ready. Write the numbers in the space provided. Model No. Serial No. This manual identifies potential hazards and has safe ...

The following instructions are from the CEN standard EN 836:1997 and ANSI B71.4-2004. This product is capable of amputating hands and feet and throwing objects. Always follow all safety instructions to avoid serious injury or death. Training • Read the Operator's Manual and other training material carefully. Be familiar with the controls, safety signs, and the proper use of the equipment. • Never allow children or people unfamiliar with these instructions to use this equipment. Local regulations can restrict the age of the operator. • Never operate while people, especially children, or pets are nearby. • Keep in ...

– stop the engine and remove the key. • Disengage drive to attachments, stop the engine, and remove the ignition key: – before checking, cleaning or working on the machine; – after striking a foreign object. Inspect the machine for damage and make repairs before restarting and operating the equipment; – if the machine starts to vibrate abnormally (check immediately). • Do not operate the machine under the influence of alcohol or drugs. • Lightning can cause severe injury or death. If lightning is seen or thunder is heard in the area, do not operate the machine; seek shelter. • Disengage drive to attachments wh ...

Decals Safety decals and instructions are easily visible to the operator and are located near any area of potential danger. Replace any decal that is damaged or lost. 112-1461 1. Belt routing 107-2908 1. Thrown object hazard—keep bystanders a safe distance from the machine. 2. Thrown object hazard—do not operate the mower with the deflector up or removed, keep the deflector in place. 3. Cutting/dismemberment hazard of hand or foot, mower blade—stay away from moving parts. 93-7818 1. Warning—read the Operator's Manual for instructions on torquing the blade bolt/nut to 115-149 N-m (85-110 ft-lb). 93-6687 1. Do not step he ...

machine. 2. Cutting/dismemberment hazard of hand, mower blade—stay away from moving parts, keep all guards and shields in place. 3. Cutting/dismemberment hazard of foot, mower blade—stay away from moving parts, keep all guards and shields in place. 6 ...

Description Qty. Use Parts catalog 1 Operator's Manual 1 Certificate of Compliance 1 Review the material and save in an appropriate place: Note: Determine the left and right sides of the machine from the normal operating position. Removing the Existing Mower (if applicable) 1. Park the machine on a level surface with the mower in the fully raised position. Stop the engine, engage the parking brake and remove the key from the ignition switch. Note: When the mower is in the raised position, the pull link torsion spring tension (Figure 2) is reduced making it much easier to disconnect the pull links from the machine. g0172 ...

from the mower gearbox shaft: A. Remove the roll pin from the end yoke and the gearbox shaft (Figure 4). Figure 4 1. Drive shaft 3. Roll pin 2. Capscrews and locknuts 4. Gearbox B. Loosen the (2) capscrews and locknuts (Figure 4). C. Slide the drive shaft end yoke from the gearbox shaft. Note: Raise and tie the drive shaft to the frame. 6. Remove the (4) ring pins and clevis pins that secure the lift chains to the adjustment clevises on the mower (Figure 2). 7. Slide the mower away from the machine. Note: The front of the traction unit may have to elevated to move the mower away from the machine. Instal ...

Cutting unit pitch is the difference in height-of-cut from the front of the blade plane to the back of the blade plane. Toro recommends a blade pitch of approximately 5/16 to 7/16 inch (8 to 11mm). That is the back of the blade plane is 5/16 to 7/16 inch (8 to 11mm) higher than the front. 1. Position the machine on a level surface on the shop floor. 2. Set the mower to the desired height-of-cut, move the throttle lever to the Slow position, stop the engine, set the parking brake, and remove the ignition key. 3. Rotate the center blade so that it points straight forward. 4. Using a sho ...

the 6 inch (15.8 cm) position. 4. Adjust the anti-scalp rollers and skids as required. Adjusting the Skid(s) Mount the skids in the lower position when operating in height of cuts higher than 2-1/2 inches (64 mm) and in the higher position when operating in height of cuts lower than 2-1/2 inches (64 mm). Note: On Guardian® mowers, when the skids become worn, you can switch the skid to the opposite sides of the mower, flipping them over. This will allow you to use the skids longer before replacing them. 1. Disengage the PTO and set the parking brake. 2. Move the throttle lever to the Slow position, stop ...

3. 2-1/2 inches (63 mm) 2. 2 inches (51 mm) 4. 3 inches (76 mm) and higher 5. Install the flange nut bushing, spacer, and bolt. Torque to 40-45 ft-lb (54-61 N⋅m) (Figure 8). Adjusting the Rollers Mount the rollers in the lower position when operating in height of cuts higher than 2-1/2 inches (64 mm) and in the higher position when operating in height of cuts lower than 2-1/2 inches (64 mm). 1. Disengage the PTO, release the traction pedal and set the parking brake. 2. Move the throttle lever to the Slow position, stop the engine, remove the key, and wait for all moving parts to stop before leaving the operating posit ...

1. Bolt 4. Nut 2. Chute-side roller 5. Bracket 3. Spacer Figure 14 Side-discharge Mowers Only 1. Bolt 3. Under-mower roller (2) 2. Roller shaft 4. Bracket 5. Install the fasteners as illustrated. 12 ...

To maintain enough power for the machine and deck while mowing, operate the engine at the fast throttle position and adjust your ground speed for conditions. A good rule to follow is: decrease ground speed as the load on the cutting blades increases; and increase ground speed as load on the blades decreases. Mowing Direction Alternate mowing direction to avoid making ruts in the turf over time. This also helps disperse clippings which enhances decomposition and fertilization. Cutting Speed To improve cut quality, use a slower ground speed. Avoid Cutting Too Low If the cutting width of the mower is wider ...

WARNING If you raise the machine using only a jack to support it while you work under the mower deck, the jack could tip, causing the mower deck to fall, crushing you or bystanders. Always secure the machine with at least 2 jack stands when you have the mower deck raised. CAUTION On the top of the mower deck are two links that connect them to the frame. Connected to these links are torsion spring that are under tension (Figure 15). If you disconnect the link the stored energy in the torsion spring will be released and could cause the links to move, d ...

Maintenance Service Interval Maintenance Procedure After the first 50 hours • Check the tire pressure. • Check the condition of the blade drive belts on the mower. Before each use or daily • Check the mower blades. • Clean the mower. Every 50 hours • Grease the bearing and bushing grease fittings. Daily Maintenance Checklist Duplicate this page for routine use. For the week of: Maintenance Check Item Mon. Tues. Wed. Thurs. Fri. Sat. Sun. Check Safety Interlock Operation Check Grass Deflector in Down Position (if applicable) Check Parking Brake Operation Check Fuel Level Check Tire Pressure Check Instrument ...

Service Interval: Every 50 hours The machine has grease fittings that must be lubricated regularly with No. 2 General Purpose Lithium Base Grease. If the machine is operated under normal conditions, lubricate all bearings and bushings after every 50 hours of operation. Bearings and bushings must be lubricated daily when operating conditions are extremely dusty and dirty. Dusty and dirty operating conditions could cause dirt to get into the bearings and bushings, resulting in accelerated wear. Lubricate the grease fittings immediately after every washing, regardless of interval specified. 1. Wipe the grease ...

improper wash down procedures. Do not wash down the unit when it is still hot and avoid directing high-pressure or high volume spray at the bearings or seals. 17 ...

Service Interval: After the first 50 hours Maintain the air pressure in the front and rear tires. The correct air pressure is 25 psi (172 kPa) in the rear tires and 15 psi (103 kPa) in the front tires. If a cab is installed on the machine, the front and rear tires should be inflated to 25 psi (172 kPa). Uneven tire pressure can cause uneven cut. Check the tires when they are cold to get the most accurate pressure reading. Replacing the Blade Drive Belts Service Interval: After the first 50 hours The blade drive belts, tensioned by the spring loaded idler pulleys, are very durable. However, after many hours of use, the belts w ...

between the sail and flat part of the blade. Eventually a piece of the blade may break off and be thrown from under the housing, possibly resulting in serious injury to you or bystanders. • Inspect the blade periodically for wear or damage. • Never try to straighten a blade that is bent or weld a broken or cracked blade. • Replace a worn or damaged blade. Figure 19 1. Cutting Edge 3. Wear/slot Forming 2. Sail Area 4. Crack Checking for Bent Blades 1. Disengage the PTO, release the traction pedal and set the parking brake. 2. Move the throttle lever to the Slow position, stop the engine, remo ...

Replacement blades made by other manufacturers may result in non-conformance with safety standards. WARNING Contact with a sharp blade can cause serious injury. Wear gloves or wrap sharp edges of the blade with a rag. 1. Hold the blade end using a rag or thickly-padded glove. 2. Remove the blade bolt, anti-scalp plate, and blade from the spindle shaft (Figure 23). Sharpening the Blades WARNING When sharpening blade, pieces of blade could be thrown and cause serious injury. Wear proper eye protection when sharpening blades. 1. Sharpen the cutting edge at both ends of the blade (Figure 21). Maintain the o ...