Toro 4036 Operator's Manual

Greensmaster® 2000 and 2600 Walk-Behind Mower Model No. 04036—Serial No. 311000001 and Up Model No. 04037—Serial No. 311000001 and Up To register your product or download an Operator's Manual or Parts Catalog at no charge, go to www.Toro.com. Original Instructions (EN) ...

directives, for details please see the separate product specific Declaration of Conformity (DOC) sheet. WARNING CALIFORNIA Proposition 65 Warning The engine exhaust from this product contains chemicals known to the State of California to cause cancer, birth defects, or other reproductive harm. This spark ignition system complies with Canadian ICES-002. Introduction This machine is a walk behind, reel-blade l ...

Toro Mower Safety...............................................5 Sound Pressure.....................................................6 Sound Power........................................................6 Vibration (Model 04 ...

EN 836:1997, ISO standard 5395:1990, and ANSI B71.4-2004 specifications in effect at the time of production when the Operator Presence Kit, Part No. 105–5363 is installed. Improper use or maintenance by the operator or owner can result in injury. To reduce the potential for injury, comply with these safety instructions and always pay attention to the safety alert symbol, which means Caution, Warning, or D ...

– disengage the cutting unit and traction drive; – set the parking brake; – stop the engine. • Disengage drive to cutting unit when transporting or not in use. • Stop the engine and disengage drive to cutting unit: – before refuelling; – before removing the grass catcher; – before making height adjustment. – before clearing blockages; – before checking, cleaning or working on the mower; – after striking a for ...

sudden stops and starts. – When near or crossing roads, always yield the right-of-way. – Reduce engine speed and apply the service brake when going downhill to keep forward speed slow and to maintain control of the machine. • Do not touch the engine, muffler, or exhaust pipe while the engine is running or soon after it has stopped because these areas could be hot enough to cause burns. • When a person ...

Safety decals and instructions are easily visible to the operator and are located near any area of potential danger. Replace any decal that is damaged or lost. 93-7348 1. Warning—read the Operator’s Manual. 2. Fire hazard—no fire, open flames, or smoking; when adding fuel to the tank, leave space between the fuel and the top of the tank. 3. Thrown object hazard—keep bystanders a safe distance from the machine. 4. Cut ...

115-1614 1. Warning—read the Operator’s Manual. 3. Thrown object hazard—keep bystanders a safe distance from the machine. 2. Warning—do not operate the machine unless you are trained. 4. Warning—stay away from moving parts; keep all guards in place. 115-1718 1. Brake 4. Parking brake 2. Release the handle to disengage ...

Procedure Description Qty. Use Handle 1 1 Cable tie 2 Install the handle. Lift handle 2 Clamp 4 2 Lock nut 8 Install the lift handles. Kickstand assembly 1 Spring 2 Small spacer 2 Large spacer 2 Large bolt 2 Small bolt 2 Locknut 2 3 Washer 2 Install the kickstand (model 04037 only). Wheel shaft, right 1 Wheel shaft, left 1 4 Transport wheels (obtain separately) 2 Install the ...

Handle Parts needed for this procedure: 1 Handle 2 Cable tie Installing the Handle 1. Remove the bolt, washer, and lockwasher from the mounting pin on each side of the mower (Figure 2). Figure 2 1. Mounting pins 3. Bolt and locknut 2. Handle arms 4. Hairpin cotter and ring pin 2. Remove the bolts and locknuts securing the bottom of the handle arms to each side of the mower (Figure 2). 3. Remove the hairpin cotters and ring pi ...

Parts needed for this procedure: 2 Lift handle 4 Clamp 8 Lock nut Procedure 1. Loosely mount a lift handle to each side of the handle with 2 clamps and 4 locknuts (Figure 4). Figure 4 1. Lift handle 3. Clamp 2. Locknut 2. Position the handles about 6 inches below the control panel (Figure 4). Tighten the mounting nuts. Note: The lift handles may be relocated for operator comfort. 3. Secure the control cables to the handle, below ...

3. Spring 7. Large spacer 4. Small bolt 8. Locknut 6. Place a nut runner over the end of the spring pointing towards the rear and move the end of the spring over and under the kickstand spacer (Figure 6). Figure 6 1. Nut runner 3. Move the spring end under the kickstand spacer 2. Spring 4. Spring end under frame 4 Installing the Transport Wheels Parts needed for this procedure: 1 Wheel sha ...

onto axle and locking clip is secured in groove on axle shaft. 8. Repeat procedure on opposite side of machine. 9. Inflate the tires to 12 to 15 psi. (574 to 718 Pa). 5 Adjusting the Cutting Unit No Parts Required Procedure Before operating the machine, complete the following adjustments: • Level the rear drum to the reel. • Adjust the bedknife to the reel. • Adjust th ...

4. Service brake 2. Throttle control 5. Parking brake 3. On/off switch Traction Drive Lever The traction drive lever (Figure 10) is located on the front right side of the control panel. It has two positions: Neutral and Forward. Pushing the lever forward engages the traction drive. Throttle Control The throttle control (Figure 10) is located on top right side of the control panel. The lever connec ...

the engine. The lever has two positions: Run and Choke. Move the lever to the Choke position when starting a cold engine. After engine starts move lever to Run position. Figure 13 1. Choke lever 2. Fuel shut off valve Fuel Shut-Off Valve The fuel shut off valve (Figure 13) is located on left front of engine. The valve has two positions: Closed and Open. Move the lever to the closed positio ...

machine from the normal operating position. Think Safety First Please carefully read all of the safety instructions and decals in the safety section. Knowing this information could help you or bystanders avoid injury. Checking the Engine Oil Level Check the engine oil level before each use or every 8 operating hours, refer to Checking the Engine Oil Level in Engine Maintenance (page 22). Filling the ...

electricity can be released causing a spark which can ignite the gasoline vapors. A fire or explosion from gasoline can burn you and others and can damage property. • Always place gasoline containers on the ground away from your vehicle before filling. • Do not fill gasoline containers inside a vehicle or on a truck or trailer bed because interior carpets or plastic truck bed liners may insulate the c ...

push the mower forward, and then lower the rear of mower onto the transport wheels. 3. Ensure that the traction and reel drive controls are in the Disengaged position and start the engine. 4. Set the throttle control to Slow, raise the front of the machine up slightly, gradually engage the traction drive and slowly increase the engine speed. 5. Adjust the throttle to operate the mower at the desired groun ...

Recommended Maintenance Schedule(s) Maintenance Service Interval Maintenance Procedure After the first 8 hours • Change the engine oil. After the first 25 hours • Clean the fuel filter. Before each use or daily • Check the interlock switch operation. • Check the engine oil level. Every 25 hours • Grease the machine. (Grease the fittings immedia ...

Important: Duplicate this page for routine use. For the week of: Maintenance Check Item Mon. Tues. Wed. Thurs. Fri. Sat. Sun. Check the safety interlock operation. Check the parking brake operation. Check the fuel level. Check the engine oil level. Check the air filter. Clean the engine cooling fins. Check for unusual engine noises. Check for unusual operating noises. Check the reel-to-bedknife adjustment. Check the height-of-cu ...