Toro 30827 Operator's Manual

Text of the manual

Form No. 3329–577 Rev B

27� Rotary Cutting Deck Groundsmaster� 3500, 4500/4700 Traction Unit Model No. 30827—230003001 and Up

All Rights Reserved

Printed in the USA � 2003 by The Toro Company 8111 Lyndale Avenue South Bloomington, MN 55420-1196 Contents Page Introduction 2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Safety 3 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Safety and Instruction Decals 3 . . . . . . . . . . . . . .

Safety and Instruction Decals

Safety decals and instructions are easily visible to the operator and are located near any area of potential danger. Replace any decal that is damaged or lost. 98-7818 1. Warning—torque the blade bolt to 85–110 ft.-lb (115–149 N⋅m). Read the operator’s manual for further instructions. 43-8480 104-1086 1. Heigh

Note: Specifications and design subject to change without

notice. General Specifications Chamber Construction Welded 7 GA (.1793 in.),10 GA (.1345 in.) and 12 GA (.1036 in.) steel. Spindle support is 3/16 in. high-strength steel and 10 GA exterior channels, withstands multiple blade impact tests. Deck frame is welded 1-1/2 in. square tubing

34 in. (86.4 cm)

Overall width 34 in. (86.4 cm) Overall height 9.6 in. (24.4 cm) to carrier mount 10-1/2 in. (26.7 cm) at 3/4 in. height of cut 13-3/4 in. (34.9 cm) at 4 in. height of cut Roller footprint Front to back Rear roller Front rollers 29.5 in. (74.9 cm) 29.8 in. (75.7 cm) full length 18.5 in. (47 cm) between front roller

Note: Determine the left and right sides of the machine from the normal operating position.

Loose Parts Note: Use this chart as a checklist to ensure that all parts have been received. Without these parts, total setup cannot be completed. Description Qty. Use Decal 1 Apply to cutting deck for CE Parts Catalog 1 Operator’s Manual 1 Read before opera

Adjusting the Height of Cut

Important This cutting deck often cuts approximately 1/4 inch lower than a reel cutting unit with the same bench setting. It may be necessary to have these rotary cutting deck’s bench set 1/4 inch above that of reels cutting in the same area. Important Access to the rear cutting units is greatly improved by removing the cutt

Installing the Mulching Baffle

(Optional) 1. Thoroughly clean debris from mounting holes on rear wall and left side wall of chamber. 2. Install mulching baffle in rear opening and secure with 5 flange head screws (Fig. 5). 1 m–5421 Figure 5 1. Mulching baffle 3. Verify that mulching baffle does not interfere with either tip of blade and does not protrude

Note: Determine the left and right sides of the machine

from the normal operating position. Operating Tips Blade Selection Standard Angled Sail The blade generally performs best in lower heights of cut (3/4 to 2–1/2 inch). The optional high lift parallel sail blade performs better in the higher heights of cut (2 to 4 inch). Attributes: • Disc

Optional Equipment Configuration

Standard Angle Sail Blade High Lift Parallel Sail Blade DO NOT USE WITH MULCHING BAFFLE Mulching Baffle Roller Scraper tion Grass Cutting: .75 to 1.75 inch Height of Cut Recommended in most applications May work well in light or sparse turf Has been shown to improve dispersion and after cut perfor- mance on northern grasse

Other Lawn Mower Manuals