Systium Technologies 545 Assembly Manual

Copyright © 2010, Systium® Technologies, LLC PN: 91004-03 Radio Frequency Interference Notice (USA) This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interfere ...

Copyright © 2010, Systium® Technologies, LLC PN: 91004-03 ASSEMBLY GUIDE Assembly Safety Instructions Assembly of a computer system using this product shall be assembled only by technically qualified personnel. Follow the instructions in the document “Model 545 Maintaining Regulatory Compliance” to meet and maintain the safety and product regulatory compliance of this product when assembling a computer system using this product. WARNINGS Read and adhere to all of these instructions and instructions supplied with this assembly. Failure to follow these instructions will result in void ...

Copyright © 2010, Systium® Technologies, LLC PN: 91004-03 BULK PACKAGE Please re-cycle the packaging. None of the bulk pack packaging is designed for reuse when shipping to the end customer. CONTENTS The Model 545 MotherBoard Ready System product contains the following: • Model 545 Chassis with Power Supply Installed • North American Compliant Power Cord • Integration Kit • Quickstart Guide. (This manual must be included in shipment to the End User.) • Manual Removing a Side Cover 1. Remove the plastic bag protecting the chassis. Save the bag for shipping the assembled computer ...

Copyright © 2010, Systium® Technologies, LLC PN: 91004-03 4. Place the bezel to the side where it will not get scratched or damaged before reassembly. Installing the I/O Shield 1. Locate the I/O shield supplied with the motherboard. 2. Place the lower surface of the I/O shield in the I/O opening in the rear of the chassis. Ensure the I/O shield is fully inserted into the opening. Refer to Figure 6 3. Carefully press the top surface of the I/O shield into the I/O opening. Be careful to only place pressure at the outer edges of the I/O shield when pressing on the I/O shield. Check that the ...

Copyright © 2010, Systium® Technologies, LLC PN: 91004-03 Installing a I/O Adapter (Optional) If an I/O adapter is part of the system configuration the following instructions should be followed. If no I/O adapter is to be installed, then this section can be skipped. 1. Remove the screw holding the I/O slot cover for the I/O slot to be used. Refer to Figure 8 for the location of the I/O slot covers. 2. To completely remove the I/O slot cover, slide the cover upwards and away from the back of the chassis. 3. Refer to the I/O adapter manual for any installation or configuration steps that n ...

Copyright © 2010, Systium® Technologies, LLC PN: 91004-03 4. Install the second mounting rail on the opposite side of the peripheral. 5. If the 5.25” external peripheral is being installed in the middle bay you must first remove the EMI shield built in to the chassis. The EMI shield can be removed by inserting a flat blade screwdriver into the hook in the EMI shield. The shield can then be rotated carefully to break the mounting clips. Completely remove the EMI shield from the chassis and dispose of the EMI Shield. Refer to Figure 15 6. Line up the mounting rails with the corresponding ...

Copyright © 2010, Systium® Technologies, LLC PN: 91004-03 Installing a 5.25” External Peripheral (Lower Bay) NOTE It is recommended that the lower bay only be used for an external peripheral after the middle and top bays have been used. The lower bay uniquely supports internal or external peripherals. 1. Configure any jumpers or switch settings required by the peripheral. Refer to the peripheral's user manual for specific instructions. 2. Remove the built-in EMI shield by placing a flat blade screwdriver in the hook on the front of the shield. The shield can then be rotated carefully t ...

Copyright © 2010, Systium® Technologies, LLC PN: 91004-03 NOTE The 3.5" peripheral carrier supports two 1" high devices or one 1.6' high device. For a second 1" high peripheral please repeat steps 3 and 4 before installing the assembly into the chassis. Connect Peripheral Cables 1. Connect the cables supplied with the motherboard and/or installed peripheral devices. Care should be given to ensure the cables do not block airflow within the chassis and are routed cleanly to facilitate future system maintenance. Refer to assembly instructions for the specific motherboard being installed for ...

Copyright © 2010, Systium® Technologies, LLC PN: 91004-03 Install Side Cover NOTE Before installing the right side cover please check that all cables are connected and no tools, screws or accessories are left inside the chassis. 1. Position the lower groove in the side cover to fit onto the lower edge of the chassis. Refer to Figure 21. 2. Close the side cover so as to be flush with the chassis. 3. Slide the cover towards the front of the chassis. Ensure that all the mounting clips on the cover are fully engaged with the chassis. If the optional locking tab is installed, ensure that the ...

with the motherboard. Refer to the main assembly guide for instructions on installing the I/O shield. Installing the Motherboard STANDOFF INSTALLATION No additional standoffs are required. INSTALLATION OF FRONT PANEL CONNECTORS ITOX GCB60-BX ASSEMBLY INSTRUCTIONS Copyright © 2007, Systium Technologies, LLC PN: 91260-00 SySTIUMTM TECHNOLOGIES MOTHERBOARD READY SM SYSTEM • MODEL 545 ...

with the motherboard. Refer to the main assembly guide for instructions on installing the I/O shield. Installing the Motherboard STANDOFF INSTALLATION The S3000AH does not require installation of the brass stand-offs included in the integration kit. These parts can be disposed of. HEATSINK INSTALLATION 1. Install the CPU following the instructions provided with the CPU. 2. Insert the heat sink support bracket into the motherboard from the underside of the motherboard. The standoffs on the bracket are inserted into the holes in the motherboard. Refer to Figure 2 NOTE Make sure ...

supplied with the motherboard. Refer to the main assembly guide for instructions on installing the I/O shield. Installing the Motherboard STANDOFF INSTALLATION Install two brass standoffs, included in the chassis integration kit, in the locations shown in the figure 1 below. HEATSINK INSTALLATION 1. Install the CPU following the instructions provided with the CPU. 2. Insert the heat sink support bracket into the motherboard from the underside of the motherboard. The standoffs on the bracket are inserted into the holes in the motherboard. Refer to Figure 2 FIGURE 2 NOTE Make sure t ...

with the motherboard. Refer to the main assembly guide for instructions on installing the I/O shield. Installing the Motherboard STANDOFF INSTALLATION Install one brass standoff, included in the chassis integration kit, in the location shown in the figure below. MOTHERBOARD INSTALLATION Be careful installing the motherboard making sure none of the I/O shield tabs get bent or damaged. INSTALLATION OF FRONT PANEL CONNECTORS ITOX G4V-620B(N) ASSEMBLY INSTRUCTIONS Copyright © 2003, Systium Technologies, LLC PN: 91136-00 SySTIUMTM TECHNOLOGIES MOTHERBOARD READY SM SYSTEM • MODEL 545 ...

the motherboard. Refer to the main assembly guide for instructions on installing the I/O shield. Installing the Motherboard STANDOFF INSTALLATION Install two brass standoffs, included in the chassis integration kit, in the locations shown in the figure 1 below. HEATSINK INSTALLATION 1. Install the CPU following the instructions provided with the CPU. 2. Insert the heat sink support bracket into the motherboard from the underside of the motherboard. The standoffs on the bracket are inserted into the holes in the motherboard. Refer to Figure 2 FIGURE 2 NOTE Make sure the top surfac ...

the motherboard. Refer to the main assembly guide for instructions on installing the I/O shield. Installing the Motherboard STANDOFF INSTALLATION Install two brass standoffs, included in the chassis integration kit, in the locations shown in the figure 1 below. HEATSINK INSTALLATION 1. Install the CPU following the instructions provided with the CPU. 2. Insert the heat sink support bracket into the motherboard from the underside of the motherboard. The standoffs on the bracket are inserted into the holes in the motherboard. Refer to Figure 2 FIGURE 2 NOTE Make sure the top surfac ...

the motherboard. Refer to the main assembly guide for instructions on installing the I/O shield. Installing the Motherboard STANDOFF INSTALLATION Install two brass standoffs, included in the chassis integration kit, in the locations shown in the figure 1 below. HEATSINK INSTALLATION 1. Install the CPU following the instructions provided with the CPU. 2. Insert the heat sink support bracket into the motherboard from the underside of the motherboard. The standoffs on the bracket are inserted into the holes in the motherboard. Refer to Figure 2 FIGURE 2 NOTE Make sure the top surf ...

with the BOX motherboard. Refer to the main assembly guide for instructions on installing the I/O shield. Installing the Motherboard STANDOFF INSTALLATION Install two brass standoffs, included in the chassis integration kit, in the locations shown in the figure 1 below. HEATSINK INSTALLATION 1. Install the CPU following the instructions provided with the CPU. 2. Insert the heat sink support bracket into the motherboard from the underside of the motherboard. The standoffs on the bracket are inserted into the holes in the motherboard. Refer to Figure 2 NOTE Make sure the top surfa ...

shield supplied with the motherboard. Refer to the main assembly guide for instructions on installing the I/O shield. Installing the Motherboard STANDOFF INSTALLATION Install two brass standoffs, included in the chassis integration kit, in the locations shown in the figure 1 below. HEATSINK INSTALLATION 1. Install the CPU following the instructions provided with the CPU. 2. Insert the heat sink support bracket into the motherboard from the underside of the motherboard. The standoffs on the bracket are inserted into the holes in the motherboard. Refer to Figure 2 FIGURE 2 NOTE Make ...

supplied with the motherboard. Refer to the main assembly guide for instructions on installing the I/O shield. Installing the Motherboard STANDOFF INSTALLATION Install two brass standoffs, included in the chassis integration kit, in the locations shown in the figure 1 below. HEATSINK INSTALLATION 1. Install the CPU following the instructions provided with the CPU. 2. Insert the heat sink support bracket into the motherboard from the underside of the motherboard. The standoffs on the bracket are inserted into the holes in the motherboard. Refer to Figure 2 FIGURE 2 NOTE Make sure th ...