SKY-HERO Anakin Assembly Instruction Manual

GLUE THE TUBES END’S 1 ATTACH YOUR MOTORS 2 ATTACH MOTOR MOUNTS ON ARMS 3 ROUTE YOUR MOTOR CABLES 4 FIX YOUR SIDE FRAME USING 2 SCREWS 4 SOLDER YOUR ESC’S 4 USE SCHRINK TUBE TO PROTECT YOUR ESC’S 4 SLIDE ESC’S INTO THE TUBES 4 PRESS THE INSERT IN POSITION 4 CHOOSE THE POSITION OF YOUR ARMS 9 SLIDE YOUR MOTOR SHAFTS INTO THE MOUNTING JIG 10 SCREW YOUR LOWER FRAME 11 FIX YOUR MOTOR MOUNT 12 ATTACH YOUR Z SPACERS 13 FIX YOUR CAMERA PLATE IN POSITION 14 CAMERA ANGLE 15 ADJUST MOTORS ANGLE 16 ATTACH YOUR CANOPY 17 ...

ISO 7380 M3X6MM ISO 7380 M3X4MM ISO 7380 M3X6TP MM ISO 7380 M3X30MM ISO 7380 M2.5X8MM HEX NUT 2.5MM ...

(ou SKH03-240) SKH03-280 (REAR TUBE (ou SKH03-240 ) USE EPOXY GLUE USE EPOXY GLUE 8MM 8MM GLUE THE TUBES END’S Use 5min epoxy glue (Whipe out excess of glue with acetone) 1 Please make sure you push the tube to the maximum position of the tube’s end. * * * USE EPOXY GLUE FIG. 1 ...

ATTACH YOUR MOTORS Warning! Before starting: - Make sure to identify your clockwise (CW) and counter-clockwise (CCW) motors*. - Be aware that all your wires will go backwards as shown in figure 3 2 FIG. 2 FIG. 3 CW CW CCW CCW * Optional parts ...

BUILD 1CW+1CCW FOR REAR SIDE Pay attention to motor support orientation. (See figure) You must build 1CW+1CCW with the motors’s wires oriented to the side of the nut for Anakin’s front side And 1CW+1CCW with the motors’s wires oriented to the side of the screw for Anakin’s rear side FIG. 4 FIG. 5 ATTACH MOTOR MOUNTS ON ARMS You must attach the motor mounts until you ear a «clic» noise. (it can require quite an important pressure) ...

( LEFT SIDE ) SKH01-170-00 (OPTION = SKH06-001) ISO 7380 M3x8TP ROUTE YOUR MOTOR CABLES Rear cables = 220mm long / Front cables = 150mm long FIX YOUR SIDE FRAME USING 2 SCREWS Build left + right side 4 FIG. 6 FIG. 7 ...

it to check your motor rotation SOLDER YOUR ESC’S And check your motors direction Use schrink tube to protect your esc’s SKH04-014* 5 * Optional parts USE SOLDER & WELDING FIG. 8 FIG. 9 ...

In order to mount the frame you must first insert the PEM’s by tightening them one by one until you reach themaximum position. Use the threaded insert on upper frame. TIP: Use 1 frame spacer + 1 M3x30MM screw, to press your insert in position Once finished you will have this: 7 THREADED NOT THREADED SH54-03 FIG. 11 ...

(Use the threaded insert on upper frame) FRONT SPACER REAR SPACER SKH01-103-F SKH01-103-R SKH01-103-F SKH01-103-R Small center hole must always face up 8 FIG. 13 FIG. 12 ...

ACCORDING THE CENTER OF GRAVITY ADJUSTMENT YOU WANT FRONT SPACER REAR SPACER SKH01-103-F SKH01-103-R FRONT UP LOW CG CROSSED SETUP HIGH CG Standard setup REAR UP REAR UP REAR DOWN FRONT DOWN FRONT DOWN 9 FIG. 14 ...

TO YOUR BATTERY CONNECTOR CABLES SCREW YOUR LOWER FRAME (DO NOT OVERTIGHT) BATTERY CONNECTOR CABLES EQUIPEMENTS 11 FIG. 16 FIG. 17 ...

SKH01-109-00 SKH04-109-00 ATTACH YOUR Z SPACERS Fix your camera plate in position 14 FIG. 20 FIG. 21 FIG. 22 ...

20 ° 20 ° Standard setup 15 FIG. 23 FIG. 24 FIG. 25 * Optional parts * Cam * Cam * Cam ...

To adjust motor angle to banked position, you need to unscrew the plactic ring or alu ring on the side and tilt The motor mounts until the edge of the sideframes. WARNING! You need optional sideframes in order to do this. Check accessories in the Anakin section of our website (www.sky-hero.com) to order them or run to the closest Sky-Hero dealer! 0° 10° Standard setup Banked setup 16 FIG. 26 FIG. 27 ...