Xray XLL Link Instruction Manual

The XII is a high-quality, 1/12-pan car intended for persons aged 16 years and older with previous experience building and operating RC model racing cars. This is not a toy; it is a precision car model. This model racing car is not intended for use by beginners, inexperienced customers, or by children without direct supervision of a responsible, knowledgeable adult. If you do not fulfill these requirements, please return the kit in unused and unassembled form back to the shop where you have purchased it. Before building and operating your XII, YOU MUST read through all of the operating instructions and instruction manual and fully un ...

(#359235) Diff. Grease (HUDY #106211) SYMBOLS USED TOOLS REQUIRED TOOLS REQUIRED EQUIPMENT INCLUDED EQUIPMENT REQUIRED L=R 2x CA OIL Part bags used Assemble left and right sides the same way Assemble in the specified order Pay attention here Assemble as many times as specified (here twice) Apply CA glue Apply oil 05 Apply grease Ensure smooth non-binding movement Follow Set-up Book Side Cutters (HUDY #189010) Hobby Knife File Turnbuckle 4mm (HUDY #181040) Turnbuckle 3mm (HUDY #181030) Reamer (HUDY #107600) Pliers (HUDY #189020) Allen Wrench 1.5mm (HUDY #111540) Allen Wrench 2.0mm (HUDY #112040) Allen Wrench 2.5mm (HUD ...

CORRECT INCORRECT Lightly file edges of battery slots to remove sharp edges. Do not file battery slots too much, or batteries may protrude below the chassis bottom. To protect and seal edges of graphite parts, sand edges smooth and then apply CA glue. Fine sandpaper Use fine sandpaper to sand smooth the edges of all graphite parts. CA PREPARE All GRAPhitE PARtS Apply CA glue to all adges of the graphite parts. ...

FRONt COil SPRiNGS #372180 C=3.5 - GOLD (standard) #372181 C=4.0 - SILVER (option) #372182 C=5.0 - BLACK (option) #372183 C=6.0 - GREY (option) 372180 372020 372620 371102 372315 902312 901304 960031 372290 960031 377220 372315 372120 372291 373240 BAG 903312 902308 965019 372085 372290 372280 372130 373240 965019 372130 372650 964032 372220 375220 371102 XII LINK CHASSIS - 2.5MM GRAPHITE 372010 COMPOSITE FRONT UPPER ARM MOUNT - RIGHT 372020 COMPOSITE FRONT UPPER ARM MOUNT - LEFT 372085 FRONT BRACE - GRAPHITE 2.0MM 372110 COMPOSITE SUSPENSION ARM - FRONT LOWER - RIGHT 372120 COMPOSITE SUSPENSION ARM - FRONT LOWER - LEFT 372130 CO ...

NOTE ORIENTATION 2x 2x 2x REACtivE CAStER SEttiNG = 2.5° = 5° INITIAL SETTING = 7.5° Use same bushings in left and right sides. CASTER CAMBER 902308 SH M3x8 901304 SB M3x4 902312 SH M3x12 ...

VERY IMPORTANT 1. Mount the assembled left and right suspension to chassis by installing the bottom mounting screws in the order shown. Tighten the mounting screws VERY GENTLY, and do not overtighten the screws. 2. Fully tighten the screws in exactly the same order as you installed them. The front suspension is manufactured from composite material which may slightly move or bend when the mounting screws are tightened. As such it is extremely important to follow these steps to ensure tweak-free mounting. Marked “R“ Marked “L“ ASSEMBLED VIEW NOTE ORIENTATION NOTE ORIENTATION The nu ...

#372085 GRAPHITE BRACE (standard) 2mm Loosen all M3x4 setscrews so you can easily remove the pins. Make sure that arm moves freely. INITIAL SETTING After inserting clips, carefully tighten all M3x4 setscrews so the pins will not move. Do not overtighten or you may strip the plastic. If the arm does not have enough play, remove the clips and thin the clips slightly with sandpaper. The arms must have free movement and not bind. 1mm 0.5mm 2x FRONT BRACE CASTER ...

902258 371190 903314 902306 371190 373010 960031 373090 373065 903310 901308 373590 373581 960031 303241 903306 372650 303123 373030 903310 373541 902306 902308 372650 901308 903306 302654 373081 303120 373590 373581 903310 371142 373020 373072 903306 960031 902306 373090 903310 902258 303241 903306 303120 372651 903306 376350 373590 376360 376300 903308 903306 BAG 302654 BALL END 4.9MM WITH THREAD 8MM (2) 303120 SET OF ALU SHIM (0.5MM, 1.5MM, 2.5MM) 303123 ALU SHIM 3x6x2.0MM (10) 371142 LINK GRAPHITE 2.5MM REAR POD LOWER PLATE 371190 COMPOSITE POD LINK (2) 303241 BALL UNIVERSAL 5.8 MM HEX (4) 372650 BALL-END 4.2MM THREADED HUDY SP ...

Ensure free, smooth movement without excessive freeplay. Lightly tighten the screws so there is no free play, but do not overtighten otherwise the ball will not move freely. 903306 SFH M3x6 903310 SFH M3x10 902306 SH M3x6 960031 ALU N M3 903310 SFH M3x10 ...

BALLS MUST TURN FREELY. TIGHTEN FULLY 902258 SH M2.5x8 960031 ALU N M3 903306 SFH M3x6 903314 SFH M3x14 ...

960031 ALU N M3 ...

BAG 372070 COMPOSITE RIDE HEIGHT ADJUSTER SET (2) 375010 REAR AXLE SHAFT - GRAPHITE 375030 ALU REAR WHEEL HUB - RIGHT 375040 ALU REAR WHEEL HUB - LEFT 375050 ALU DIFF HUB 375080 D-LOCK DIFF PLATE (2) 375090 SET OF ALU SHIMS (0.5MM, 1.0MM, 2.0MM) 375896 COMPOSITE SPUR GEAR - 96T / 64P 908258 HEX SCREW SOCKET HEAD CAP M2.5x8 (10) 930130 CARBIDE BALL 3.175MM (12) 930138 CARBIDE BALL-BEARING AXIAL F3-8 3x8x3.5 941438 HIGH-SPEED BALL-BEARING 1/4“x3/8“x1/8“ RUBBER SEALED (2) 951438 BALL-BEARING ...

sideplay. If there is no side play, the axle may bind in the ball-bearings and damage the bearings. Use these Ride Height Adjusters for initial assembly. Use additional shims to widen the rear track-width. Use the same shims on both sides. For initial assembly use 6.4x8.4x1mm shims. Bearing Oil (HUDY #106230) Bearing Oil (HUDY #106230) OIL OIL Flanged Flanged RIDE HEIGHT TRACK WIDTH 951438 BB 1/4“x3/8“x1/8“ 375090 6.4x8.4x1.0 908258 SCH M2.5x8 ...

rear differential. Tighten the nut gently so the diff does not slip under power, but do not overtighten or damage to the diff balls and plates may occur. OIL Bearing Oil (HUDY #106230) OIL Diff Grease (HUDY #106211) Diff Grease (HUDY #106211) 8.0mm 7.8mm 3.0mm 3.2mm DIFERENTIAL 930138 BA 3x8 941438 BB 1/4“x3/8“x1/8“ 930130 B 3.1 963030 ST 3x8 960031 ALU N M3 ...