Arcam A49 Handbook & Instructions

Text of Arcam A49 Handbook & Instructions

Arcam A49 POWER / STANDBY

PHONO PHONO AUX CD TUNER SAT MUTE DISPLAY BALANCE BD PVR AV PHONES POWER POWER / STANDBY SP1 SP2 POWER POWER / STANDBY HANDBOOK Integrated amplifier/Pre-amplifier/Power amplifier A49/C49/P49/P349

CAUTION: To reduce the risk of electric shock, do not remove cover (or back). No user serviceable parts inside. Refer servicing to qualified

service personnel. WARNING: To reduce the risk of fire or electric shock, do not expose this apparatus to rain or moisture. The lightning flash with an arrowhead symbol within an equilateral triangle, is intended to alert the user to the presence of uninsulated ‘dangerous voltage’

Arcam A49 Placing the unit

< Place the amplifier on a level, firm surface, avoiding direct sunlight and sources of heat or damp. < Do not place the A49/C49/P49/P349 on top of a power amplifier or other source of heat. < Do not place the amplifier in an enclosed space such as a bookcase or closed cabinet unless there is good provision for ventilation. The A49/P49/P349 are designed to run warm during normal operation. < Do not place any other

Please read the ‘Placing the unit’, ‘Power’ and

‘Interconnect cables’ sections on page 5 before connecting up your A49 integrated amplifier! PHONO GROUND ONLY PHONO (MM) CD TUNER SAT BD PVR AV RECORD OUT PRE OUT R 4–16 OHMS. CLASS 2 WIRING SPEAKER 1 SPEAKER 2 L 4–16 OHMS. CLASS 2 WIRING SPEAKER 2 SPEAKER 1 AUX R AUX L PRE OUT R PRE OUT L TRIGGER OUT 6V 1A12V 1.5A ACCESSORY POWER 110-120V/220-240
Please read the ‘Placing the unit’, ‘Power’ and ‘Interconnect cables’ sections on page 5 before connecting up your P49 power amplifier! ST/BRIDGE/DM MODE XLR/RCA INPUT 25dB/31dB GAIN L R PRE IN PRE OUT R 4–16 OHMS. CLASS 2 WIRING SPEAKER 1 SPEAKER 2 L 4–16 OHMS. CLASS 2 WIRING SPEAKER 2 SPEAKER 1 PRE IN R PRE IN L 110-120V/220-240V ~ 50-60 Hz 350W MAX POWER INLET SUPPLY VOLTAGE SWITCH POSITIONS 115 = 11

The POWER button switches the unit on and off.

The power light (next to the ‘POWER / STANDBY’ text) indicates the state of the amplifier: it changes from red to orange then green if mains power is connected and the unit is switched on. If the unit is left unused for an extended period of time it will go into standby to reduce power consumption. Press AUX and BALANCE to adjust the time of this feature. Display The DISPLAY

SP1 and SP2

These buttons allow you to switch the speakers on and off. The LED above each button glows green to indicate which speakers are currently selected. If you are using the bi-wiring configuration described on page 15, both SP1 and SP2 must be switched on. Note that when both lights are out, the amplifier will appear not to work, as all speakers are switched off. SP1 SP2 POWER POWER / STANDBY Switching on The POWER button switche

AMP Device Mode

The A Device Mode button configures the CR902 to control your Arcam amplifier. Pressing this button does not affect the currently selected input on the amplifier. P Toggles power between standby and on DISP Cycles through the front panel display’s brightness options MENU Displays the amplifier setup menu on the front panel Navigate menus O confirms a selection @ Toggles the mute function of the amplifier VOL- VOL+ Decrea

Bi-amping requires the use of two amplifiers per

channel. Normally, your A49 is used to drive the high- frequency (treble) speakers, while a power-amplifier (such as a P49/P349) is used for the lower (bass) frequencies. Connect your A49 to the speakers as described for single wiring, with the exception that the A49 should be connected to the speaker terminals labelled HF or ‘High Frequency’. Then connect the power amplifier

4–16 OHMS. CLASS 2 WIRING

SPEAKER 1 SPEAKER 2 L 4–16 OHMS. CLASS 2 WIRING SPEAKER 2 SPEAKER 1 PRE IN R PRE IN L 110-120V/220-240V ~ 50-60 Hz 350W MAX POWER INLET SUPPLY VOLTAGE SWITCH POSITIONS 115 = 110 - 120V~ 230 = 220 - 240V~ TRIGGER IN TRIGGER OUT LF HF PHONO GROUND ONLY PHONO (MM) CD TUNER SAT BD PVR AV RECORD OUT PRE OUT AUX R AUX L PRE OUT R PRE OUT L TRIGGER

Continuous power output (20Hz—20kHz at 0.2% THD), per channel

Both channels, 8Ω, 20Hz—20kHz 200W Single channel, 4Ω, at 1kHz 400W Harmonic distortion, 80% power, 8Ω at 1kHz 0.001% Inputs Phono (MM) cartridge: Input sensitivity at 1kHz 5mV Input impedance 47kΩ + 100pF Frequency response (ref. RIAA curve) 20Hz—20kHz ± 1dB Signal/noise ratio (Awtd) 50W, ref. 5mV input 80dB Overload margin, 5mV at 1kHz 20dB Inputs: RCA type XLR typ
Continuous power output (20Hz—20kHz at 0.2% THD), per channel Both channels, 8Ω, 20Hz—20kHz 200W Single channel, 4Ω, at 1kHz 400W Harmonic distortion, 80% power, 8Ω at 1kHz 0.001% Inputs PWR IN input: RCA type XLR type Nominal sensitivity for 200W / 8Ω 1.15V 2.3V Input impedance 10kΩ 10kΩ Frequency response 20Hz—20kHz ± 0.05dB Signal/noise ratio (Awtd) ref 50W / 8Ω 110dB General Mains voltage 110–120V~ or 220–240V~ Power

Correct disposal of this product

This marking indicates that this product should not be disposed with other household waste throughout the EU. To prevent possible harm to the environment or human health from uncontrolled waste disposal and to conserve material resources, this product should be recycled responsibly. To dispose of your product, please use your local return and collection systems or contact the retailer where the produc

Arcam Amplifier Owners Instructions: