Beta Three T-2000 Manual 

Text of Beta Three T-2000 Manual 

1. POWER ON

ON/OFF switch with indication LED. 2.LEVEL Control of the input level of the external signal: operates with continual values which vary from" fully closed"(position" "-the signal is not fed to the amplifier sections) to "fully open"(position" 0dB")-the signal is sent to the amplifier sections at the same level as that with which it arrives ...

FRONT &REAR PANEL

Beta Three T-2000 1. POWER ON 2. LEVEL 3. BRIDGE 4. PROTEC 5. CLIP 6. SIGNAL 7. AIR VENTS 8. OUTPUTS 9. GROUND ON/FLOATING 10. INPUTS 2 3 4 5 6 6 6 6 6 6 6 6 6 6 HIGH PERFORMANCE POWER AMPLIFIERS 1 ...

1. MAINS POWER CONNECTION.

Beta Three T-2000 Before connecting the amplifier to the mains power socket, make certain that the voltage corresponds with that indicated on the rear of the unit (an allowance of 10% is acceptable). Before connecting the power cable to the mains, always make certain that is not damaged and that there are no bare wires, always connec ...

C L I P

Beta Three T-2000 SIGNAL 6 FRONT PANEL REAR PANEL HIGH PERFORMANCE POWER AMPLIFIERS 5 T-3000 PROFESSIONAL DESIGN R Beta Three CHA INPUT CHA OUTPUT CHB INPUT CHB OUTPUT CONNECTOR SAMPLER INPUT MODE MONO BRIDGE STEREO ON OFF LIFT GROUND LIMITER BRIDGE OUTPUT AC INPUT 220V/50HZ ! SPEAKON CONNECTOR NOTICE: ! ! ! CHA OUT CHB OUT BRI ...

Phase Response: +/-5 degree from 20Hz-50KHz.

Beta Three T-2000 Signal to noise ratio: 105dB(A-weighted)at full output and 28 dB GAIN. Total harmonic distortion(THD): ...

CAUTION!Do notlocate sensitive high-gain equip-

Beta Three T-2000 ment such as preamplifiers or tape decks directly above or below the unit . because this amplifier has a high power density . it has a string magnetic field which can induce hum into unshielded devices that are located nearby . The field is strongest just above and below the unit. If an eq ...

FRONT &REAR PANEL

1. POWER ON 2. LEVEL 3. BRIDGE 4. PROTEC 5. CLIP 6. SIGNAL 7. AIR VENTS 8. OUTPUTS 9. GROUND ON/FLOATING 10. INPUTS 2 3 4 5 6 6 6 6 6 6 6 6 6 6 HIGH PERFORMANCE POWER AMPLIFIERS 1

CAUTION!Do notlocate sensitive high-gain equip-

ment such as preamplifiers or tape decks directly above or below the unit . because this amplifier has a high power density . it has a string magnetic field which can induce hum into unshielded devices that are located nearby . The field is strongest just above and below the unit. If an equipmentrack is used , we recommend locating the amplifier ( s ) in the bottom of the rack and

Phase Response: +/-5 degree from 20Hz-50KHz.

Signal to noise ratio: 105dB(A-weighted)at full output and 28 dB GAIN. Total harmonic distortion(THD): <0.03% from 20Hz-50KHz to 1KHz increasing linearly to 0.1% at 50KHz. Intermodulation distortion(IMD)

1. MAINS POWER CONNECTION.

Before connecting the amplifier to the mains power socket, make certain that the voltage corresponds with that indicated on the rear of the unit (an allowance of 10% is acceptable). Before connecting the power cable to the mains, always make certain that is not damaged and that there are no bare wires, always connect the power cable to the amplifier before switching it on and only remove the cable after switching

C L I P

SIGNAL 6 FRONT PANEL REAR PANEL HIGH PERFORMANCE POWER AMPLIFIERS 5 T-3000 PROFESSIONAL DESIGN R Beta Three CHA INPUT CHA OUTPUT CHB INPUT CHB OUTPUT CONNECTOR SAMPLER INPUT MODE MONO BRIDGE STEREO ON OFF LIFT GROUND LIMITER BRIDGE OUTPUT AC INPUT 220V/50HZ ! SPEAKON CONNECTOR NOTICE: ! ! ! CHA OUT CHB OUT BRIDGE OUT +1=CHA+ +1=CHB+ +1=CHA+ -1=CHA- -1=CHB- -1=CHB- ! CAUTION RISK OF ELECTRIC SHOCK DO NOT OPE

1. POWER ON

ON/OFF switch with indication LED. 2.LEVEL Control of the input level of the external signal: operates with continual values which vary from" fully closed"(position" "-the signal is not fed to the amplifier sections) to "fully open"(position" 0dB")-the signal is sent to the amplifier sections at the same level as that with which it arrives at the input). 3. BRIDGE This LED will be light up when you choose "BRIDGE" mode on the back panel

Beta Three Amplifier Owners Instructions: