FOR-A USF-105DADA Operation Manual

Text of FOR-A USF-105DADA Operation Manual

FOR-A USF-105DADA Important Safety Warnings

[Operation] Stop Do not place the unit in the place of high temperature and high humidity, dusty, or high vibrations. Operation other than the operating environment conditions may cause malfunction, fire, or electrical shock. [Transportation] Caution Handle with care to avoid impact shock during transit, which may cause malfunction. When you need to transport the unit, use the original or suitable alternative packing

USF-105DADA modules and their accessories are fully inspected and adjusted prior to shipment. Check

your received items against the packing lists below. Check to ensure no damage has occurred during shipment. If damage has occurred, or items are missing, inform your supplier immediately.  USF-105DADA Box ITEM QTY REMARKS USF-105DADA 1 each USF-105DADA Front module USF-105DADA Rear module CD-ROM 1 Operation Manual (PDF) Screws 4 Rear modul

Table of Contents

1. 1. Prior to Starting ................................................................................................................................. 5 1-1. Overview ..................................................................................................................................... 5 1-2. Features ........................................................................................................................

1. 1. Prior to Starting

1-1. Overview The USF-105DADA is a digital audio distribution amplifier that can be installed in a USF frame. The USF-105DADA supports AES/EBU signals and is capable of producing up to 5 outputs from 1 input. LTS and Word Clock signals can be supported by changing the signal mode. Distribution numbers can be extended using multiple USF-105DADAs. 1-2. Features  Installs into USF frames  1 input 5 distribution outputs  Supp

2. Panel Descriptions

2-1. Front Panel USF-105DADA No. Name Description (1) POWER LED Lights green when normal DC power is supplied by USF frame. (2) INPUT LED *1 Lights when input signal is detected. (3) TERM LED On Input signal impedance is set to 75Ω. Off Input signal impedance is set to 1kΩ. (4) MODE LED On LEDs to confirm signal mode. One of the LED from AES, LTC, or WC is lit to indicate current signal mode. Flash or Off When LEDs are flashing or

2-2. Rear Panel

DIGITAL AUDIO IN USF-105DADA 1 2 3 4 5 DIGITAL AUDIO OUT Name Description DIGITAL AUDIO IN Input port. Signals compliant with the selected signal mode are input. DIGITAL AUDIO OUT 1 - 5 Output port. Distributes 5 outputs from signals that are input in DIGITAL AUDIO IN. IMPORTANT Maximum 7.5Vp-p signal is output from a DIGITAL AUDIO OUT port. Check that the signal mode is set correctly and the output signal level meets the equivalent level

FOR-A USF-105DADA 3. Switch Settings

 Switch Locations 3-1. S1: Reboot Power Reboot switch. Pressing the switch for 1 second starts rebooting the unit. 3-2. DS1 Switches 1 and 2: Signal Mode Settings Operation Mode Switch 1Setting Switch 2 Setting AES (Default) OFF OFF LTC ON OFF Word Clock OFF ON Do not change Switch 3 to 8 settings. Leave them OFF. 3-3. DS2 Switches 1 and 2: Signal Mode Settings Signal Mode Switch 1 Setting Switch 2 Setting AES (Default) OFF OFF L

Internal Bus Signal 1 to 3 varies according to the slot number in which the USF-105DADA is

installed. See the table below for details. Installed Slot No. Internal Bus Signal 1 Internal Bus Signal 2 Internal Bus Signal 3 1 Output from Slot 2 Output from Slot 3 Output from Slot 4 2 Output from Slot 1 Output from Slot 3 Output from Slot 4 3 Output from Slot 4 Output from Slot 2 Output from Slot 1 4 Output from Slot 3 Output from Slot 2 Output from Slot 1 5

3-6. Switch S2: MODE Set

Sets distribution mode settings. Setting Distribution Mode Settings AES distribution mode (Default) Set the switch toward AES. LTC distribution mode / Word Clock distribution mode Set the switch toward LTC/WC. 3-7. Switch S3: TERM Set Sets input signal impedance. Adjusts with input signal impedance in USF-105DADA. Setting Input Signal Impedance and Distribution Mode Settings Set impedance to 75Ω (default) in AES distribution m

FOR-A USF-105DADA 4. Signal Mode Settings

Three signal modes are available using USF-105DADA. AES Distribution Mode Inputs and distributes digital audio signals. Inputs AES/EBU signals with sample frequencies from 32 to 96KHz. * Gain is not adjustable using the front panel. LTC Distribution Mode Inputs and distributes LTC signals. Inputs LTC signal as signal input. Gain is adjustable using the front panel. (Adjustable gain range: Approx. ±3.0dB) Word Clock Distribution

LTC Distribution Mode Setting

DS1 Switch 1 ON DS1 Switch 2 OFF DS2 Switch 1 ON DS2 Switch 2 OFF S2 Switch Set the switch toward LTC/WC. S3 Switch Set impedance to 1kΩ. Word Clock Distribution Mode Setting DS1 Switch 1 OFF DS1 Switch 2 ON DS2 Switch 1 OFF DS2 Switch 2 ON S2 Switch Set the switch toward LTC/WC. S3 Switch Set impedance to 1kΩ. 4-1. When Signal Mode Is Correctly Set MODE LED on the front panel lights when power is turned on after installi

4-2. When Signal Mode Is NOT Set correctly

MODE LED on the front panel flashes or turned off when power is turned on after installing a USF-105DADA into a USF frame. When a USF-105DADA is installed in a USF-212S, Board Settings in Web GUI are indicated as Incorrect (Check FRONT CARD. S2, S3, DS1 and DS2 settings.). See Sec. 7 “Web GUI” for details. The output port is fixed to 0V. See Sec. 2-2 “Rear Panel” for details on output port details. 5. O

7. Web GUI Setup

Web GUI can be displayed when a USF-105DADA is installed into a USF-212S frame, but is not displayed when it is installed into a USF-212 frame. See USF-212S operation manual for details on displaying a Web GUI. Launch Web GUI and click USF-105DADA from slot no.1 to 12 of the USF-212S. The screen below opens.  Module Information Item Description Slot Installed slot number of USF-212S S/N USF-105DADA serial number MAC Address USF-105DA

Correct: Signal mode is correctly set.

Incorrect (Check FRONT CARD. S2, S3, DS1 and DS2 settings.): Signal mode is incorrectly set. See Sec.4 “Signal Mode Setting” and set the mode correctly. When signal mode is incorrectly set, signal is not output. Input Source Input Signal that gets distributed. Rear IN: Input signal via rear panel BNC “DIGITAL AUDIO IN” Slot1 - 12: Input signal via internal USF frame bus. Ou

8. SNMP (Simple Network Message Protocol) Function

The USF-105DADA can be remotely monitored using the SNMP (Simple Network Message Protocol) v2C protocol. An MIB (Management Information Base) file required in monitoring can be downloaded from Web GUI. See “Downloading MIB File” on the previous page. See the USF-212S Operation Manual for details on SNMP network settings.  GET List Category Object name Object name in MIB file Value OID Type Trap O

9. Extended Distribution Using Multiple USF-105DADAs

 Internal Bus Configuration Applying multiple USF-105DADAs enable you to increase the distribution number via a USF frame internal bus. Up to 4 USF-105DADAs can be applied and 20 distributed, from 1 input. Install USF-105DADAs in the internal bus slot that is the same as for the input signal. (Slot 1 to 4, Slot 5 to 8, or Slot 9 to 12) Set DS2, and Switch 3 to 7 to increase distribution number via

9-1. Settings to Distribute 10 Output Signals from 1 Input

When USF-105DADAs are installed into Slots 1 and 2 as shown below, settings to distribute 10 outputs from the Slot 1 input signal are explained in this section. (1) Set the signal mode of USF-105DADA in Slots 1 and 2 to the same mode. (Default: AES distribution mode) See Sec. 4 “Signal Mode Settings” for details. (2) Set DS2 of USF-105DADAs as shown in the table below. Slot 1 USF-105DADA - D

9-2. Settings to Distribute 15 Output Signals from 1 Input

When USF-105DADAs are installed in Slots 1, 2 and 3 as shown below, settings to distribute 15 outputs from the Slot 1 input signal are explained in this section. (1) Set signal mode of USF-105DADA in Slot1 - 3 as the same mode. (Default: AES distribution mode) See Sec. 4 “Signal Mode Setting” for details. (2) Set DS2 of USF-105DADAs as shown in the table below. Slot 1 USF-105DADA - DS2 setti

FOR-A USF-105DADA 9-3. Settings to Distribute 20 Output Signals from 1 Input

When USF-105DADAs are installed into Slot 1 to 4 as shown below, settings to distribute 20 outputs from the Slot 1 input signal are explained in this section. (1) Set signal mode of USF-105DADA in Slots 1 to 4 to the same mode. (Default: AES distribution mode) See Sec. 4 “Signal Mode Settings” for details. (2) Set DS2 of USF-105DADAs as shown in the table below. Slot 1 USF-105DADA - DS2 sett

FOR-A Amplifier Owners Instructions: