G&D DevCon-Center Installation Manual

Text of G&D DevCon-Center Installation Manual

i · G&D DevCon-Center

About this guide This guide is authored with special diligence and verified by the state of the art for correctness. G&D neither explicitly nor implicitly takes guarantee or responsibility for the qual- ity, efficiency and marketability of the product when used for a certain purpose that differs from the scope of service covered by this guide. For losses, which directly or indirectly result from the use of the documentation as well a

G&D DevCon-Center · ii

Contents Safety guidelines ............................................................................................... 1 The »DevCon-Center« appliance ...................................................................... 2 Scope of delivery ............................................................................................... 2 Installation ....................................................................

G&D DevCon-Center 1 · G&D DevCon-Center

Safety guidelines Please read the following safety guidelines attentively before you start running the G&D product. The guidelines help to avoid damage to the product and prevent pos- sible injuries. Inform all persons that use this equipment in detail about these safety guidelines. Observe all warnings or operating instructions put on the device or stated in this operating guide. , Avoid the risk of electric shock

G&D DevCon-Center The »DevCon-Center« appliance

G&D DevCon-Center · 2 The »DevCon-Center« appliance The Config Panel web application is integrated into various G&D devices. It provides the graphical user interface to configure and monitor the devices. Adding an DevCon-Center appliance to the existing G&D devices (with integrated web application) adds up to a KVM system which enables you to centrally configure and monitor the single devices. Scope of delivery  1 × D

G&D DevCon-Center 3 · G&D DevCon-Center

Installation Establishing a connection to up to two local networks Network A: Insert a category 5 twisted pair cable (or better). Network B: If you want to integrate the DevCon-Center appliance into another network, insert the category 5 (or better) cable into this interface. Connect the other end of the cable to the local network. Establishing the power supply Main Power: Insert the supplied PowerCable-2 Standard power

Initial configuration of the network settings

G&D DevCon-Center · 4 Initial configuration of the network settings In order to access the web application, the network settings of the DevCon-Center appliance on which the web application is operated are to be configured. The following table lists the default settings of the Network A network interface: How to configure the network settings before integrating the device into the local network: 1. Connect the
Initial configuration of the network settings 5 · G&D DevCon-Center 8. Use the paragraphs Interface A and/or Interface B to enter the following data: 9. Enter the following data in the section Global network settings: 10.Click OK to save your data. 11.Click the Logout symbol (see figure on the right) to end the active session of the web application. 12.Remove the twisted pair cable connection between computer and the appliance. 13.Integrate the appliance

Adjusting a common database for all devices

G&D DevCon-Center · 6 Adjusting a common database for all devices In order to being able to use the web application of the DevCon-Center appliance to administer, configure and monitor all devices of the KVM system, the databse set- tings of the different devices need to be configured. How to define a device’s database settings: 1. Open the Config Panel web application of the respective device and log in with y

Using the Reset button

7 · G&D DevCon-Center Using the Reset button The Reset button is located between the Identification LED and the RS 485 interface on the front panel of the computer module and the user module. This button enables you to reset the default settings as well as to temporarily deacti- vate the netfilter rules. Resetting the default settings Pressing and holding the button during booting resets the default setting of the DevCon-Center appl
Using the Reset button G&D DevCon-Center · 8 Temporarily deactivating the netfilter rules In the default status of the DevCon-Center appliance, all network computers have access to the extender’s IP address (open system access). The web application enables you to create netfilter rules to control the access to the appliance. As soon as a netfilter rule has been created, the open access to the system is deactivated and all incoming data packets are compa

9 · G&D DevCon-Center

Status displays Various status LEDs enable you to control the DevCon-Center’s current operating status. The following table lists all possible operating states and the respective LED displays: Range LED Status Meaning Ident. Ident. on Lights up as soon as the LED has been activated via the web application. Power Red. on The power pack is switched on and supplies the necessary voltage. off The power pack is switched

G&D DevCon-Center · 10

Technical data Interfaces Network: 2 × RJ45 socket RS232: 1 × RJ11 socket RS485: 1 × RJ45 socket Service: 1 × Mini-USB socket (Typ B) USB 2.0: 2 × USB-A socket Main power supply Type: internal power pack Connection: IEC plug(IEC-320 C14) Voltage: AC100-240V/60-50Hz Redundant  power supply Type: internal power pack Connection: IEC plug (IEC-320 C14) Voltage: AC100-240V/60-50Hz Current consumption  Operation

Guntermann & Drunck GmbH

Dortmunder Str. 4a 57234 Wilnsdorf Germany Phone +49 2739 8901-100 Fax +49 2739 8901-120 http://www.GDsys.de [email protected] A9200076

G&D LCD Drawer Owners Instructions: