Ampeg SVP-PRO Owner's Manual
Text of Ampeg SVP-PRO Owner's Manual
Owners Guide for the
Owners Guide for the
Bass Preamp
Bass Preamp
10k
4k
2k
1k
50
300
180
90
40
PEAK / MUTE
-15dB
MUTE
LO
BRT
HI
EQ
ACTIVE /
PEAK
ON
LEVEL
+8dB
-10dB
0
+12dB
-12dB
ULTRA LO /
BRIGHT
ULTRA HI /
GRAPHIC EQ
PAD /
MUTE
GAIN
DRIVE
BASS
MIDRANGE
FREQUENCY
TREBLE
GRAPHIC EQ
MASTER
POWER
INPUT
Ampeg® is Proudly Made in America
Ampeg® is Proudly Made in America
Important Safeguards and Precautions:
All Ampeg products are designed for continuous safe operation, as long as common sense is used and steps are taken to
help avoid certain problems. Abiding by the following rules can help prevent damage to your preamp, yourself and others.
• The preamp is equipped with a three-pronged AC power cord. To reduce the risk of electrical shock, NEVER
remove or otherwise attempt to defeat the ground pin of the power cord.
An Introduction to your new Ampeg SVP-PRO Bass Preamp
The harmonically rich sound and legendary performance of the AMPEG SVT are redefined in
the SVP-PRO. This dynamic preamp delivers unsurpassed quality, reliability and tonal flexibility
and offers the classic vibrancy of tubes. The SVP-PRO is the preamp section of our much-
respected SVT-2 PRO. All of the features and controls of your SVP-PRO are covered in detail in
this owner’s guide. We recommend
SVP-PRO Bass Preamp
The Front Panel Controls and Their Use
10k
4k
2k
1k
50
300
180
90
40
PEAK / MUTE
-15dB
MUTE
LO
BRT
HI
EQ
ACTIVE /
PEAK
ON
LEVEL
+8dB
-10dB
0
+12dB
-12dB
ULTRA LO /
BRIGHT
ULTRA HI /
GRAPHIC EQ
PAD /
MUTE
GAIN
DRIVE
BASS
MIDRANGE
FREQUENCY
TREBLE
GRAPHIC EQ
MASTER
POWER
INPUT
1
5
2 3
6 7
1314
4
8
9
10
11
12
18
20
19
16 17
15
1. INPUT: The signal output from an
instrument (active or passive) or a line
level signal may be connected
SVP-PRO Bass Preamp The Rear Panel
MADE IN THE U.S.A. BY
SLM ELECTRONICS
1400 FERGUSON AVENUE
ST. LOUIS, MO 63133
AC LINE IN
115V 230V
SVP PRO
2556A
MODEL #
SERIAL #
FOOT
SWITCH
PREAMP OUT
EFFECTS
TUNER
OUT
TRANSFORMER BAL. OUT
PRE
POST
RETURN
SEND
21
22
23
24
25
26
27
28
29
21. AC LINE IN: Firmly insert the sup-
plied AC power cord into this socket
until it is fully seated. Plug the male
end of the cord into a grounded AC
outlet.
DO
NOT
DEFEAT
THE
Ampeg SVP-PRO Some Suggested Settings*
SVP-PRO Bass Preamp
PEAK / MUTE
LO
BRT
HI
EQ
PEAK / MUTE
LO
BRT
HI
EQ
PEAK / MUTE
LO
BRT
HI
EQ
PEAK / MUTE
LO
BRT
HI
EQ
ULTRA LO /
BRIGHT
ULTRA HI /
GRAPHIC EQ
GAIN
DRIVE
BASS
MIDRANGE
FREQUENCY
TREBLE
ULTRA LO /
BRIGHT
ULTRA HI /
GRAPHIC EQ
GAIN
DRIVE
BASS
MIDRANGE
FREQUENCY
TREBLE
ULTRA LO /
BRIGHT
ULTRA HI /
GRAPHIC EQ
GAIN
DRIVE
BASS
MIDRANGE
FREQUENCY
TREBLE
ULTRA LO /
BRIGHT
ULTRA HI /
GRAPHIC EQ
GAIN
DRIVE
BASS
MID
SVP-PRO Bass Preamp Changing the Tubes
The performance characteristics of tubes are degraded in direct proportion to how often and under what conditions the
amplifier is used. Preamp tubes typically last longer than power tubes. When a preamp tube wears out, the preamp may
squeal, get noisy, lose gain and sensitivity, or just quit working. A service center can determine which tube(s) may need
replacing. To gain access to the tubes in the SVP-PRO, the top
Ampeg reserves the right to change specifications without notice.
Ampeg is proudly Made in America
©1999 SLM Electronics
1400 Ferguson Avenue
St. Louis, MO 63133 U.S.A.
P/N 47-546-13 • 05/99
Technical Specifications
TOTAL SYSTEM GAIN
76dB, @1kHz w/levels up, tones flat; -3dB @30Hz, 15kHz
TONE CONTROL RANGE
Bass:
±12dB @ 40Hz
Midrange:
+12dB, -15dB @ Frequency selected (220, 450, 800, 1.6k or 3kHz)
Treble:
±12dB @ 4kHz
Ultra Low:
+3dB @ 40Hz, -12dB @ 5