Icom IC-V8000 Optional Instructions

Text of Icom IC-V8000 Optional Instructions

VHF FM TRANSCEIVER

1 ANI FUNCTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1 ‘ General . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1 ‘ Preparation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2 ‘ Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3 ‘ Relative functions . . . . . . . . . . . . . . . . . . . . . . .

Icom IC-V8000 The ANI (Automatic Number Identification) function is a

method of selective calling which features an answer back function. This allows you to confirm whether or not a call has reached the receiving party, even if the operator is temporar- ily away from the transceiver. In order to use the IC-V8000’s ANI function, the following items and operation are necessary. • UT-108 DTMF DECODER UNIT • ANI code programming (via transceiver or PC, usin

q Push [BANK(OPT)] for 1 sec. to select the pager mode.

• Repeat several times if necessary. • 100 MHz digit shows “P.” w Program your ID and the station codes. • Set your ID into channel C0 and station codes into C1 to C6. ➥ Push [SET(LOCK)]. ➥ Rotate the tuning dial to select the code channel. ➥ Push [MW(S.MW)] then rotate the tuning dial to set the 1st digit of a code. Repeat this step 2 more times to inp

D Calling a specific station

q Turn the power ON. w Rotate the tuning dial to select the desired channel. • “A” is displayed beside the channel number on the ANI set channel. e Push [SET(LOCK)] then rotate the tuning dial to select the desired code channel C1 to C6, or set the 3-digit ANI code, if desired. • Push [TONE(T-SCAN)] to return to the previous conditions. r Push [PTT] to connect to the selected station. •

D Calling group stations

q Select the desired ANI set channel. w When using HM-118TN/TAN: Push [M] then enter the 3-digit group code. [A] or [D] must be included at least once. When using HM-133V: Push [M(TONE-1)] then enter the 3-digit group code. [CLR A(MW)] or [SQLY D(MUTE)] must be included at least once. • Transmits automatically after the 3rd digit code is entered. • When making group calls, the transceiver does not ring and no a

‘ Related functions

The following functions for the ANI operation are added to the initial set mode when the optional UT-108 DTMF DECODER UNIT is installed. Initial set mode programming q While pushing [(SET(LOCK)], turn the power ON. w Push [SET(LOCK)] or [MW(S.MW)] several times to select the desired item. e Rotate the tuning dial to set the condition or value. • Push [PWR] to exit the initial set mode. D Time-out timer To prevent ac

D Lock out function

Turns the busy channel lock out function ON and OFF. ANC--ON : Transmit is inhibited when the channel is busy. ANC--OF : Transmit is permitted even when the channel is busy.

D Hardware setup

The following hardware setup is required before installing the optional UT-109/UT-110 VOICE SCRAMBLER UNIT, as the scram- bler unit is installed into the microphone amplifier circuit (for transmission) and AF circuit (for reception). D Setup instructions q Turn the power OFF, then disconnect the power cable. w Remove the 3 allen-socket bolts from the front panel using with an allen wrench (2.5 mm; 1⁄1

Icom IC-V8000 D Scrambler setting

q Push [SET(LOCK)] to enter set mode. w Push [SET(LOCK)] or [MW(S.MW)] several times until “SCG” appears. • When the UT-109 is installed, skip steps w and e. Continue from step r. e Rotate the tuning dial to select the desired group code from 1–4. • The same group code must be selected in your group. r Push [SET(LOCK)] or [MW(S.MW)] several times until “SCR” appears. t Rotate the tuning dial to select t

Icom Transceiver Owners Instructions: