Immersion RC Vortex 230 Mojo Quick Start Manual

Text of the manual

Quick​ ​Start​ ​Guide

International​ ​edition Rev​ ​1.0​ ​-​ ​Oct​ ​2017 Every​ ​Vortex​ ​230​ ​Mojo​ ​is​ ​flight​ ​tested​ ​before leaving​ ​the​ ​factory. Flight​ ​Tested​ ​By:

Congratulations​ ​on​ ​your​ ​purchase​ ​of​ ​one​ ​of​ ​the​ ​world’s​ ​finest​ ​ARF​ ​pure-bred​ ​freestyle/racing​ ​mini-quads.​ ​A

product​ ​designed​ ​by​ ​FPV​ ​pilots,​ ​for​ ​FPV​ ​pilots. Do​ ​not​ ​expect​ ​it​ ​to​ ​fly​ ​li

4​ ​Steps:​ ​Unboxing​ ​to​ ​Racing

To​ ​get​ ​your​ ​ARF​ ​Vortex​ ​ready​ ​to​ ​race,​ ​follow​ ​the​ ​simple​ ​4-step​ ​process​ ​below. 1)​ ​Install​ ​Compatible​ ​R/C​ ​Receiver 2)Install​ ​suitable​ ​battery 3)​ ​Setup​ ​the​ ​video​ ​link 4)​

1)​ ​Install​ ​Compatible​ ​R/C​ ​Receiver

The​ ​Vortex​ ​230​ ​Mojo​ ​is​ ​shipped​ ​with​ ​three​ ​receiver​ ​interface​ ​cables,​ ​supporting​ ​4​ ​commonly​ ​used interfaces. a) 3-Pin​ ​0.1”​ ​Servo​ ​Cable,​ ​for​ ​S-Bus,​ ​and​ ​CPPM​ ​(5V) b) 5-pi

Finally,​ ​the​ ​receiver​ ​antennas​ ​may​ ​be​ ​routed​ ​through​ ​the​ ​two​ ​notches​ ​in​ ​the​ ​bottom​ ​of​ ​the​ ​LED​ ​diffuser,​ ​or

through​ ​the​ ​two​ ​notches​ ​in​ ​front​ ​of​ ​the​ ​two​ ​rear​ ​arms,​ ​which​ ​is​ ​the

C​ ​-​ ​Rating

Battery​ ​C’​ ​rating​ ​is​ ​a​ ​particularly​ ​inflated​ ​specification​ ​for​ ​mini-quad​ ​batteries,​ ​as​ ​a​ ​rule​ ​of​ ​thumb​ ​we’d suggest​ ​purchasing​ ​the​ ​highest​ ​C​ ​rated​ ​pack​ ​available. NOTE:​ ​Ensure​ ​that​

3)​ ​Setup​ ​the​ ​Video​ ​Link

To​ ​avoid​ ​the​ ​traditional​ ​fiddling​ ​with​ ​DIP​ ​switches​ ​to​ ​set​ ​up​ ​your​ ​video​ ​transmitter,​ ​the​ ​Vortex​ ​does​ ​not​ ​use a​ ​DIP​ ​switch​ ​to​ ​set​ ​up​ ​Vtx​ ​channels​ ​or​ ​b

4)​ ​Run​ ​the​ ​Tx​ ​Wizard

In​ ​the​ ​world​ ​of​ ​R/C,​ ​there​ ​is​ ​little​ ​standardization​ ​between​ ​equipment​ ​manufacturers​ ​as​ ​far​ ​as​ ​control​ ​stick to​ ​channel​ ​mapping.​ ​There​ ​is​ ​also​ ​little​ ​agreement​ ​between​

Other Quadcopters Manuals