Keysight E5071C Configuration Manual

– 9 kHz to 4.5/6.5/8.5 GHz – 100 kHz to 4.5/6.5/8.5 GHz (with bias tees) – 300 kHz to 14/20 GHz (with bias tees) E5092A Configurable Multiport Test Set Configuration Guide

1. Order the 82357B USB/GPIB interface at the same time if you want to control power meters with the E5071C. This will allow you to conduct scalar mixer calibrations (SMC), power calibrations, or receiver calibra- tions after power calibrations. 2. E5071C-TDR is a superset of E5071C-010. To add option TDR, you do not need to have option 010 already installed; however, you can have both option 010 and TDR installed in one instrument 3. Consider purchasing Keysight 20mm TORQUE WRENCH 8710-1764 for NMD 3.5 mm(f) test port connector. This configuration guide describes standard configurations, op- tions, accessories and peripherals for the E5071C ENA network analyzer. Refer to the ENA brochure for a complete description of the ENA network analyzer and the E5092A configurable multiport test set. E5071C ENA Network Analyzer The ENA is an integrated network analyzer with a two- or four- port S-parameter test set, a synthesized RF source, a 10.4-inch color LCD, and a hard disk drive. A 3-year return-to-Keysight Technologies, Inc. service warranty is included with the each ENA network analyzer. Step 1: Select frequency range, number of test ports, and with or without bias tees Up to 4.5 GHz range 9 kHz to 4.5 GHz (without bias tees) E5071C-240 2-port S-parameter test set E5071C-440 4-port S-parameter test set 100 kHz to 4.5 GHz (with bias tees) E5071C-245 2-port S-parameter test set E5071C-445 4-port S-parameter test set Up to 6.5 GHz range 9 kHz to 6.5 GHz (without bias tees) E5071C-260 2-port S-parameter test set E5071C-460 4-port S-parameter test set 100 kHz to 6.5 GHz (with bias tees) E5071C-265 2-port S-parameter test set E5071C-465 4-port S-parameter test set Up to 8.5 GHz range 9 kHz to 8.5 GHz (without bias tees) E5071C-280 2-port S-parameter test set E5071C-480 4-port S-parameter test set 100 kHz to 8.5 GHz (with bias tees) E5071C-285 2-port S-parameter test set E5071C-485 4-port S-parameter test set Up to 14 GHz range3 300 kHz to 14 GHz (with bias tees) E5071C-2D5 2-port S-parameter test set E5071C-4D5 4-port S-parameter test set Up to 20 GHz range3 300 kHz to 20 GHz (with bias tees) E5071C-2K5 2-port S-parameter test set E5071C-4K5 4-port S-parameter test set Step 2: Select time base E5071C-1E5 High stability time base E5071C-UNQ Standard stability time base Step 3: Select hard disk drive E5071C-017 Removable hard disk drive E5071C-019 Standard hard disk drive Step 4: Choose additional options (Optional) E5071C-0081 Frequency offset mode E5071C-TDR2 Enhanced time domain analysis E5071C-010 Time domain analysis E5071C-790 Measurement Wizard Assistant software Step 5: Choose accessories (Optional) E5071C-1CM Rack mount kit, E5071C-1CN Front handle kit E5071C-1CP Rack mount and front handle kit E5071C-810 Adds a keyboard E5071C-820 Adds a mouse Step 6: Choose certification documentation (Optional) E5071C-1A7 ISO 17025 compliant calibration E5071C-A6J ANSI Z540 compliant calibration Step 7: Choose your warranty service (Optional) 5 year return-to Keysight warranty and service Documentation The documentation for the E5071C is located in the Online Help system for the E5071C ENA network analyzer. The ENA Service Guide and Online Help system are also available on the Web site: www.keysight.com/find/ena Additional product information For additional product information, refer to the ENA brochure available on the Web site: www.keysight.com/find/ena

Receiver assignment Port 1 R1 A R2 B R3 C R4 D Port 2 Port 3 Port 4 Port 1 R1 A R2 B Port 2 2-port test set option 4-port test set option

E5071C ENA Network Analyzer Options To add options to a product, order the corresponding item number. Option1 Description Additional information Test set Option 240 Option 440 Option 245 Option 445 Option 260 Option 460 Option 265 Option 465 Option 280 Option 480 Option 285 Option 485 2-port test set, 9 kHz to 4.5 GHz without bias tees 4-port test set, 9 kHz to 4.5 GHz without bias tees 2-port test set, 100 kHz to 4.5 GHz with bias tees 4-port test set, 100 kHz to 4.5 GHz with bias tees 2-port test set, 9 kHz to 6.5 GHz without bias tees 4-port test set, 9 kHz to 6.5 GHz without bias tees 2-port test set, 100 kHz to 6.5 GHz with bias tees 4-port test set, 100 kHz to 6.5 GHz with bias tees 2-port test set, 9 kHz to 8.5 GHz without bias tees 4-port test set, 9 kHz to 8.5 GHz without bias tees 2-port test set, 100 kHz to 8.5 GHz with bias tees 4-port test set, 100 kHz to 8.5 GHz with bias tees Test port connector: Type-N (f) Option 2D5 Option 4D5 Option 2K5 Option 4K5 2-port test set, 300 kHz to 14 GHz with bias tees 4-port test set, 300 kHz to 14 GHz with bias tees 2-port test set, 300 kHz to 20 GHz with bias tees 4-port test set, 300 kHz to 20 GHz with bias tees Test port connector: 3.5 mm (m)5 Time base Option UNQ Option 1E5 Standard stability time base High stability time base Adds a higher stability time base reference. Hard disk drive Option 017 Option 019 Removable hard disk drive Standard hard disk drive Additional features Option 0082 Option TDR3 Option 010 Option 7904 Frequency offset mode Enhanced time domain analysis Time domain analysis Measurement wizard assistant software Adds frequency-offset sweep and harmonic measurement capabilities. Adds time domain transform, gating capabilities and graphical user interface to simplify time domain measurements. Adds time domain transform and gating capabilities. Adds Measurement Wizard Assistant (MWA) software to simplify your multiport measurements with the 4-port ENA Accessories Option 1CM Option 1CN Option 1CP Option 810 Option 820 Rack mount kit Front handle kit Rack mount and front handle kit Add keyboard Add mouse Adds a rack mount kit (part number: 1CM015A) for use without handles. Adds a front handle kit (part number: 1CN005A). Adds a rack mount and front handle kit (part number: 1CN009A). Calibration documentation Option 1A7 Option A6J ISO 17025 compliant calibration ANSI Z540 compliant calibration 1. Options are ordered using the combined model/option number, e.g. E5071C-240. 2. Order the 82357B USB/GPIB interface at the same time if you want to control power meters with the E5071C. This will allow you to conduct scalar mixer calibrations (SMC), power calibrations, or receiver calibrations after power calibrations. 3. Option TDR is a superset of Option 010. Option TDR and Option 010 are mutually exclusive options and there is no need to purchase both options. 4. When using an ECal module with the MWA calibration wizard, a 4-port ECal module (i.e. N4431B, N4433A) is required. 5. Consider purchasing Keysight 20mm TORQUE WRENCH 8710-1764

SW6 6A 6B 6COM SW7 7A 7B 7COM SW8 8A 8B 8COM SW9 9A 9B 9COM SW10 10A10B 10COM SW5 5A 5COM 5B SW1 1A 1B 1C 1D PORT 1 SW2 2A 2B 2C 2D PORT 2 SW3 3A 3B 3C 3D PORT 3 SW4 4A 4B 4C 4D PORT 4 1. Semi-rigid cables are designed for connection to the E5071C and are not available for the E5070B, E5071B. E5092A Configurable Multiport Test Set This guide is intended to assist you in the ordering process of the E5092A configurable multiport test set for use with the 4-port ENA (E5070B, E5071B and E5071C). Multiple multiport measure- ment configurations, from 50 MHz to 20 GHz, can be made by connecting included semi-rigid cables to the E5092A's front panel which accesses its internal switches. Step 1:1 Select appropriate cable and adapter set for connection to the ENA (Optional) E5092A-08C Cables and adapters for connection to E5071C Option 440/445/460/465/480/485 E5092A-20C Cables and adapters for connection to E5071C Option 4D5/4K5 Step 2: Choose accessories (Optional) E5092A-1CM Rack mount kit only E5092A-1CN Front handle kit only E5092A-1CP Rack mount kit with handle kit Step 3: Choose calibration certification documentation (Optional) E5092A-1A7 ISO 17025 compliant calibration E5092A-A6J ANSI Z540 compliant calibration Step 4: Choose your warranty service (Optional) 3 year return-to-Keysight warranty and service 5 year return-to-Keysight warranty and service Block diagram E5092A (Option 020) Documentation The documentation for the E5092A is located in the Online Help system for the E5071C ENA network analyzer. The ENA Service Guide and Online Help system are also available on the Web site: www.keysight.com/find/ena Additional product information For additional product information, refer to the ENA brochure available on the Web site: www.keysight.com/find/ena www.keysight.com/find/multiport

E5092A Configurable Multiport Test Set Options To add options to a product, order the corresponding option number. Option1 Description Additional information Test set Option 020 20 GHz switching test set Up to 22-port or 10-port full crossbar measurement. Cable adapter set Option 08C Cable and adapter set for E5071C Option 440/445/460/465/480/485 (4.5 GHz/6.5 GHz/8.5 GHz) Adds SMA semi-rigid cables and type-N-to-SMA adapters for connection to the E5071C. Option 20C Cable and adapter set for the E5071C Option 4D5/4K5 (14 GHz/20 GHz) Adds SMA semi-rigid cables and 3.5 mm-to-3.5 mm adapters for connection to the E5071C. Accessories Option 1CM Rack mount kit Adds a rack mount kit (part number: 1CM015A) for use without handles. Option 1CN Front handle kit Adds a front handle kit (part number: 1CN007A). Option 1CP Rack mount and front handle kit Adds a rack mount and front handle kit (part number: 1CP008A). Calibration documentation Option 1A7 ISO 17025 compliant calibration Option A6J ANSI Z540 compliant calibration 1. Options are ordered using the combined model/option number, e.g. E5092A-020.

Option 1E5 High stability time base Option 1E5 provides the following stability: CW accuracy: ±1 ppm (specification) Source stability: ±0.05 ppm (5 °C to 40 °C typical), ± 0.5 ppm/year Hard disk drive options2 Option 019 Standard hard disk drive Option 019 provides a fixed hard disk drive. The removable disk drive is not available. Option 017 Removable hard disk drive Option 017 provides a removable hard disk drive. You can remove or replace the hard disk drive for secure area operations. If a spare disk is needed, order E5071CU-058 Solid state drive kit. Certification options Option 1A7 ISO 17025 compliant calibration Option 1A7 provides a complete set of measurements which test the unit to manufacturer’s published specifications. Includes cali- bration label, ISO 17025 calibration certificate, and data report, and measurement uncertainties and guardbands on all customer specifications. Conforms to ISO 17025 and ISO 9001. Option A6J ANSI Z540 compliant calibration Option A6J provides a complete set of measurements which test the unit to manufacturer’s published specifications. Includes pre- and post-adjustment data and measurement uncertainty information compliant with the ANSI/NCSL Z540 standard. 1. When using an ECal module with MWA calibration wizard, a 4-port ECal module (i.e. N4431B, N4433A) is required. 2. A solid state drive is used as storage from Sep 2012. ENA Network Analyzer (E5071C) Additional software options Option TDR Enhanced time domain analysis Option TDR enables the ENA to view reflection and transmission responses in the time domain using a simple and intuitive graphi- cal user interface. Use time domain to tune filters, gate out the response of fixtures and cables, characterize the impedance of transmission lines, and more. Option 010 Time domain analysis Option 010 enables the ENA to view reflection and transmission responses in the time domain. Use time domain to tune filters, gate out the response of fixtures and cables, characterize the impedance of transmission lines, and more. Option 008 Frequency offset mode Option 008 enables the ENA to set the receiver frequencies independently from where the source frequency is tuned. This ability is important for harmonic distortion measurements and for measuring frequency converting devices such as mixers and converters. Advanced calibration techniques for the ENA, such as scalar mixer calibration (SMC) or vector mixer calibration (VMC), require this option. Option 790 Measurement Wizard Assistant Option 790 provides a simple measurement procedure setup for the 4-port ENA with a multiport test set such as the E5092A. The software delivers an easy-to-use measurement wizard programs including a calibration wizard setup1, which reduces operation time for complicated, time-consuming multiport measurements. Time base options Option UNQ Standard stability time base Option UNQ provides following stability: CW accuracy: ±5 ppm (specification) Source stability: ±5 ppm (5 °C to 40 °C typical)

1. A sliding load is not supported by the ENA. 2. An offset load is not supported by the ENA. Measurement Accessories A complete list of RF and microwave test accessories is available on our Web site: www.keysight.com/find/accessories Accessories are available with the following connector types: 50 Ω Type-N, 3.5 mm, 7 mm, 2.4 mm, 2.92 mm, 1.85 mm, 1.0 mm and waveguide. Test port cables and a calibration kit/ECal module should be added for a complete measurement system. Calibration kits Coaxial measurements Mechanical calibration kits include standards, such as opens, shorts and loads, which are measured by the network analyzer for increased measurement accuracy. Electronic calibration (ECal) kits replace mechanical calibration standards with one solid-state calibration module that is con- trolled by the network analyzer via USB. ECal kits provide many different impedances to the test ports which enables a full two- port calibration to be performed quickly with a single connection. This technique reduces operator errors and connector wear and abrasion. Choose a calibration kit for each connector type to be used. Economy, includes: – open standards (male and female) – short standards (male and female) – fixed-termination standards (male and female) Standard, includes the devices in the economy kit and adds: – sliding load standards1 (male and female) or a series of offset shorts Precision, includes the devices in the economy kit and adds: – 50 Ω airline(s) for TRL calibration – TRL adapters Waveguide measurements For waveguide measurements, Keysight offers mechanical cali- bration kits that include: – waveguide-to-coax adapters (X, P, K, R, Q, U, and V bands) – precision waveguide section – flush short circuit – fixed terminations2 – straight section Cables and adapter sets Keysight offers the following types of cables: – single cables: semi-rigid or flexible – cable sets: semi-rigid or flexible There are also adapter sets that protect the test port and convert the port to the desired connector interface. These kits contain: – one male adapter – one female adapter To attain the best mechanical rigidity for device connection, use a single cable and the appropriate special adapter set. To attain the greatest flexibility for device connection, use a cable set.

For devices with 50 Ω Type-N connectors Mechanical calibration kits – 85032F economy: DC to 9 GHz. Includes: 85032-60017 Type-N (m) fixed load 85032-60018 Type-N (f) fixed load 85032-60013 Type-N (m) open 85032-60014 Type-N (f) open 85032-60016 Type-N (m) short 85032-60015 Type-N (f) short – Option 85032F-100 adds: 85032-60021 Type-N (f) to Type-N (f) adapter – Option 85032F-200 adds: 85032-60019 Type-N (m) to Type-N (m) adapter – Option 85032F-300 adds: 85032-60020 Type-N (m) to Type-N (f) adapter – Option 85032F-500 adds: 85054-60001 Type-N (f) to 7 mm adapter (two included) 85054-60009 Type-N (m) to 7 mm adapter (two included) – 85054D economy: DC to 18 GHz. Includes: 85054-60025 Type-N (m) short 85054-60026 Type-N (f) short 85054-60027 Type-N (m) open 85054-60028 Type-N (f) open 85054-60031 Type-N (f) to 7 mm adapter 85054-60032 Type-N (m) to 7 mm adapter 85054-60037 Type-N (f) to Type-N (f) adapter 85054-60038 Type-N (m) to Type-N (m) adapter 85054-60046 Type-N (m) fixed load 85054-60047 Type-N (f) fixed load Electronic calibration kits – 85092C RF ECal: 300 kHz to 9 GHz, 2 ports Includes: Option 85092C-MOF module with: 85092-60008 Type-N (f) to Type-N (m) RF ECal module Option Option 85092C-00M module with: 85092-60009 Type-N (m) to Type-N (m) RF ECal module Option 85092C-00F module with: 85092-60010 Type-N (f) to Type-N (f) RF ECal module Option 85092C-00A adds: 85054-60037 Type-N (f) to Type-N (f) adapter 85054-60038 Type-N (m) to Type-N (m) adapter – N4431B Microwave ECal: 9 kHz to 13.5 GHz, 4 ports1 Includes: Option 020 module with: N4431-60007 4 x Type-N (f) ECal module N4431B-xxx mixed-connector options: Connector type Port A option Port B option Port C option Port D option 3.5 mm (f) 101 201 301 401 3.5 mm (m) 102 202 302 402 Type-N 50 Ω (f) 103 203 303 403 Type-N 50 Ω (m) 104 204 304 404 7-16 (f) 105 205 305 405 7-16 (m) 106 206 306 406 1. Performance from 9 kHz to 300 kHz is valid only for the E5071C ENA network analyzer with firmware version A.09.10 or higher.

– N4432A Microwave ECal: 300 kHz to 18 GHz, 4 ports Includes: Option 020 module with: N4432-60003 4 x Type-N (f) ECal module N4432A-xxx mixed-connector options: Connector type Port A option Port B option Port C option Port D option 3.5 mm (f) 101 201 301 401 3.5 mm (m) 102 202 302 402 Type-N 50 Ω (f) 103 203 303 403 Type-N 50 Ω (m) 104 204 304 404 – N4690B Microwave ECal: 300 kHz to 18 GHz, 2 ports Includes: Option M0F module with: N4690-60001 Type-N (f) to Type-N (m) ECal module Option 00M module with: N4690-60002 Type-N (m) to Type-N (m) ECal module Option 00F module with: N4690-60003 Type-N (f) to Type-N (f) ECal module Option 00A adds: 85054-60037 Type-N (f) to Type-N (f) adapter 85054-60038 Type-N (m) to Type-N (m) adapter Cables – N6314A 50 Ω Type-N RF cable, DC to 12.4 GHz Includes 8120-8862 one 610 mm (24 in) cable with male con- nectors – N6315A 50 Ω Type-N RF cable, DC to 12.4 GHz Includes 8121-0027 one 610 mm (24 in) cable with both female and male connectors Adapters – 11853A 50 Ω Type-N accessory kit. Includes: 1250-1472 Type-N (f) to Type-N (f) adapter (two included) 1250-1475 Type-N (m) to Type-N (m) adapter (two included) 11511A Type-N (f) short 11512A Type-N (m) short – 11878A Type-N to 3.5 mm adapter kit. Includes: 1250-1744 3.5 mm (f) to 50 Ω Type-N (m) adapter 1250-1743 3.5 mm (m) to 50 Ω Type-N (m) adapter 1250-1745 3.5 mm (f) to 50 Ω Type-N (f) adapter 1250-1750 3.5 mm (m) to 50 Ω Type-N (f) adapter – 11524A 7 mm to Type-N (f) adapter – 11525A 7 mm to Type-N (m) adapter – 85130C1,2,3 3.5 mm to Type-N Includes: 85054-60029 NMD-3.5 mm to Type-N (f) 85054-60030 NMD-3.5 mm to Type-N (m) 1. Special rugged female connector specifically for connecting to the net- work analyzer test port, but does not mate with a standard male connector. 2. Recommended to connect H device to E5071C option xD5/xK5 which has NMD-3.5 mm (m) connectors. 3. Consider purchasing Keysight 20mm TORQUE WRENCH 8710-1764

For devices with 3.5 mm or SMA connectors Mechanical calibration kits – 85033E economy: DC to 9 GHz. Includes: 85033-60016 3.5 mm (m) load 85033-60017 3.5 mm (f) load 85033-60018 3.5 mm (m) open 85033-60019 3.5 mm (f) open 85033-60020 3.5 mm (m) short 85033-60021 3.5 mm (f) short 8710-1761 torque wrench Option 85033E-100 adds: 85027-60005 3.5 mm (f) to 3.5 mm (f) adapter Option 85033E-200 adds: 85027-60007 3.5 mm (m) to 3.5 mm (m) adapter Option 85033E-300 adds: 85027-60006 3.5 mm (m) to 3.5 mm (f) adapter Option 85033E-400 adds: 1250-1744 3.5 mm (f) to 50 Ω Type-N (m) adapter 1250-1743 3.5 mm (m) to 50 Ω Type-N (m) adapter 1250-1745 3.5 mm (f) to 50 Ω Type-N (f) adapter 1250-1750 3.5 mm (m) to 50 Ω Type-N (f) adapter Option 85033E-500 adds: 1250-1746 3.5 mm (m) to 7 mm adapter (two included) 1250-1747 3.5 mm (f) to 7 mm adapter (two included) – 85052C precision TRL: DC to 26.5 GHz. Includes: 00902-60003 3.5 mm (m) fixed load 00902-60004 3.5 mm (f) fixed load 85052-60006 3.5 mm (m) short 85052-60007 3.5 mm (f) short 85052-60008 3.5 mm (m) open 85052-60009 3.5 mm (f) open 85052-60032 3.5 mm (f) to 3.5 mm (f) adapter 85052-60033 3.5 mm (m) to 3.5 mm (m) adapter 85052-60034 3.5 mm (f) to 3.5 mm (m) adapter 85052-60035 3.5 mm short TRL line 85052-60036 3.5 mm long TRL line – 85052D economy: DC to 26.5 GHz. Includes: 00902-60003 3.5 mm (m) fixed load 00902-60004 3.5 mm (f) fixed load 85052-60006 3.5 mm (m) short 85052-60007 3.5 mm (f) short 85052-60008 3.5 mm (m) open 85052-60009 3.5 mm (f) open 85052-60012 3.5 mm (f) to 3.5 mm (f) adapter 85052-60013 3.5 mm (f) to 3.5 mm (m) adapter 85052-60014 3.5 mm (m) to 3.5 mm (m) adapter Electronic calibration kits – 85093C RF ECal: 300 kHz to 9 GHz, 2 ports Standard module includes: Option M0F with: 85093-60008 3.5 mm (f) to 3.5 mm (m) ECal module Option 00F module with: 85093-60010 3.5 mm (f) to 3.5 mm (f) ECal module Option 00M module with: 85093-60009 3.5 mm (m) to 3.5 mm (m) ECal module Option 00A adds: 85052-60012 3.5 mm (f) to 3.5 mm (f) adapter 85052-60014 3.5 mm (m) to 3.5 mm (m) adapter 85093C-xxx mixed-connector options: Port A option Port B option Type (f) (m) Type (f) (m) Type (f) (m) 3.5 mm 101 102 Type-N 203 204 7-16 205 206 – N4431B Microwave ECal: 9 kHz to 13.5 GHz, 4 ports1 Includes: Option 010 module with: N4431-60006 4 x 3.5 mm (f) ECal module N4431B-xxx mixed-connector options: Connector type Port A option Port B option Port C option Port D option 3.5 mm 201 301 401 3.5 mm (m) 102 202 302 402 Type-N 50 Ω (f) 103 203 303 403 Type-N 50 Ω (m) 104 204 304 404 7-16 (f) 105 205 305 405 7-16 (m) 106 206 306 406 – N4433A Microwave ECal: 300 kHz to 20 GHz, 4 ports Includes: Option 010 module with: N4433-60003 4 x 3.5 mm (f) ECal module 1. Performance from 9 kHz to 300 kHz is valid only for the E5071C ENA network analyzer with firmware version A.09.10 or higher.

1. Special rugged female connector specifically for connecting to the network analyzer test port, but does not mate with a standard male con- nector. 2. 1250-1744 3.5 mm (f) to 50 Ω Type-N (m) adapters are recommended to connect to the E5071C Option x4x, x6x, and x8x test ports, which have Type-N (f) connectors. 3. NMD-3.5 mm (f) to 3.5 mm (f), or 3.5 mm (f) to 3.5 mm (f) adapters are recommended to connect to the E5071C Option xD5, xK5, which have NMD-3.5 mm (m) connectors. 4. Consider purchasing Keysight 20mm TORQUE WRENCH 8710-1764 N4433A-xxx mixed-connector options: Connector type Port A option Port B option Port C option Port D option 3.5 mm (f) 101 201 301 401 3.5 mm (m) 102 202 302 402 – N4691B Microwave ECal: 300 kHz to 26.5 GHz, 2 ports. Includes: Option M0F module with: N4691-60001 3.5 mm (f) to 3.5 mm (m) ECal module Option 00M module with: N4691-60002 3.5 mm (m) to 3.5 mm (m) ECal module Option 00F module with: N4691-60003 3.5 mm (f) to 3.5 mm (f) ECal module Option 00A adds: 85052-60012 3.5 mm (f) to 3.5 mm (f) adapter 85052-60014 3.5 mm (m) to 3.5 mm (m) adapter Cables – 11500E2, 3, 4 cable, APC 3.5 mm (m), DC to 26.5 GHz Includes: one 610 mm (24 in) with male connectors. – 11500F2, 3, 4 150 cm cable, APC 3.5 mm (m), DC to 26.5 GHz Includes: one 1520 mm (60 in) with male connectors. – 85131C1, 4 single, semi-rigid: 3.5 mm (f) to PSC-3.5 mm (f), 81 cm, 32 inches – 85131D1. 4 set, semi-rigid: 85131-60009 one 3.5 mm (f) to 3.5 mm (m), 53 cm, 21 inches, – 85131-60010 one 3.5 mm (f) to PSC-3.5 mm (f), 53 cm, 21 inches – 85131E1, 4 single, flexible: 3.5 mm (f) to PSC-3.5 mm (f), 96.5 cm, 38 inches – 85131F1, 4 set, flexible: – 85131-60012 one 3.5 mm (f) to 3.5 mm (m), 62.2 cm, 24.5 inches – 85131-60013 one 3.5 mm (f) to PSC-3.5 mm (f), 62.2 cm, 24.5 inches – 85131G1, 4 single, semi-rigid: 3.5 mm (f) to 3.5 mm (m), 53 cm, 21 inches – 85131H1, 4 single, flexible: 3.5 mm (f) to 3.5 mm (m), 62.2 cm, 24.5 inches – 85134C1 single, semi-rigid: PSC-3.5 mm (f) to 2.4 mm (f), 81 cm, 32 inches – 85134D1 set, semi-rigid: – 85134-60002 one 2.4 mm (f) to PSC-3.5 mm (f), 53 cm, 21 inches – 85134-60001 one 2.4 mm (f) to PSC-3.5 mm (m), 53 cm, 21 inches – 85134E1 single, flexible: PSC-3.5 mm (f) to 2.4 mm (f), 96 cm, 38 inches – 85134F1 set, flexible: 85134-60004 one 2.4 mm (f) to PSC-3.5 mm (f), 61 cm, 24 inches 85134-60003 one 2.4 mm (f) to PSC-3.5 mm (m), 61 cm, 24 inches – 85134G1 single, semi-rigid: 2.4 mm (f) to PSC-3.5 mm (m), 53 cm, 21 inches – 85134H1 single, flexible: 2.4 mm (f) to PSC-3.5 mm (m), 61 cm, 24 inches – N4419AK20 single, flexible: 3.5 mm (m) to 3.5 mm (f), 91.4 cm, 36 inches – Z5623A-K20 single, flexible: 3.5 mm (m) to 3.5 mm (m), 91.4 cm, 36 inches Adapters – 11853A 50 Ω Type-N accessory kit. Includes: 1250-1472 Type-N (f) to Type-N (f) adapter (two included) 1250-1475 Type-N (m) to Type-N (m) adapter (two included) 85032-60009 Type-N (f) short 85032-60008 Type-N (m) short – 11878A Type-N to 3.5 mm adapter kit. Includes: 1250-1744 3.5 mm (f) to 50 Ω Type-N (m) adapter 1250-1743 3.5 mm (m) to 50 Ω Type-N (m) adapter 1250-1745 3.5 mm (f) to 50 Ω Type-N (f) adapter 1250-1750 3.5 mm (m) to 50 Ω Type-N (f) adapter – 11524A 7 mm to Type-N (f) adapter – 11525A 7 mm to Type-N (m) adapter – 85130C1 3.5 mm to Type-N Includes: 85054-60029 NMD-3.5 mm to Type-N (f) 85054-60030 NMD-3.5 mm to Type-N (m) – 85130D1 3.5 mm to 3.5 mm Includes: 85130-60005 NMD-3.5 mm to PSC-3.5 mm (f) 85130-60006 NMD-3.5 mm to PSC-3.5 mm (m) – 85130F1 2.4 mm to 3.5 mm

1. For this option order K281C-012. For devices with 75 Ω Type-N connectors Mechanical calibration kits – 85036B DC to 3 GHz, includes: 00909-60019 75 Ω Type-N (m) broadband load 00909-60020 75 Ω Type-N (f) broadband load 85036-60012 75 Ω Type-N (m) short 85036-60011 75 Ω Type-N (f) short 85032-60007 75 Ω Type-N (m) open 85032-20001 75 Ω Type-N (f) open body 85036-60010 75 Ω Type-N (f) open center conductor extender 85036-60013 75 Ω Type-N (m) to (m) adapter 85036-60014 75 Ω Type-N (f) to (f) adapter 85036-60015 75 Ω Type-N (m) to (f) adapter – 85036E DC to 3 GHz, includes: 00909-60019 75 Ω Type-N (m) broadband load 85036-60016 75 Ω Type N (m) combined open/short Adapters – 11852B Minimum-loss pad Option 11852B-004 Type-N connectors, 50 Ω (m) to 75 Ω (f) Calibration must be done with a 75 Ω calibration kit using an 11852B minimum-loss pad, and impedance conversion to 75 Ω using the ENA’s fixture simulator function is required. For devices with waveguide Mechanical calibration kits X Band – X11644A standard, WR-90: 8.2 to 12.4 GHz. Includes: 00896-60008 X-band standard section 00910-60003 X-band termination 11644-20018 X-band short 11644-20021 X-band shim – 85132F cable set (set of 2, flexible 7 mm to 3.5 mm, 62.9 cm each, 24.75 inches each) – 85135F cable set (set of 2 , flexible, 7 mm to 2.4 mm, 53 cm each, 21 inches each) – X281C adapter (included in calibration kit): WR-90 to 7 mm P Band – P11644A standard, WR-62: 12.4 to 18 GHz. Includes: 00896-60007 P-band standard section 00910-60002 P-band termination 11644-20017 P-band short 11644-20020 P-band shim – 85132F cable set (set of 2, flexible, 7 mm to 3.5 mm, 62.9 cm each, 24.75 inches each) – 85135F cable set (set of 2, flexible, 7 mm to 2.4 mm, 53 cm each, 21 inches each) – P281C adapter (included in calibration kit): WR-62 to 7 mm K Band – K11644A standard, WR-42: 18 to 26.5 GHz. Includes: 00896-60006 K-band standard section 00910-60001 K-band termination 11644-20016 K-band short 11644-20019 K-band shim – 85134F cable set (set of 2, flexible, 3.5 mm to 2.4 mm, 53 cm each, 21 inches each) – K281C adapter (included in calibration kit): WR-42 to 3.5 mm (f) Option 0121 WR-42 to 3.5 mm (m)

1. Order the 82357B USB/GPIB interface to control a power meter by the E5071C. 2. To use the U200x USB power sensors for source power calibration, the E5071C ENA firmware version A.09.2x or higher is required. Additional Accessories Power limiters – N9355B power limiter, 10 dBm limiting threshold, 10 MHz to 18 GHz, Type-N – N9356B power limiter, 25 dBm limiting threshold, 10 MHz to 18 GHz, Type-N – N9355C power limiter, 10 dBm limiting threshold, 10 MHz to 26.5 GHz, 3.5 mm – N9356C power limiter, 25 dBm limiting threshold, 10 MHz to 26.5 GHz, 3.5 mm DC blocks – N9398C DC block, 16 V maximum working voltage, 50 kHz to 26.5 GHz, 3.5 mm – N9399C DC block, 50 V maximum working voltage, 700 kHz to 26.5 GHz, 3.5 mm – 11742A, 50 V maximum working voltage, 45 MHz to 26.5 GHz, 3.5 mm Amplifiers – 87405B pre-amplifier, 22 dB gain, 10 MHz to 4 GHz – 87405C pre-amplifier, 25 dB gain, 100 MHz to 18 GHz – 87415A amplifier, 25 dB gain, 2 to 8 GHz – 83006A amplifier, 20 dB gain, 10 MHz to 26.5 GHz Attenuators – 8491A fixed attenuator, DC to 12.4 GHz, Type-N – 8493A fixed attenuator, DC to 12.4 GHz, SMA RF & microwave switches – N1810TL SPDT switch, terminated, DC to 26.5 GHz – N1810UL SPDT switch, unterminated, DC to 26.5 GHz – 87104B SP4T switch, terminated, DC to 20 GHz – 87106B SP6T switch, terminated, DC to 20 GHz – 87222C transfer switch, DC to 26.5 GHz – L7104B SP4T switch, terminated, DC to 20 GHz – L7106B SP6T Switch, terminated, DC to 20 GHz – L7222C transfer switch, DC to 26.5 GHz – P9400C solid state PIN diode transfer switch, 100 MHz to 18 GHz – P9402C SPDT solid state PIN diode switch, 100 MHz to 18 GHz – P9404C SP4T solid state PIN diode switch, 100 MHz to 18 GHz – U9397C SPDT solid state FET hybrid switch, 300 kHz to 18 GHz – U9400C solid state FET hybrid transfer switch, 300 KHz to 18 GHz Power meters and sensors1 Recommended for source output power calibration. – E4416A1 single-channel EPM-P series power meter – E4417A1 dual-channel EPM-P series power meter – E4418B1 single-channel EPM series power meter – E4419B1 dual-channel EPM series power meter – N1911A1 single-channel P-series power meter – N1912A1 dual-channel P-series power meter – 8482A power sensor, 100 kHz to 4.2 GHz, Type-N (m), 100 mW – E9304A-H18 power sensor, 9 kHz to 18 GHz, Type-N (m), 100 mW – E4412A CW power sensor, 10 MHz to 18 GHz, Type-N (m), 200 mW – E4413A CW power sensor, 50 MHz to 26.5 GHz, 3.5 mm (m), 200 mW – N1921A power sensor 50 MHz to 18 GHz, Type-N (m) – N1922A power sensor 50 MHz to 40 GHz, 2.4 mm (m) – U2000A/B/H2 USB power sensor, 10 MHz to 18 GHz, Type-N (m) – U2001A/B/H2 USB power sensor, 10 MHz to 6 GHz, Type-N (m) – U2002A/H2 USB power sensor, 50 MHz to 24 GHz, 3.5 mm (m) – U2004A2 USB power sensor, 9 kHz to 6 GHz, Type-N (m) Probes – N1021B 18 GHz differential TDR/TDT passive probe kit – 85024A high-frequency probe, 300 kHz to 3 GHz General accessories System racks – 1CN005A handle kit, may be ordered as option 1CN (two included) – 1CM015A rack mount kit, for use without handles: may be ordered as option 1CM – 1CP009A rack mount kit, for use with previously supplied handles; may be ordered as option 1CP – E3663AC rack mount rail kit, for use with 1CM015A or 5188-4430 – 1181BZ test mobile system cart Interface cables The following GPIB cables can be used to connect the network analyzer with an external device such as a computer – 10833A GPIB cable, 1.0 m (3.3 ft) – 10833B GPIB cable, 2.0 m (6.6 ft) – 10833C GPIB cable, 4.0 m (13.1 ft) – 10833D GPIB cable, 0.5 m (1.6 ft) – 82357B GPIB to USB interface, necessary to control a power meter or signal generator with the E5071C. Monitors – XGA-compatible monitor Printers – USB printers with Microsoft Windows printer driver Other – 8710-1764 WRENCH - TORQUE 8 IN/LB, 20 MM OPEN END

Upgrade kits Upgrade kits for the E5071C Protecting your hardware investment The E5071C ENA network analyzer is a safe investment because of its flexibility. Easily upgrade any ENA software or hardware feature whenever you need that feature. Ordering instructions To upgrade an existing E5071C, order the corresponding upgrade kit model. For further information, visit: http://www.keysight.com/find/ena_upgrades Application and product notes Introduction to the Fixture Simulator Function of the ENA Series RF Network Analyzers: Network De-embedding/Embedding and Balanced Measurement, Product Note E5070/71-1 Literature number 5988-4923EN Evolution of Test Automation Using Built-in VBA with the ENA Series RF Network Analyzers, Product Note E5070/71-2 Literature number 5988-6192EN On-wafer Multiport Calibration Using the ENA Series RF Network Analyzer with the Cascade Microtech Probing System, Product Note E5070/71-3 Literature number 5988-5886EN In-Fixture Characterization Using the ENA Series RF Network Analyzer with Cascade Microtech Probing System, Product Note E5070/71-4 Literature number 5988-6522EN Improve the Circuit Evaluation Efficiency of Wireless LAN Chip Set Design, Application Note 1463-2 Literature number 5988-9803EN Impedance Characteristic Evaluation of SMD by Using the ENA with Inter-Continental Microwave (ICM) Application Note 1463-5 Literature number 5989-0547EN Accurate Mixer Measurements Using the Frequency-Offset Mode, Application Note 1463-6 Literature number 5989-1420EN 7 Reasons to Migrate from Your 8753 to an ENA Network Ana- lyzer Application Note 1478 Literature number 5989-0206EN Multiport Solutions for E5071C ENA RF Network Analyzers Using External Switches Literature number 5989-7916EN Advanced Measurement Techniques for RF Amplifiers Using Unique Functions of the Keysight E5071C ENA Literature number 5989-6522EN Measurement Wizard Assistant software for ENA/E5091A Literature number 5989-4855EN Comprehensive Multiport Solution for the ENA Network Analyzer Literature number 5989-8737EN E5071C ENA Option TDR Enhanced Time Domain Analysis Option Literature number 5990-5237EN Correlation between TDR oscilloscope and VNA generated time domain waveform Literature number 5990-5238EN Literature and information ENA Network Analyzers Brochure Literature number 5989-5478EN ENA Network Analyzers Data Sheet Literature number 5989-5479EN Keysight Network Analyzer Selection Guide Literature number 5989-7603EN ENA-L RF Network Analyzers Brochure Literature number 5989-0167EN ENA-L RF Network Analyzers Data Sheet Literature number 5989-0018EN Test Solutions for Multiport and Balanced Devices Selection Guide Literature number 5988-2461EN Keysight RF & MW Test Accessories Catalog Literature number 5968-4314EN Key web resources for additional infor- mation on the ENA Series, visit: www.keysight.com/find/ena

This information is subject to change without notice. © Keysight Technologies, 2013 - 2015 Published in USA, March 25, 2015 5989-5480EN www.keysight.com myKeysight www.keysight.com/find/mykeysight A personalized view into the information most relevant to you. www.axiestandard.org AdvancedTCA® Extensions for Instrumentation and Test (AXIe) is an open standard that extends the AdvancedTCA for general purpose and semiconductor test. Keysight is a founding member of the AXIe consortium. ATCA®, AdvancedTCA®, and the ATCA logo are registered US trademarks of the PCI Industrial Computer Manufacturers Group. www.lxistandard.org LAN eXtensions for Instruments puts the power of Ethernet and the Web inside your test systems. Keysight is a founding member of the LXI consortium. www.pxisa.org PCI eXtensions for Instrumentation (PXI) modular instrumentation delivers a rugged, PC-based high-performance measurement and automation system. Three-Year Warranty www.keysight.com/find/ThreeYearWarranty Keysight’s commitment to superior product quality and lower total cost of ownership. The only test and measurement company with three-year warranty standard on all instruments, worldwide. Keysight Assurance Plans www.keysight.com/find/AssurancePlans Up to five years of protection and no budgetary surprises to ensure your instruments are operating to specification so you can rely on accurate measurements. www.keysight.com/go/quality Keysight Technologies, Inc. DEKRA Certified ISO 9001:2008 Quality Management System Keysight Channel Partners www.keysight.com/find/channelpartners Get the best of both worlds: Keysight’s measurement expertise and product breadth, combined with channel partner convenience. For more information on Keysight Technologies’ products, applications or services, please contact your local Keysight office. The complete list is available at: www.keysight.com/find/contactus Americas Canada (877) 894 4414 Brazil 55 11 3351 7010 Mexico 001 800 254 2440 United States (800) 829 4444 Asia Pacific Australia 1 800 629 485 China 800 810 0189 Hong Kong 800 938 693 India 1 800 11 2626 Japan 0120 (421) 345 Korea 080 769 0800 Malaysia 1 800 888 848 Singapore 1 800 375 8100 Taiwan 0800 047 866 Other AP Countries (65) 6375 8100 Europe & Middle East Austria 0800 001122 Belgium 0800 58580 Finland 0800 523252 France 0805 980333 Germany 0800 6270999 Ireland 1800 832700 Israel 1 809 343051 Italy 800 599100 Luxembourg +32 800 58580 Netherlands 0800 0233200 Russia 8800 5009286 Spain 800 000154 Sweden 0200 882255 Switzerland 0800 805353 Opt. 1 (DE) Opt. 2 (FR) Opt. 3 (IT) United Kingdom 0800 0260637 For other unlisted countries: www.keysight.com/find/contactus (BP-02-20-15)