CDA SK700 Installation, Use And Maintenance Manual

• The cooking function knob is set to a function. • The oven door is opened (it will remain on for approximately 10 minutes). • You touch the oven light sensor if the light is not already on. The interior light should deactivate when: • The cooking function knob is set to the off position ‘ ’ and the door is closed. • Automatically after 30 seconds if the door is closed or 10 minutes if the door is open. • You touch the oven light sensor if the light is not already off. You can set the interior light to come on perman ...

• Hold the door to the appliance in the closed position and manoeuvre the hinges so that the part of the hinge, highlighted by the star in fig. 3, inserts into the hinge slot in the cavity frame. • Next, ensure the notch on the underside of the hinge sits on the lip of the hinge slot. Open the door fully. Each hinge should be seated in the same way as the hinge in fig. 4. If it is not, follow the steps for removing the door and try replacing it again. • Finally, lift the safety catch part of the hinges back into place so that they are lying flat against th ...

right to change specifications without prior notice. Energy Efficiency Information Attribute Symbol Value Units Model identification SK700 Mass of the appliance M 33.6 kg Energy efficiency index (EEI cavity) 87.1 Energy efficiency class A+ Number of cavities 1 Heat source per cavity (electricity or gas) Electricity Volume per cavity V 65 L Energy consumption (electricity) required to heat a standardised load in a cavity of an electric heated oven during a cycle in conventional mode per ...

When correctly installed ensure that there is a gap of 4 mm minimum between the sides of the oven and adjacent furniture doors. How to install your oven You will need the housing area in fig. 15 to fit your oven correctly. The oven is designed to fit into a cabinet of 600 mm width. The oven can be built in or built under the kitchen units, but you must ensure that it is properly ventilated. In the diagram below the built-in oven is ventilated by means of a space at the top of the kitchen cabinet. There are many other methods of ventilating your oven - consult a qualified engin ...

When correctly installed ensure that there is a gap of 4 mm minimum between the sides of the oven and adjacent furniture doors. How to install your oven You will need the housing area in fig. 15 to fit your oven correctly. The oven is designed to fit into a cabinet of 600 mm width. The oven can be built in or built under the kitchen units, but you must ensure that it is properly ventilated. In the diagram below the built-in oven is ventilated by means of a space at the top of the kitchen cabinet. There are many other methods of ventilating your oven - consult a qualified engin ...

Keeping your oven clean and well maintained helps to prolong the fault-free lifespan of it. It is important that, before any cleaning or maintenance is performed, you switch off the oven at the mains supply. Do not start any cleaning or maintenance until the oven has been allowed to cool completely. We recommend always wearing PPE (Personal Protective Equipment) when carrying out any cleaning or maintenance. Cleaning the oven exterior As the oven has a stainless steel or enamel surface, you should use a nonabrasive cleaner. Any abrasive cleaner (including Cif) will ...

CDA Customer Care to arrange a repair. Contact details are below. Please have to hand all the details from your appliance’s rating plate which can be found on the back of the oven and/or on the back of the instruction manual/warranty card. Important: All repairs must be carried out by CDA authorised service technicians. Contact CDA Customer Care A: Customer Care Department, The CDA Group Ltd, Harby Road, Langar, Nottinghamshire, NG13 9HY T: 01949 862 012 F: 01949 862 003 E: [email protected] W: ww ...

Whilst installing the oven, you may wish to adjust the final position of the door. The following allows for ± 1.5mm adjustment: • Loosen the nut (1) with a size 13 spanner. • Use a size 4 allen key to rotate the spindle (2) in a 180° range. • Once adjustment is complete, tichen the nut (1) whilst holding the allen key in place in the spindle (2). Mains electrical connection Warning! This appliance must be earthed. This appliance is intended to be connected to fixed wiring by a double pole switch, having a contact separation of at least 3mm in all poles and pr ...