DeWalt LaserChalkLine DW088 Instruction Manual

Text of DeWalt LaserChalkLine DW088 Instruction Manual

If you have questions or comments, contact us.

Pour toute question ou tout commentaire, nous contacter. Si tiene dudas o comentarios, contáctenos. 1-800-4-DeWALT Instruction Manual Guide D’utilisation Manual de instrucciones Manual de Instruções DW088, DW088CG LaserChalkLine™ Laser Line Generator Générateurs de faisceaux laser LaserChalkLineMC Generador de línea láser LaserChalkLine™ Gerador de Linha Laser LaserChalkLine™ Final page size: A5

If you have any questions or comments about this or any DeWALT tool, call us toll free at: 1-800-4-DeWALT

(1-800-433-9258). Safety Instructions for Lasers WARNING! Read and understand all instructions. Failure to follow all instructions listed below may result in electric shock, fire and/or serious personal injury. SAVE THESE INSTRUCTIONS � WARNING! Laser Radiation Exposure. Do not disassemble or modify the laser level. There are no user serv

For your convenience and safety, the following label is on your laser.

� CAUTION: LASER RADIATION - DO NOT STARE INTO THE LASER BEAM. CLASS II LASER PRODUCT. � CAUTION: CLASS 2 LASER RADIATION WHEN OPEN DO NOT STARE INTO THE BEAM. Made in China Complies with 21 CFR 1040.10 and 1040.11 except for deviations pursuant to Laser Notice No. 50, dated June 24, 2007 DeWALT Industrial Tool CO. Towson, MD 21286 USA For service informa

To install batteries:

1. Lift up the battery compartment cover  1  as shown in Figure A. 2. Insert three fresh AA batteries in the compartment, placing the batteries according to Fig. A – + + 1 (+) and (–) on the inside of the battery door. � WARNING: Batteries can explode, or leak, and can cause injury or fire. To reduce this risk: • Carefully follow all instructions and warnings on the battery label and package. • Always insert

Low Battery Indication

The DW088 lasers are equipped with a red indicator light  2 , as shown in Fig. B DW088 2 3 4 Figure B. The red indicator lights are located to the left of the on/off buttons   3 ,  4  . A flashing red indicator light indicates that the batteries are low and need to be replaced. The laser may continue to operate for a short time while the batteries continue to drain, but the beam(s) will quickly dim. After fresh bat

Using the Laser with the Wall Mount (Fig. E)

The DW0860 Laser Wall Mount offers more mounting options for the DW088 lasers. The wall mount has a clamp  7  at one end which can be fixed to a wall angle for acoustic ceiling installation. At the other end of the wall mount is a screw hole  8 , allowing the wall mount to be attached to any surface with a nail or screw. Once the wall mount is secured, its steel plate provides a surface to which th

Checking Accuracy – Horizontal Beam, Pitch Direction (Fig. G)

Checking the horizontal pitch calibration of the laser requires a single wall at least 30’ (9 m) long. It is important to conduct a calibration check using a distance no shorter than the distance of the applications for which the tool will be used. 1. Attach the laser to one end of a wall using its pivot bracket. 2. T

Distance Between Walls

Allowable Distance Between Marks 30’ (9 m) 1/4” (6.0 mm) 40’ (12 m) 5/16” (8.0 mm) 50’ (15 m) 13/32” (10.0 mm) Checking Accuracy – Vertical Beam (Fig. H) Checking the vertical (plumb) calibration of the laser can be most accurately done when there is a substantial amount of vertical height available, ideally 30’ (9m), with one person on the floor positioning the laser and another person near a ceiling to mar

DeWalt Measuring Instruments Owners Instructions: