Fluke 05-450 Operation & User’s Manual

© 2014 Fluke Corporation. All rights reserved. Specifications are subject to change without notice. All product names are trademarks of their respective companies. 05-450 Digital Doorway Monitor Users Manual ...

Fluke Biomedical warrants this instrument against defects in materials and workmanship for one year from the date of original purchase OR two years if at the end of your first year you send the instrument to a Fluke Biomedical service center for calibration. You will be charged our customary fee for such calibration. During the warranty period, we will repair or at our option replace, at no charge, a product that proves to be ...

 Copyright 2014, Fluke Biomedical. No part of this publication may be reproduced, transmitted, transcribed, stored in a retrieval system, or translated into any language without the written permission of Fluke Biomedical. Copyright Release Fluke Biomedical agrees to a limited copyright release that allows you to reproduce manuals and other printed materials for use in service training programs and other technical publications ...

be calibrated at least once every 12 months. Calibration must be done by qualified personnel. Contact your local Fluke Biomedical representative for calibration. Certification This instrument was thoroughly tested and inspected. It was found to meet Fluke Biomedical’s manufacturing specifications when it was shipped from the factory. Calibration m ...

Title Page Introduction ............................................................................................ 1 Safety Information ................................................................................. 3 Symbols ................................................................................................. 4 General Specifications ....................................................................... 5 Driver Op ...

Optional Remote Alarms ............................................................... 18 Maintenance .......................................................................................... 18 Cleaning Instructions and Precautions .............................................. 18 Replacement of Mains Fuse ..................... ...

Figure Title Page 1. Front Panel ................................................................................................ 2 2. Left Side-Panel .......................................................................................... 7 3. Alarm Point Notice ..................................................................................... 8 4. Typical Installation 385x442 .................................................. ...

designed to monitor for nuclear radiation. Featuring a wall-mount chassis, the Product has a four-digit LED display that is readable from 9 m (30 ft) away. Backlit indicators warn of low radiation alarm (yellow), high radiation alarm (red), instrument failure (red) and low battery (yellow). A green status light is a positive indication of instrument operation. Parameters a ...

Safety Information 3 Safety Information A Warning identifies conditions and procedures that are dangerous to the user. A Caution identifies conditions and procedures that can cause damage to the Product or the equipment under test. Warning To prevent possible electrical shock, fire, or personal injury: • Read all safety information before you use the Product. • Carefully read all instructions. • Do not use the Product ar ...

replace battery. • Do not touch the circuit board in the calibration window due to potential for electric shock. • Do not touch the center pin of the detector connector unless the unit has been turned off and power has been removed or at least 1 minute. • To prevent contact with internal hazardous live parts that are accessible using a tool: turn off the Product and d ...

General Specifications 5 General Specifications Detectors .................................................................. Two 7.6 cm x 2.5 cm (3 in x 1 in) thick, shielded NaI (T1) scintillation detectors with up to 200 ft cables (NEMA 4x enclosures included.) Display ...................................................................... 4-digit LED display with 2 cm (0.8 in.) character height Display Range ..................... ...

-40 °C to 65 °C (-40 °F to 150 °F) Maximum relative humidity .................................... Less than 95% (non-condensing) Size Electronics (H x W x D) .......................................... 24.6 cm x 18.7 cm x 6.4 cm (9.7 in x 7.4 in x 2.5 in) Detectors (H x W x D) ............ ...

Getting Started 7 Getting Started The Product is designed for ease of use. This section of the manual is designed to help the first-time user get started. Initial power-up and basic features of the instrument are contained in this section. Other sections of the manual provide more detailed information Power Up Plug the power cord into a suitable wall (Mains) outlet. Note The Product will normally be wired internally for 120 V ac. If ...

to conform to your requirements. The factory-set alarm points may be incorrect for your use. Refer to the instrument manual for more information on setting alarm points. FAILURE TO RESET THE ALARM POINT(S) MAY RESULT IN EXCESSIVE ALARMS OR LACK OF SENSITIVITY. huk02.eps Figure 3. Alarm Point Notice Initial power-up will momentarily activate the internal front-panel lights, sound the aud ...

Getting Started 9 Setting Alarm-Points The LOW ALARM and HIGH ALARM points can only be changed while the instrument is in calibration mode. Switch the top dipswitch CAL MODE (behind the calibration cover) to the right to place the instrument into calibration mode. Changing alarm points is done by holding down the corresponding parameter key and pressing the up or down arrow buttons. Alarm points can be set in the range of 0.1 to 999 ...

Calibration Controls Remove the calibration cover to expose the calibration controls. The calibration controls include the up/down buttons, five calibration potentiometers, and the option dipswitch (detailed in the following subsection). The five potentiometers are detailed below: Warning To prevent possible electrical shock, fire, or personal injury: • To prevent contact with internal hazardous li ...

Operator Controls and Setup 11 Dipswitch (under calibration cover) When the calibration cover is removed, a four-pole dipswitch is accessible that can activate or deactivate options. These four options are: CAL MODE, LATCH ALARM, RANGE, and SINGLE BEEP. • Dipswitch 1: Switching the top CAL MODE switch to the right places the instrument into calibration mode. Parameters can only be changed while the instrument is in calibration mod ...

data onto pin 4 of the 9-pin connector every 2 seconds. An example program which shows how an IBM compatible PC can be used to collect the data follows: ‘Demonstration Program ‘Model 05-450 communication program written for QuickBasic ‘This program causes the computer screen to display the data being dumped from the Model 05-450. ‘Needs t ...