JAGER PRO M.I.N.E. Operator's Manual

Our AT&T camera is designed to test program settings and IMEI service by manually sending a photo. Move the selector switch from OFF to SETUP. Allow the camera 30 seconds to search the wireless AT&T network. AT&T will appear in the top center of the LCD screen after connecting. Press the OK button to immediately capture a photo. Press the OK button again to upload the image to the network by following the camera program settings. The automatic commands displayed in the bottom center of the LCD screen are “Setting”, “Sending” followed by “Sent”. This proces ...

decibel booster antenna is available as an accessory for operation in low signal areas. 1a. Antenna Seal: Prevents water from getting into the camera through the antenna port (see page 7). 2. IR Illuminator: 44 infrared LEDs that illuminate the target area when camera functions at night. 3. Ambient Light Sensor: Detects surrounding light to automatically control day and night camera functions. This sensor also emits a green, blinking LED when the selector switch is moved to SET ...

technology to GSM, which is the world’s most widely used cell phone standard. Sprint, Verizon, and Virgin Mobile use CDMA. GPRS- General Packet Radio Service was early technology to enable data communication on GSM networks. It has since been replaced by better data technologies such as EDGE and 3G. It is based on GSM and compliments SMS. GSM- Global System for Mobile communications. Cell phones use a cellular provider’s GSM network by searching for cellular phone towers in the nearby area. GSM has more compl ...

This antenna is designed for areas where cellular coverage is weak and enables users to expand the usable range of the M.I.N.E.™ Cam. • 5 db gain for remote areas • 2.5 feet mast allows for higher vertical reach in terrain such as valleys and thick tree cover •10.5 feet coaxial cable is designed for high quality signal transmission while providing flexibility to mount on a 16’ tall telescoping pole. T- Post Camera Mount Allows the M.I.N.E.™ Cam to easily mount in remote locations and above trap panels using a T-Post. • Aluminum ...

and defects in both materials and workmanship for one (1) year from the date of purchase (“Warranty Period”). JAGER PRO™, LLC will repair or replace, at its option, the Product if it fails to function properly during the Warranty Period, subject to the conditions and/or limitations stated herein. Such repair or replacement is your sole remedy under this Limited Warranty. Limitations: Limited Warranty service will not be provided unless the Product, returned in the manner set forth below, is a ...

1 1. SIM Card Port: Slot for receiving a cellular SIM card from GSM network providers such as AT&T and T-Mobile. 2. SD Card Port: Slot for receiving an SD card. The camera has no internal memory. A 32GB or smaller SD card must be used to store photos, video and data. Warning! Inserting the memory card upside down or backwards could damage the camera or the memory card. Damage resulting from inserting the card incorrectly is not covered under warranty. QUICK START PROGRAMMING Begin programming the M.I.N.E™ Camera for operation by removing the red or yellow shipping plug and r ...

CONTROL BOX RECEIVER THIS STEP IS ONLY A FUNCTION OF THE M.I.N.E.™ CAMERA. THE I.C.E.™ CAMERA DOES NOT UTILIZE AN INTERNAL TRANSMITTER. The M.I.N.E.™ Camera has an internal transmitter on the circuit board and must be located within 50 meters of the M.I.N.E.™ Gate to operate correctly. Users must manually calibrate the camera transmitter signal to each control box receiver the first time they are paired together. One camera will operate multiple control box receivers to trigger multiple gates simultaneously at a trap enclosure. 1. Move camera selector sw ...

CONTROL BOX RECEIVER THIS STEP IS ONLY A FUNCTION OF THE M.I.N.E.™ CAMERA. THE I.C.E.™ CAMERA DOES NOT UTILIZE AN INTERNAL TRANSMITTER. The M.I.N.E.™ Camera has an internal transmitter on the circuit board and must be located within 50 meters of the M.I.N.E.™ Gate to operate correctly. Users must manually calibrate the camera transmitter signal to each control box receiver the first time they are paired together. One camera will operate multiple control box receivers to trigger multiple gates simultaneously at a trap enclosure. 1. Move camera selector sw ...