APART REVAMP2250 Instruction Manual

Text of APART REVAMP2250 Instruction Manual

DIGITAL POWER AMPLIFIER

APART REVAMP2250 Cooling convectional Max power consumption 600 W Operating temperature range 0 to 40°C Mains operating voltage 230 VAC / 50 - 60 Hz (115VAC with internal jumper) Dimensions 483 x 44 x 235 mm ( including rack ears) Net weight 3.1 kg Gross weight 4.9 kg ...

Dynamic output power

APART REVAMP2250 2 x 350 W @ 4 Ω Sine wave power per channel 250 W @ 4 Ω (500 msec) Dynamic output power bridged 700 W @ 8 Ω Sine wave power bridged 500 W @ 8 Ω Minimum output load impedance CH1 and CH2 4 Ω Minimum output load impedance bridge mode 8 Ω Input connections 2 x balanced ...

Industriepark Brechtsebaan 8 bus 1

APART REVAMP2250 2900 Schoten - Belgium Company names, product names and trademarks are property of their respective owners. Apart-Audio specifications are subject to change without notice. ...

Unbalanced inputs on RCA with pass through

APART REVAMP2250 • Input level attenuators on all inputs • 4-pole Speakon® speaker output connectors • Euroblock speaker output connectors • Extended speaker and amp protection circuits: DC protect, over current protect, over temperature protect, input overload • Individual channel mu ...

!!! IMPORTANT !!!

This amplifier relies on convectional cooling only. In normal situations, overheating will not occur due to the class D amplifier topology. Since there are no cooling fans in the amplifier, make sure the convectional cooling system can work properly. The unit can be built in a 19 inch rack system, but it is ...

Set level controls on amplifiers all the way down during power-

APART REVAMP2250 up to prevent speaker damage if there are high signal levels at the inputs. • Do not connect the inputs / outputs of amplifiers or consoles to any other voltage source, such as a battery, mains source, or power supply, regardless of whether the amplifier o ...

DIGITAL POWER AMPLIFIER

Features • 1 rack unit high • High power Hypex® class-D power amplifier modules • Bridgeable 2 channel amplifier • Dynamic output power: 2x350W @ 4Ω • Sine wave power per channel: 2x250W @ 4Ω (500 msec) • Dynamic bridged output power: 700W @ 8Ω • Bridged Sine wave output power: 500 W @ 8Ω (500 msec) • High ...

powered up. Full details of the available settings can be found

below. 6. Channel 2 speaker output on 2 pole euroblock connector. 7. Channel 1 speaker output on 2 pole euroblock connector. 8. Channel 2 speaker output on speakon connector. Pin 1+ = speaker 2 +, pin 1- = speaker 2 -. 9. Channel 1 and 2 stereo speaker outpu ...

DIGITAL POWER AMPLIFIER

1. Channel 2 overload led: when this led lights up, you are overloading the input. Lower the input signal immediately to prevent the amplifier from shutting down. 2. Channel 1 overload led: when this led lights up, you are overloading the input. Lower the input signal immediately to prevent the ampl ...

DIGITAL POWER AMPLIFIER

of your amplifier to drive a transformer to drive 100V speaker systems. This mode applies a highpass filter to channel 2. Filter characteristics: 12 dB/oct at 50 Hz. Butterworth characteristic. This setting increases amplifier stability when using a 100 volt transformer on output 1. • CH1 BRIDGED CH2: both amps are used in brid ...

DIGITAL POWER AMPLIFIER

Safety first! • Caution! This professional device needs to be installed by qualified personnel only. • Please check the carton box for any kind of damage on reception of the goods. In case of a damaged carton, please contact your dealer before opening the carton. • !!!! Danger !!!! Exposure to high sound levels may cause a permanent hearing loss. Individuals vary considerably to sound pressure level induced hearing loss b

Set level controls on amplifiers all the way down during power-

up to prevent speaker damage if there are high signal levels at the inputs. • Do not connect the inputs / outputs of amplifiers or consoles to any other voltage source, such as a battery, mains source, or power supply, regardless of whether the amplifier or console is turned on or off. • Power down & disconnect units from mains voltage before making c
DIGITAL POWER AMPLIFIER Features • 1 rack unit high • High power Hypex® class-D power amplifier modules • Bridgeable 2 channel amplifier • Dynamic output power: 2x350W @ 4Ω • Sine wave power per channel: 2x250W @ 4Ω (500 msec) • Dynamic bridged output power: 700W @ 8Ω • Bridged Sine wave output power: 500 W @ 8Ω (500 msec) • High thermal efficiency • Highest possible damping factor • Soft start switching power supply unit �

Unbalanced inputs on RCA with pass through

• Input level attenuators on all inputs • 4-pole Speakon® speaker output connectors • Euroblock speaker output connectors • Extended speaker and amp protection circuits: DC protect, over current protect, over temperature protect, input overload • Individual channel mute buttons and versatile LED status indicators • This unit has NOT been designed for use in mobil
DIGITAL POWER AMPLIFIER 1. Channel 2 overload led: when this led lights up, you are overloading the input. Lower the input signal immediately to prevent the amplifier from shutting down. 2. Channel 1 overload led: when this led lights up, you are overloading the input. Lower the input signal immediately to prevent the amplifier from shutting down. 3. Channel 2 input gain setting. Adjust the input gain to the output lev

powered up. Full details of the available settings can be found

below. 6. Channel 2 speaker output on 2 pole euroblock connector. 7. Channel 1 speaker output on 2 pole euroblock connector. 8. Channel 2 speaker output on speakon connector. Pin 1+ = speaker 2 +, pin 1- = speaker 2 -. 9. Channel 1 and 2 stereo speaker output on speakon connector. Pin 1+ = speaker 1 +, pin 1- = speaker 1 -; Pin 2+ = speaker 2+, pin 2- = s
DIGITAL POWER AMPLIFIER Operation 1. Removable rack ears for 19” rack mounting. 2. Power switch: after switching on the power, the power led will light up after approx 1 second. The limit-muted leds will light up for a few seconds to avoid excessive power on pop noise. 3. Power led 4. Channel 1 status led bar and mute switch: when the mute switch is pressed, the orange “LIMIT – MUTED” led will light up. This led will also light up when the

CH1 SUB – TOP CH2: frequencies below 100 Hz are sent to the

sub channel (CH1). Frequencies above 100 Hz are sent to the top channel (CH2).The Filter slope (12 dB/oct or second order Butterworth characteristic) and frequency (100Hz) are fixed. The Audio signal from input 1 is used. • CH1 TRAFO LOAD: Use this mode when you want channel 1 of your amplifier to drive a transformer to drive 100V speaker systems. This m
DIGITAL POWER AMPLIFIER of your amplifier to drive a transformer to drive 100V speaker systems. This mode applies a highpass filter to channel 2. Filter characteristics: 12 dB/oct at 50 Hz. Butterworth characteristic. This setting increases amplifier stability when using a 100 volt transformer on output 1. • CH1 BRIDGED CH2: both amps are used in bridge. Audio signal from input 1 is used. • Combination CH1 SUB – TOP CH2 with CH2 TRAFO LOAD: thi

!!! IMPORTANT !!!

This amplifier relies on convectional cooling only. In normal situations, overheating will not occur due to the class D amplifier topology. Since there are no cooling fans in the amplifier, make sure the convectional cooling system can work properly. The unit can be built in a 19 inch rack system, but it is forbidden to block the ventilation holes provided. Therefore, it is absolutely necessary to allow at
DIGITAL POWER AMPLIFIER 110 VAC operation: it is possible to operate the unit at 110 (115) VAC. Therefore, open the unit and set a wire jumper on the connector for 110 VAC operation.

Dynamic output power

2 x 350 W @ 4 Ω Sine wave power per channel 250 W @ 4 Ω (500 msec) Dynamic output power bridged 700 W @ 8 Ω Sine wave power bridged 500 W @ 8 Ω Minimum output load impedance CH1 and CH2 4 Ω Minimum output load impedance bridge mode 8 Ω Input connections 2 x balanced euroblock, 4 x unbalanced cinch with pass through Input sensitivity 0 dBV / 1 V Input impedance 22 k
DIGITAL POWER AMPLIFIER Cooling convectional Max power consumption 600 W Operating temperature range 0 to 40°C Mains operating voltage 230 VAC / 50 - 60 Hz (115VAC with internal jumper) Dimensions 483 x 44 x 235 mm ( including rack ears) Net weight 3.1 kg Gross weight 4.9 kg

Industriepark Brechtsebaan 8 bus 1

2900 Schoten - Belgium Company names, product names and trademarks are property of their respective owners. Apart-Audio specifications are subject to change without notice.

APART Amplifier Owners Instructions: