Honda 08E91-E22-101A Installation Instructions Manual

AII 13148-49239 (1302) 1 of 27 08E92-T0A-1A00-90 AII 13148-49239 REMOTE CONTROL ENGINE STARTER 2013 CR-V (EXCEPT LX) FEB 2013 PARTS LIST Remote Control Engine Starter Unit Kit P/N 08E91-E22-101A Transmitter Control unit Antenna Key ring Protective tape Fuse label Caution label Accessory User’s Information Manual Quick Start Guide Remote Control Engine Starter Attachment Kit P/N 08E92-T0A-100A Control unit bracket Engine starter harness 3 Relays 8 mm Nut 20 Wire ties ...

AII 13148-49239 (1302) © 2013 American Honda Motor Co., Inc. – All Rights Reserved. Long wire tie 7 Urethane tapes Template Clip TOOLS AND SUPPLIES REQUIRED Phillips screwdriver Diagonal cutters Ratchet 8 mm, 10 mm, and 12 mm Sockets Combination wrench Isopropyl alcohol Scissors Small flat-tip screwdriver Shop towel Ruler Tape measure HDS (Honda Diagnostic System) Needle nose pliers Masking tape Electrical tape The following tool is available through the Honda Tool and Equipment Program. On the iN click on: Service > Service Bay > Tool and Equipment Program, the enter the number under search. Or call 888-424-6857. Trim Tool Set (T/N SOJATP20 ...

AII 13148-49239 (1302) 3 of 27 Setting the Control Unit 3. Using a small flat-tip screwdriver, set the switches on the (accessory) control unit to the locations shown. NOTE: • The switches must be set before the control unit is plugged in. • If the switch settings are not correct, the remote engine starter will not operate correctly. • If setting the switches with the control unit installed in the vehicle, touch the metal part of the screwdriver to any metal part of the vehicle to discharge any static electricity. • If you change the switch settings with the unit connected, you mus ...

AII 13148-49239 (1302) © 2013 American Honda Motor Co., Inc. – All Rights Reserved. 6. Release the driver’s sunvisor and passenger’s sunvisor from the two sunvisor holders. Q0N2013AG Rotate. SUNVISOR HOLDER SUNVISOR HOLDER 2 SUNVISOR HOLDERS SUNVISOR 7. Rotate each sunvisor holders 45° counterclockwise to remove the two sunvisor holders. 8. Pull away the driver’s door opening seal from the driver’s A-pillar. Gently pull out the driver’s A-pillar trim to release the clips. Q0N2014AG VEHICLE PANEL CLIP 2 CLIPS DRIVER’S A-PILLAR TRIM DRIVER’S DOOR OPENING SEAL Pull away. CLIP DRIVER’S A-PILLAR 9. To prevent the clips from falli ...

AII 13148-49239 (1302) 5 of 27 11. Remove the remaining upper clip from the driver’s A-pillar. Q0N2017AG Push 2 tabs. UPPER CLIP Discard. DRIVER’S A-PILLAR 12. Temporarily reinstall the driver’s A-pillar trim, and check the overlap between the headliner and the driver’s A-pillar trim according to the service manual. Remove the driver’s A-pillar trim. Install the new clip (supplied) to the driver’s A-pillar trim. Q0N2018AG DRIVER’S A-PILLAR TRIM (inside) NEW CLIP 13. Remove the driver’s dashboard panel (six clips and unplug the vehicle connector). Q0N2019BG VEHICLE CONNECTOR ...

AII 13148-49239 (1302) © 2013 American Honda Motor Co., Inc. – All Rights Reserved. 15. Remove the driver’s dashboard under cover (turn the knob, one clip and one pin). Q0N2021BG PIN DRIVER’S DASHBOARD UNDER COVER KNOB Turn. CLIP 16. Remove the driver’s dashboard lower cover (eight clips and unplug the vehicle connector). Q0N2022AG VEHICLE CONNECTOR 8 CLIPS DRIVER’S DASHBOARD LOWER COVER 17. Attach the masking tape to the upper column cover as shown. Q0N2023AG MASKING TAPE UPPER COLUMN COVER STEERING WHEEL 18. Lower the tilt lever, and turn the steering wheel 90° counterclockwise. Q0N2024BG PLASTIC TRIM TOOL STEERING WHEEL LOCK UPPE ...

AII 13148-49239 (1302) 7 of 27 20. Turn the steering wheel 180° clockwise. Using a plastic trim tool, release the lock as shown. Q0N2025BG LOCK UPPER COLUMN COVER PLASTIC TRIM TOOL 21. Secure the upper column cover to the meter panel with the tape. Q0N2026AG TAPE 2 RETAINING TABS UPPER COLUMN COVER METER PANEL 22. Remove the two self-tapping screws from the lower column cover. Q0N2027AG LOWER COLUMN COVER SELF-TAPPING SCREWS 23. Remove the lower column cover (one self-tapping screw). Q0N2028AG SELF-TAPPING SCREW LOWER COLUMN COVER ...

AII 13148-49239 (1302) © 2013 American Honda Motor Co., Inc. – All Rights Reserved. 24. Remove the driver’s front door sill trim (two retaining tabs, three clips, and two hooks). Q0N2029BG 2 RETAINING TABS FRONT 3 CLIPS 2 HOOKS DRIVER’S FRONT DOOR SILL TRIM 25. Pull away the driver’s door opening seal, and remove the driver’s kick panel (two clips). Q0N2030AG DRIVER’S DOOR OPENING SEAL Pull away. DRIVER’S KICK PANEL 2 CLIPS Installing the Antenna 26. Using the two pairs of needle nose pliers, bend the antenna plate according to the full scale drawing as shown. Q0N1708CG ANTENNA ANTENNA ANTENNA PLATE NEEDLE NOSE PLIERS ANTENNA PLA ...

AII 13148-49239 (1302) 9 of 27 27. Using scissors, cut out the template. Q0N1701BG Cut out. TEMPLATE SCISSORS 28. Using the strips of masking tape, attach the template to the front windshield. Align the template with the black ceramic paint as shown. Q0N1702CG TEMPLATE MASKING TAPES Align this end with the end of the black ceramic paint. TEMPLATE BLACK CERAMIC PAINT FRONT WINDSHIELD CORRECT 29. Starting from the antenna end of the antenna cable, wrap three urethane tapes to the antenna cable at the measurements shown. Q0N1703AG ANTENNA URETHANE TAPES 20 mm (0.8 in.) 410 mm (16.1 in.) ANTEN ...

AII 13148-49239 (1302) © 2013 American Honda Motor Co., Inc. – All Rights Reserved. 33. Gently pull down the headliner, and tuck the antenna cable under the headliner. Be careful not to crease the headliner. Q0N1705AG ANTENNA CABLE HEADLINER HEADLINER VEHICLE PANEL ANTENNA CABLE 34. Using isopropyl alcohol on a shop towel, thoroughly clean the vehicle panel, where the urethane tapes will attach. Q0N1706AG VEHICLE PANEL Clean with isopropyl alcohol. ANTENNA CABLE 2 URETHANE TAPES URETHANE TAPE Cut in half. 35. Using scissors, cut one urethane tape in half. Secure the antenna cable to the vehicle panel with two cut pieces of urethane tape. Be ...

AII 13148-49239 (1302) 11 of 27 Routing the Engine Starter Harness 39. Plug the three relays into the relay block on the engine starter harness. Q0N1801AG 40A FUSE LABEL RELAYS RELAY 40A FUSE LABEL FUSE BLOCK RELAY BLOCK ENGINE STARTER HARNESS 3A FUSE LABEL 40. Using isopropyl alcohol on a shop towel, thoroughly clean the relay block and fuse block where the 3A fuse label and 40A fuse labels will attach. 41. Attach the 3A fuse label and two 40A fuse labels to the relay block and fuse block on the engine starter harness. 42. Route the two 28-pin connectors of the engine starter harness upwa ...

AII 13148-49239 (1302) © 2013 American Honda Motor Co., Inc. – All Rights Reserved. 47. Secure the engine starter harness and the antenna cable to the vehicle frame with one wire tie. Q0N1806BG VEHICLE HARNESS WIRE TIE ENGINE STARTER HARNESS WIRE TIE ENGINE STARTER HARNESS VEHICLE FRAME ANTENNA CABLE ANTENNA CABLE 48. Secure the engine starter harness and the antenna cable to the vehicle harness with one wire tie. 49. Unplug the vehicle 5-pin connector from the fuse box, and plug it into the engine starter harness 5-pin connector. Q0N1807BG FRONT VIEW VEHICLE 5-PIN CONNECTOR ENGINE STARTER HARNESS 5-PIN CONNECTOR FUSE BOX FUSE BOX Plug in h ...

AII 13148-49239 (1302) 13 of 27 51. Attach the connector clip from the engine starter harness 5-pin connector to the hole in the vehicle panel. Q0N1901BG ENGINE STARTER HARNESS 5-PIN CONNECTOR FUSE BOX VEHICLE PANEL HOLE CONNECTOR CLIP 52. Slide the other clip on the engine starter harness onto the vehicle connector. Note the direction and the orientation of the clip. Q0N1902BG ENGINE STARTER HARNESS CLIP VEHICLE CONNECTOR FRONT If the vehicle is equipped with the accessory fog lights, go to step 54; otherwise, continue with step 53. 53. Plug the engine starter harness 4-pin connector into ...

AII 13148-49239 (1302) © 2013 American Honda Motor Co., Inc. – All Rights Reserved. 54. Unplug the fog light 4-pin connector from the fuse box, and plug it into the engine starter harness 4-pin connector. Q0N1904BG FRONT VIEW FUSE BOX FUSE BOX Plug in here. ENGINE STARTER HARNESS 4-PIN CONNECTOR FOG LIGHTS 4-PIN CONNECTOR ENGINE STARTER HARNESS 4-PIN CONNECTOR 55. Plug the remaining engine starter harness 4-pin connector into the fuse box. 56. Unplug the vehicle 38-pin connector from the fuse box as shown. Q0N1905AG VEHICLE 38-PIN CONNECTOR FUSE BOX FRONT VIEW VEHICLE 38-PIN CONNECTOR CONNECTOR COVER 57. Remove the connector cover. 58. Remo ...

AII 13148-49239 (1302) 15 of 27 60. Release the retainer from the 8-pin connector. Q0D1604AK HARNESS SIDE VIEW ORANGE WIRE ENGINE STARTER HARNESS TERMINAL RETAINER 8-PIN CONNECTOR ORANGE WIRE 61. Insert the engine starter harness terminal (orange wire) into the 8-pin connector. Reinstall the 8-pin connector and lever. 62. Secure the engine starter harness to the vehicle harness with an electrical tape. Q0N1907AG VEHICLE HARNESS ENGINE STARTER HARNESS ELECTRICAL TAPE 63. Reinstall the connector cover. 64. Plug the vehicle 38-pin connector into the fuse box. 65. Unplug the vehicle 24-pin con ...

AII 13148-49239 (1302) © 2013 American Honda Motor Co., Inc. – All Rights Reserved. 66. Slide the clip from the engine starter harness 24-pin connector onto the bottom of the fuse box, then plug the remaining vehicle 24-pin connector into the engine starter harness 24-pin connector. Q0N2002BG FRONT VIEW FUSE BOX FUSE BOX ENGINE STARTER HARNESS 24-PIN CONNECTOR VEHICLE 24-PIN CONNECTOR FUSE BOX ENGINE STARTER HARNESS 24-PIN CONNECTOR 67. Secure the engine starter harness to the vehicle harness with two wire ties. Q0N2003BG FUSE BOX ENGINE STARTER HARNESS VEHICLE HARNESS WIRE TIES 68. Route the engine starter harness under the dashboard and t ...

AII 13148-49239 (1302) 17 of 27 70. Locate the white tape on the engine starter harness, and loosely secure the engine starter harness to the dashboard with one wire tie at the white tape. Q0N2005AG ENGINE STARTER HARNESS WIRE TIE Loosely secure. DASHBOARD WHITE TAPE 71. Route the engine starter harness up steering wheel as shown. Q0N2006BG ENGINE STARTER HARNESS VEHICLE CLIP WHITE TAPE FRONT VIEWED FROM BOTTOM 2 WIRE TIES VEHICLE HARNESS 72. Align the white tape on the engine starter harness with the vehicle clip, and secure the engine starter harness to the vehicle harness with two wire ...

AII 13148-49239 (1302) © 2013 American Honda Motor Co., Inc. – All Rights Reserved. 76. Route the engine starter harness across the steering column area as shown. Q0N2008AG VEHICLE 10-PIN CONNECTOR ENGINE STARTER HARNESS ENGINE STARTER HARNESS 10-PIN CONNECTOR STEERING WHEEL WIPER SWITCH ENGINE STARTER HARNESS 10-PIN CONNECTOR 77. Unplug the vehicle 10-pin connector from the wiper switch, and plug it into the engine starter harness 10-pin connector. 78. Plug the remaining engine starter harness 10-pin connector into the wiper switch. 79. Secure the 10-pin connectors and engine starter harness to the vehicle harness with one wire tie. Q09030 ...

AII 13148-49239 (1302) 19 of 27 80. Unplug the vehicle 12-pin connector from the combination light switch, and plug it into the engine starter harness 12-pin connector. QA20704BG VEHICLE 12-PIN CONNECTOR ENGINE STARTER HARNESS 12-PIN CONNECTOR STEERING WHEEL COMBINATION LIGHT SWITCH ENGINE STARTER HARNESS 12-PIN CONNECTOR 81. Plug the remaining engine starter harness 12-pin connector into the combination light switch. 82. Secure the engine starter harness to the vehicle harness with two wire ties. Check that the harness is secured without undue strain to the both left and right connector c ...

AII 13148-49239 (1302) © 2013 American Honda Motor Co., Inc. – All Rights Reserved. 83. Route the antenna cable along the engine starter harness as shown. Q0N2303AG ENGINE STARTER HARNESS FRONT LEFT KNEE BOLSTER WIRE TIE ANTENNA CABLE WIRE TIE ANTENNA CABLE WIRE TIE VEHICLE HARNESS DASHBOARD FUSE BOX 84. Secure the antenna cable to the engine starter harness with two wire ties. 85. Loosely secure the antenna cable to the dashboard with one wire tie loosely installed in step 70. Installing the Control Unit 86. Using isopropyl alcohol on a shop towel, clean the area where the urethane tape will attach. Q0N2305AG URETHANE TAPE VEHICLE UNIT Cle ...