Oncam EVO-180-WID Installation & User Manual
Read Online
Read the Oncam EVO-180-WID Installation & User Manual online using the built-in PDF viewer.
Key Pages of Document
Installation & User Manual © Oncam Global Group AG, 2013 - 2018. All rights reserved. EVO-180-W#D-06, Rev A February 2018 ...
February 2018 © Oncam Global Group AG, 2013 - 2018. All rights reserved. 2 Manual Copyright © Oncam Global Group AG, 2013 - 2018. All rights reserved. No part of this manual may be reproduced except for your express personal use. Oncam and their affiliate’s further reserve the right to alter, amend or revise this document and any product specifications without any obligation to provide not ...
February 2018 © Oncam Global Group AG, 2013 - 2018. All rights reserved. 3 Contents 1 Overview ...............................................................................................................................................................................................5 1.1 Panoramic View ........................................................................................ ...
February 2018 © Oncam Global Group AG, 2013 - 2018. All rights reserved. 4 11 Copyright and Legal Notices ...............................................................................................................................................................41 12 Additional Online Resources ................................................................................................ ...
February 2018 © Oncam Global Group AG, 2013 - 2018. All rights reserved. 5 1 Overview The Oncam Evolution 180 IP Series cameras are innovative and use a fisheye lens to create a 180° view with an extremely large area of coverage. The Oncam 180° IP camera may replace two or more conventional fixed cameras for seamless wall-mounted coverage of an entire scene with no gaps or blind spots. The ...
February 2018 © Oncam Global Group AG, 2013 - 2018. All rights reserved. 6 CAUTION: Do not use an excess of 15 VDC from an external power supply. Doing so may damage the camera and void the warranty. CAUTION: Do not power the camera using 12 V and PoE at the same time. Doing so may damage the camera and void the warranty. 1.6 Audio Input The camera mic input is provided from the 12-pin I/O co ...
February 2018 © Oncam Global Group AG, 2013 - 2018. All rights reserved. 7 2.1 Camera Mounting Accessories The three mounting boxes supplied with the Indoor camera allow for a wide variety of installation environments. Each of them may be surface-mounted, for example to a wall or ceiling, or screwed directly onto the bottom of a threaded pendant conduit. The conduit ports are threaded with ...
February 2018 © Oncam Global Group AG, 2013 - 2018. All rights reserved. 8 2.1.3 45° Mounting Box The 45° Mounting Box can be mounted on the ceiling or wall and is useful in long, narrow scenes like corridors, where having a degree of side view is beneficial. As with the 25° Mounting Box, Oncam’s Angle Correction Technology can be used to straighten-out distortion caused by tilting the ...
February 2018 © Oncam Global Group AG, 2013 - 2018. All rights reserved. 9 3 I/O Connector Access I/O ports and the SD card slot by removing the cover on the rear of the camera. The 12-pin I/O connector under the rear cover provides all user I/O and power connections. The green, labelled tool-less mating half for this 12-pin I/O connector is supplied with the camera. The other green two-pin s ...
February 2018 © Oncam Global Group AG, 2013 - 2018. All rights reserved. 10 3.1 RJ45 Ethernet Socket Two loops are provided for cable ties in the rear structure of the camera body. These may be used to secure the cables for extra security and strain relief on their connectors. CAUTION: Do not use an excess of 15 VDC from an external power supply. Doing so may damage the camera and void the w ...
February 2018 © Oncam Global Group AG, 2013 - 2018. All rights reserved. 11 3.2.3 External IR Filter Control In External control of the camera’s Day/Night mode and IR Cut Filter is provided from ALM_IN_2 input of the camera’s 12-pin I/O connector, found under the cover on the back of the camera module. 3.3 Audio in/out (Microphone, Speaker) MIC or SPEAK relays sound in real-time over the ...
February 2018 © Oncam Global Group AG, 2013 - 2018. All rights reserved. 12 4 Camera Preparation and Installation For installation of your Oncam Evolution 180 camera, provided are the following instructions. Reference the Camera Web Interface, page 23 for more detailed features and functionality. 4.1 Parts Supplied • Camera Module • Quick Start Guide • 0° Mounting Box • Drilling Temp ...
February 2018 © Oncam Global Group AG, 2013 - 2018. All rights reserved. 13 4.2.3 Surface Mounting Box - 0° 1. Remove the two side screws holding the camera cover in place. 2. Separate the camera cover exposing the main camera module. 4.2.4 Surface Mounting Boxes - 25° and 45° 1. Remove the conduit plug from the bracket. 2. Remove the back cover from the bracket by sliding the cover away. ...
February 2018 © Oncam Global Group AG, 2013 - 2018. All rights reserved. 14 4.2.5 Pendant Mounting Box Remove the conduit plug from the bracket. 4.3 Surface - 0° Mounting Box The Evolution 180 Indoor Camera is intended for mounting on flat surfaces such as walls and ceilings. The camera is supplied with three different mounting boxes, angled at 0°, 25° and 45°. These allow the installer ...
February 2018 © Oncam Global Group AG, 2013 - 2018. All rights reserved. 15 4. Ensure the camera’s arrow is pointing up. 5. Connect the network cable to the camera module rear. Tie the cable to the camera body using the slots. Ensure the cable is routed inside the mounting box. 6. Attach the camera module to the bracket and secure with the four screws (provided). ...
February 2018 © Oncam Global Group AG, 2013 - 2018. All rights reserved. 16 7. Replace the camera cover with the two captive security screws. For mounting options, see Camera Mount, page 7. 4.4 Surface - 25° & 45° Mounting Box 1. Using the drilling template, drill mounting holes. 2. Mount the wall bracket onto the installation surface using appropriate screws for the surface type. Route the ...
February 2018 © Oncam Global Group AG, 2013 - 2018. All rights reserved. 17 4. Connect the network cable to the camera rear. 5. Attach the camera module to the bracket, securing it with the four screws (provided). ...
February 2018 © Oncam Global Group AG, 2013 - 2018. All rights reserved. 18 6. Replace the camera cover, securing it with the two side screws (provided). 4.5 Pendant Mounting Box 4.5.1 Installation Steps 1. Pass unterminated cable through the pendant mount and M20 conduit adapter. 2. Connect the mounting box to the pendant adapter and terminate the network cable. 3. Ensure the camera’s arro ...
February 2018 © Oncam Global Group AG, 2013 - 2018. All rights reserved. 19 4. Connect the network cable to the camera module rear. 5. Attach the camera module to the mounting box and secure with four screws (provided). 6. Replace the camera cover with the two side screws. ...
February 2018 © Oncam Global Group AG, 2013 - 2018. All rights reserved. 20 5 Lens Handling and Cleaning Do not remove the blue lens protection sticker until the camera is installed and ready for use. Clean the lens only when necessary. You should only handle the lens in a clean, low-dust environment while wearing powder-free acetone-impenetrable gloves. Since oil, dust and debris from your h ...
