jablotron JA-63 „PROFI“ Operation & User’s Manual

- 2 - MGK51504 Contents: 1 Limited warranty ........................................................................................................................... 2 2 Indicators....................................................................................................................................... 3 3 Controlling the system .................................................................................... ...

- 3 - MGK51504 Note: features of this system can be substantially modified by programming during installation. The installer should instruct the users how to operate and test the system. 2 Indicators The alarm system’s status is indicated on the keypad. There can be multiple keypads in the system and in such a case all keypads will have identical functions. A keypad’s LED indicators and display inform the user about the c ...

- 4 - MGK51504 Telephone line indicated event (Tamper or Failure) was caused by the telephone line digital bus indicated event (Tamper or Failure) was caused by a device (keypad or PC) connected to the digital bus communication failure wireless keypad lost connection with the control panel error self testing error – call installer tab. 1 88 display specifies mode of the control panel: user mode authorized supervisor can tes ...

- 5 - MGK51504 Master code Is an extra (15th) access code for the supervisor. It can operate the system and it also allows for the programming of the other user codes and to enter the user mode (see section 4). Factory default master code is 1234. The supervisor should change it after installation. Service code Is an extra code, used by the installer to enter the programming mode. End users are not usually told this code. If ...

- 6 - MGK51504 3.2 Disarming On the keypad - enter your user code On the remote control (RC-4x) – press the button  system will beep twice  if there are 3 beeps, important information is indicated and will be displayed on the keypad. Examples: o FAILURE LED is flashing – press the N key to view the cause o ALARM LED and zone number is flashing = alarm in the memory. Be careful and check the house.  if you enter ...

- 7 - MGK51504 3.5 Home arming The installer can program particular detectors so that they will be automatically bypassed in the so called “Home” partial arming. This allows for people to stay in the particular part of the house after arming. To arm partially:  On the keypad press home arming button H will indicate the Home partial arming on the keypad. To disarm a partially armed system - enter your user code or press ...

- 8 - MGK51504 3.9 Subsystem arming In a large building a sub control panel can be enrolled to the JA-63. The subsystem reports all alarms and failures to the main system. The installer can program if the systems will be armed and disarmed separately (by their own codes and remote controls) or if the main control panel will rule the sub control panel. Ask your installer for explanation on how to operate your system if a sub c ...

- 9 - MGK51504 4.2 User codes setting There can be up to 14 different user codes for individual users. The system stores to its memory which code was used for what event and when. This data can go to a Central monitoring station as well and can also be viewed by a PC with Comlink software. All user codes are empty as a factory default and the supervisor should program them entering: F 6 xxxx yy zzzz where xxxx ...

- 10 - MGK51504 Actions' table a no splitting split 0 no action no action 1 arm all arm all 2 disarm disarm all 3 partial arming arm A 4 partial arming arm B 5 disarm disarm A 6 disarm disarm B 4.4 Automatic arming / disarming The system can automatically arm and disarm for a requested period of a day. While in the user more, up to ten instructions (time & action) can be programmed in the period of one day. To switch the cont ...

- 11 - MGK51504 c. multiple pressing and holding of the keys (2 or 3) will switch the bypass on – off – on – off … 4. By repeating step 3. you can bypass all required alarm sources.  To close the Bypass menu press the N key. If anything is bypassed when arming, four beeps will sound and b will be displayed on the keypad during the exit delay (and partial arming will be recorded to the memory).  All bypasses sele ...

- 12 - MGK51504 Example: to store tel. number 0 123456 to memory no. 2 enter: 7 0 F0 12345 F2 To delete a telephone number enter: 7 F0 Fy where y is a memory number from 1 to 4 To exit user mode, press the N key. 5.2.2 Telephone communicator testing Testing is possible in the user mode. To switch the control panel to the user mode enter F 0 master code. User mode will be indicated by a U on the keypad. Entering 89 will cause ...

- 13 - MGK51504  open the cover of the detector (keypad)  replace its batteries with new ones (use only corresponding size and good quality alkaline batteries). Wait for approximately 20 seconds before inserting batteries  close the device’s cover and test its function.  to exit User mode, press the N key on the keypad Note: normal battery life in wireless items is about 1 year. Exposure to a very cold temperatu ...

- 14 - MGK51504 User codes and controllers code index user name section notes A B 0. Master code - supervisor 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. 12. 13. 14. c1 c2 c3 c4 c5 c6 c7 c8 Telephone communicator setting memory calling to tel. number notes 1. 2. 3. 4. 5. Pager Timers exit delay sec entrance delay sec alarm duraton min Notes: ...

- 15 - MGK51504 Detectors position location in the house detectors type reaction* section A B S WIRELESS DETECTORS 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. 12. 13. 14. 15. 16. WIRED INPUTS 1. 2. 3. 4. * I – instant D – delayed F – fire P – panic T – tamper N – next delayed ...