Honda 08E91-E22-101A Installation Instructions Manual

AII 41964 (0911) 1 of 23 08E92-TP6-1000-91 AII 41964 REMOTE CONTROL ENGINE STARTER 2010 ACCORD CROSSTOUR NOV 2009 PARTS LIST Remote Engine Starter Unit Kit P/N 08E91-E22-101A Transmitter Control unit Antenna Key ring Protective tape Caution label Fuse label Accessory User’s Information Manual Quick start guide Remote Control Engine Starter Attachment Kit P/N 08E92-TA0-101 Engine starter harness Control unit bracket Template 3 Relays Ground bolt Flange nut ...

AII 41964 (0911) © 2009 American Honda Motor Co., Inc. – All Rights Reserved. 20 Wire ties 2 Long wire ties 8 Urethane tapes A-Pillar clip TOOLS AND SUPPLIES REQUIRED Flat-tip screwdriver Phillips screwdriver Small flat-tip screwdriver Ratchet 10 mm Socket 10 mm Combination wrench Isopropyl alcohol Shop towel Tape measure Clip remover Scissors Small rubber mallet Honda Diagnostic System (HDS) Masking tape 2 Pairs of needle nose pliers Diagonal cutters Utility knife Plastic Trim Tool (T/N SILTRIMTL10) Illustration of the Remote Control Engine Starter Installed on the Vehicle INSTALLATION 1. Make sure you have the anti-theft codes for the audi ...

AII 41964 (0911) 3 of 23 Setting the Control Unit 3. Using a small flat-tip screwdriver, adjust the switches on the (accessory) control unit to the locations shown. NOTE: • The switches must be adjusted before the control unit is plugged in. • If the switch settings are not correct, the remote engine starter will not operate correctly. • If adjusting the switches with the control unit installed in the vehicle, touch the metal part of the screwdriver to any metal part of the vehicle to discharge any static electricity. • If you change the switch settings with the unit connected, you ...

AII 41964 (0911) © 2009 American Honda Motor Co., Inc. – All Rights Reserved. 6. Open the sunglass holder. Remove the four screws (two black and two silver) and let the roof console drop down. Unplug the vehicle connectors and remove the roof console. 7. Turn the sunvisor holder 45° and remove the two sunvisor holders. 730202AB 2 BLACK SCREWS ROOF CONSOLE SUNGLASS HOLDER (Open.) VEHICLE CONNECTORS 2 SILVER SCREWS 6D1806BY SUNVISOR HOLDER Turn. SUNVISOR HOLDER 8. Pull away the door seal from the left A-pillar trim. 9. Using a small rubber mallet and a shop towel, gently tap the left A-pillar trim at the position shown to release the clip. 10 ...

AII 41964 (0911) 5 of 23 11. Remove and discard the clip from the left A-pillar trim, and install a new A-pillar clip (supplied) onto the left A-pillar trim. 12. Remove the driver’s dashboard lower cover (eight clips, two hooks, and vehicle connector). 6D18080Y CLIP (Discard.) LEFT A-PILLAR TRIM NEW A-PILLAR CLIP 6D1803AY 8 CLIPS DRIVER’S DASHBOARD LOWER COVER 2 HOOKS VEHICLE CONNECTOR 13. Remove the driver’s dashboard under cover (three clips and one pin). 14. Raise the front side of the left front door sill trim, and remove the left front door sill trim (four clips and one retainin ...

AII 41964 (0911) © 2009 American Honda Motor Co., Inc. – All Rights Reserved. 15. Pull away the door seal, and remove the left kick panel (two clips). 16. Pull away the door seal, and remove the driver’s dashboard side lid (three clips, four tabs, and three hooks). 932503AS 2 CLIPS DOOR SEAL LEFT KICK PANEL 6D1805BY DRIVER’S DASHBOARD SIDE LID 3 CLIPS 3 HOOKS DOOR SEAL 4 TABS 17. Lower the tilt lever and pull the steering wheel out. 18. Remove the upper steering column cover: • Insert a flat-tip screwdriver along the column guide inside the lower steering column cover, and gently pry out the retaining tab of the upper steering column c ...

AII 41964 (0911) 7 of 23 19. Remove the lower steering column cover (three screws). The upper screws are self-tapping screws. 20. If equipped, remove the vehicle unit (two bolts and vehicle 28-pin connector). 7111090Y LOWER STEERING COLUMN COVER SELF-TAPPING SCREW SCREW 732903BY BOLT VEHICLE 28-PIN CONNECTOR VEHICLE UNIT (If equipped) BOLT 21. Remove the bolt, and remove the vehicle unit from the vehicle bracket. Routing the Engine Starter Harness 22. Using isopropyl alcohol on a shop towel, clean the areas where the fuse labels will attach. 23. Attach the two 40A fuse labels to the engine ...

AII 41964 (0911) © 2009 American Honda Motor Co., Inc. – All Rights Reserved. 25. Install the three relays to the engine starter relay blocks. 26. Route the 12-pin/8-pin/5-pin connector end of the engine starter harness over the vehicle bracket towards the center of the vehicle. 6D1802BY ENGINE STARTER HARNESS RELAY BLOCKS 3 RELAYS 932520AS ENGINE STARTER HARNESS 12-PIN/8-PIN/5-PIN CONNECTOR STEERING SHAFT VEHICLE BRACKET 27. Route the 12-pin/8-pin/5-pin connector end of the engine starter harness to the ignition switch. 28. Unplug the vehicle 5-pin connector from the ignition switch, and plug the engine starter harness 5-pin connector into ...

AII 41964 (0911) 9 of 23 29. Wrap one urethane tape around the vehicle 5-pin connector, and tuck it into the area shown. 30. Unplug the vehicle 12-pin connector and plug it into the engine starter harness 12-pin connector. Plug the remaining engine starter harness 12-pin connector into the combination light switch. 6D1813AY URETHANE TAPE VEHICLE 5-PIN CONNECTOR VEHICLE 5-PIN CONNECTOR VEHICLE BRACKET Push. Push. Locked connector 1 2 6D18141Y 12-PIN CONNECTORS VEHICLE 12-PIN CONNECTOR ENGINE STARTER HARNESS COMBINATION LIGHT SWITCH 31. Unplug the vehicle 8-pin connector and plug it into the ...

AII 41964 (0911) © 2009 American Honda Motor Co., Inc. – All Rights Reserved. 33. Using two wire ties, secure the engine starter harness to the vehicle harness in the areas shown. 34. Unplug the vehicle 20-pin connector from the vehicle unit removed in step 21, and plug it into the engine starter harness 20-pin connector. Plug the remaining engine starter harness 20-pin connector into the vehicle unit. 6D1817BY VEHICLE HARNESS VEHICLE CLIP ENGINE STARTER HARNESS WIRE TIE WIRE TIE VEHICLE HARNESS ENGINE STARTER HARNESS Inside. 932504AS VEHICLE 20-PIN CONNECTOR 20-PIN CONNECTOR VEHICLE UNIT VEHICLE 20-PIN CONNECTOR 20-PIN CONNECTOR ENGINE ST ...

AII 41964 (0911) 11 of 23 38. Reinstall the vehicle unit to the vehicle bracket using the bolt removed in step 21. 39. Route the engine starter harness along the vehicle harness to the front of the fuse box. 40. Using one wire tie, loosely secure the engine starter harness to the vehicle harness. 932519AS VEHICLE BRACKET VEHICLE UNIT BOLT (removed in step 21) 6D1820AY WIRE TIE (Loosely secure.) FUSE BOX ENGINE STARTER HARNESS VEHICLE HARNESS 41. Unplug the vehicle 5-pin connector from the fuse box. Plug the engine starter harness 5-pin connector into the fuse box 5-pin connector. Wrap one ...

AII 41964 (0911) © 2009 American Honda Motor Co., Inc. – All Rights Reserved. 42. Plug the engine starter harness 12-pin connector into the fuse box 12-pin connector. NOTE: If another accessory 12-pin connector is already plugged into the fuse box: Unplug the 12-pin connector from the fuse box, then plug the engine starter harness 12-pin connector into the fuse box. Remove and discard the dummy connector from the engine starter harness, and plug the other accessory 12-pin connector into the engine starter harness 12-pin connector. 6D1821BY FUSE BOX 12-PIN CONNECTOR FUSE BOX ENGINE STARTER HARNESS 12-PIN CONNECTOR 6D1822BY FUSE BOX 12-PIN CO ...

AII 41964 (0911) 13 of 23 45. Attach the engine starter harness 20-pin connector to the vehicle connector as shown. 46. Remove and discard the hood opener bolt. Install the ground bolt with the engine starter harness ground terminal attached. 932506AS HOOD OPENER VEHICLE CONNECTOR ENGINE STARTER HARNESS 20-PIN CONNECTOR ENGINE STARTER HARNESS 20-PIN CONNECTOR 932507BS BOLT (Discard.) HOOD OPENER VEHICLE PANEL GROUND BOLT ENGINE STARTER HARNESS GROUND TERMINAL 47. Using one wire tie, secure the engine starter harness to the vehicle harness. 48. Using two wire ties, loosely secure the engine ...

AII 41964 (0911) © 2009 American Honda Motor Co., Inc. – All Rights Reserved. Installing the Antenna 49. Using scissors, cut out the appropriate template. 932509BS TEMPLATE (Cut out.) 50. Using scissors, trim the template. EX model: EX–L model: 932510AS TEMPLATE Cut out. Cut out. 932511AS TEMPLATE Cut out. ...

AII 41964 (0911) 15 of 23 51. Attach the template to the windshield. EX model: EX–L model: 932513AS TEMPLATE CENTER BLACK CERAMIC WINDSHIELD BLACK CERAMIC OF MIRROR BASE MASKING TAPES 932514AS TEMPLATE CENTER WINDSHIELD BLACK CERAMIC MASKING TAPES 52. Using two pair of needle nose pliers, bend the antenna plate according to the full scale drawing shown. 721509BY ANTENNA PLATE 10 mm (0.4 in.) SCALE 2 PAIRS OF NEEDLE NOSE PLIERS 10 mm (0.4 in.) ...

AII 41964 (0911) © 2009 American Honda Motor Co., Inc. – All Rights Reserved. 55. Using isopropyl alcohol on a shop towel, clean the area where the antenna will attach. 56. Remove the backing from the antenna. Insert the antenna plate over the headliner, and attach the antenna to the windshield aligning it with the template. Press the antenna firmly. NOTE: This antenna should only be installed if the ambient air temperature is 15°C (60°F) or above. 57. Remove the template. 58. Gently pull down the headliner, and tuck the antenna cable under the headliner. Be careful not to crease the headliner. 721510AY TEMPLATE HEADLINER ANTENNA Press fi ...

AII 41964 (0911) 17 of 23 59. Using isopropyl alcohol on a shop towel, clean the areas where the urethane tapes will attach. 60. Cut one urethane tape in half. Secure the antenna cable to the vehicle panel using the cut pieces of urethane tape. 61. Route the antenna cable down and under the dashboard through the A-pillar trim opening. 932515AS ANTENNA CABLE VEHICLE PANEL (Clean with isopropyl alcohol.) Cut in half. URETHANE TAPE VEHICLE HARNESS 932523AS ANTENNA CABLE A-PILLAR TRIM OPENING 62. Using four wire ties, secure the antenna cable to the vehicle harness. 63. Using one wire tie, sec ...

AII 41964 (0911) © 2009 American Honda Motor Co., Inc. – All Rights Reserved. 65. Route the antenna cable along the engine starter harness as shown. 66. Secure the antenna cable using the three loosely secured wire ties. Installation of the Control Unit 67. Install the control unit bracket to the control unit. 6D1845BY ANTENNA CABLE ENGINE STARTER HARNESS VEHICLE HARNESS LOOSELY SECURED WIRE TIE (Secure.) LOOSELY SECURED WIRE TIE (Do not secure yet.) 6D18461Y CONTROL UNIT BRACKET CONTROL UNIT 68. Plug the engine starter harness 28-pin connector into the control unit. 69. Install the clip on the engine starter harness to the control unit bra ...

AII 41964 (0911) 19 of 23 71. Secure the control unit to the vehicle frame using the flange nut. 72. Wrap one urethane tape around the vehicle connector. 932524AS VEHICLE FRAME FLANGE NUT CONTROL UNIT 932516AS VEHICLE CONNECTOR URETHANE TAPE 73. Attach the engine starter harness relay block clip to the vehicle frame. 74. Bundle up the excess antenna cable and secure it to the engine starter harness and the vehicle harness using the loosely secured wire tie. 75. Using two wire ties, secure the antenna cable to the engine starter harness. 6D1860AY ENGINE STARTER RELAY BLOCK ENGINE STARTER HA ...

AII 41964 (0911) © 2009 American Honda Motor Co., Inc. – All Rights Reserved. 76. Under the hood, locate the area where the caution label will attach. Using isopropyl alcohol on a shop towel, clean the hood where the caution label will attach. 77. Attach the caution label to the hood in the area shown. 78. Reinstall all removed parts. Check that all clips and other fasteners are installed securely. Take care not to pinch the airbag with the clip during reinstallation of the A-pillar trim. Do not push the A-pillar trim excessively. 79. Reconnect the negative cable to the battery. 80. Enter the customer’s radio anti-theft code, and reset th ...