Arcam A90 Handbook

Text of Arcam A90 Handbook

Arcam A90, P90 and P90/3 amplifiers

Amplificateurs Arcam A90, P90 et P90/3 Arcam-Verstärker A90, P90 und P90/3 Arcam-versterkers A90, P90 en P90/3 Nederlands

CAUTION: To reduce the risk of electric shock, do not

remove cover (or back). No user serviceable parts inside. Refer servicing to qualified service personnel. WARNING: To reduce the risk of fire or electric shock, do not expose this apparatus to rain or moisture. The lightning flash with an arrowhead symbol within an equilateral triangle, is intended to alert the user to the presence of uninsulated ‘dangerous voltage’ withi

Using this handbook

This handbook has been designed to give you all the information you need to install, connect, set up and use the Arcam A90 integrated amplifier or the P90 power amplifier. The A90 amplifier is described first, then the P90. The CR-389 remote control handset supplied with the A90 integrated amplifier is also described. Your amplifier(s) may have been installed and set up by an authorised Arcam dealer. In this case, you

Installation: A90 integrated amplifier

Positioning the unit Place your amplifier on a level, firm surface. Avoid placing the unit in direct sunlight or near sources of heat or damp. Ensure adequate ventilation. Do not place the unit in an enclosed space such as a bookcase or cabinet as both of these will impede air flow through the ventilation slots. Connecting to loudspeakers The red and black terminals on the back of the amplifiers 4 are used t

Arcam A90 For remote standby operation, the amplifier’s control power

supply is kept powered up all the time the unit is connected to the mains supply. The front panel power switch powers down all other circuitry. Power consumption in this mode is less than 2W. This means that even though the power switch is off, it may be possible to hear a slight residual hum coming from the mains transformer inside the amplifier. This is perfectl

Using your A90 integrated amplifier

Front panel controls This section describes how to operate your amplifier. If your amplifier has not been installed for you, you should first read the section ‘Installation: A90 integrated amplifier’ on page 4. POWER (and power indicator light) 8 Switches the unit on and off. (You can also switch the amplifier into standby mode with the remote control handset.) The light indicates the status of the amplifie

With the Arcam A90 it is possible to listen to and record from

one source, or to listen to one source while recording another. Both sets of tape sockets are identical in sensitivity and suitable for use with almost any type of recorder (cassette, CDR, MD, VCR, reel-to-reel, etc.). The record signal is sent to both the TAPE and VCR output sockets. RECORD bk To record the currently selected source, press RECORD until the display s

Setting up your A90 integrated amplifier

choose setting adjust BALANCE adjust BASS adjust TREBLE adjust LEFT RIGHT –dB +dB –dB +dB Customize -> DOWN UP edit STANDARD FINE REFERENCE continue Volume Resolution GRAPHIC/ NUMERIC edit GLOBAL/ PER SOURCE continue edit ARCAM Amp continue edit AUX/ PHONO continue edit NO/YES RESTORE SETTINGS PHONO/AUX TEXT WELCOME MESSAGE TONE CONTROL edit continue edit continue TRIM VOLUME DISPLAY INPUT TRIMS Welcom

Using the remote control

CR-389 Remote Control The CR-389 remote control gives access to all functions available on the front panel of the A90. It also has controls to operate Arcam CD players, AM/FM tuners and DAB tuners. The remote control transmits Philips RC-5 type codes. Source selection buttons These operate in the same way as the source selectors on the front panel of your integrated amplifier. Volume and (mute) Press + to increas

Connecting to power, loudspeakers and

other equipment Follow the installation instructions for the integrated amplifier on pages 4 and 5. AUDIO IN – Connect this input to the output sockets of your pre- amplifier or the PRE OUT sockets of an integrated amplifier. MONO LINK – The power amplifier can be adapted to provide two mono loudspeaker outputs from a single input. Pull out the link supplied and use it to connect the L and R AUDIO OUT so

POWER (and power indicator light)

Switches the unit on and off. The light indicates the status of the amplifier. When you switch your amplifier on, the light glows amber for a few seconds, during which time the speakers are disconnected. The light changes to green when the amplifier is ready for use. A red light means the amplifier is in standby mode. The power light may flash if a fault has occurred, with the colour of the flashing ligh

Arcam A90 Before you start

WARNING: Do not make any connections to your amplifier while it is switched on or connected to the mains supply. Before switching on please check all connections thoroughly, making sure bare wires or cables are not touching the amplifier in the wrong places (which could cause short circuits) and you have connected positive (+) to positive and negative (–) to negative. Always ensure that the volume control on your amplifier is

Arcam A90 The following table gives the IR-commands accepted by the

A90. Power commands Command Decimal Code Power toggle 16–12 Power-on 16–123 Power-off 16–124 Source selection commands Command Decimal Code PHONO select 16–1 AV select 16–2 TUNER select 16–3 DVD select 16–4 TAPE select 16–5 VCR select 16–6 CD select 16–7 AUX select 16–8 Volume control commands Command Decimal Code Mute 16–13 Volume up 1

Continual improvement policy

Arcam has a policy of continual improvement for its products. This means that designs and specifications are subject to change without notice. NOTE: All specification values are typical unless otherwise stated. Before returning your amplifier for service, please check the following: Sound cuts out for no reason If the temperature of the internal heatsink rises above a safe level, then a thermal cu

This entitles you to have the unit repaired free of charge, during

the first two years after purchase, at any authorised Arcam distributor provided that it was originally purchased from an authorised Arcam dealer or distributor. The manufacturer can take no responsibility for defects arising from accident, misuse, abuse, wear and tear, neglect or through unauthorised adjustment and/or repair, neither can they accept r

Arcam Amplifier Owners Instructions: