Argox AS-8000 Operation & User’s Manual

the limits for a Class a digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide a reasonable protection against harmful interface when the equipment is operated under a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interface t ...

The ArgoxScan can automatically scan barcode at a distance. Simply aim and pull the trigger. Code scanning is performed along the center of the light bar emitted from the reading window. This bar must cover the entire code. Successful scanning shall be obtained by tilting the scanner with respect to the barcode to avoid direct reflections that impair the reading performance. Recommended Steps When the required settings have been co ...

Introduction…………………………..………………. 1 Default Setting ………………………………………. 2 ArgoxScan 8000 specification …………………….. 3 Programming the ArgoxScan 8000 Series Scanner 6 Chapter 2 Parameter Setting Interface……………………………………………….… 8 Interface Selection ………………………………….. 8 Keyboard wedge …………� ...

74 RSS-14 ………………………………………………. 76 RSS-Limited…………………………………..…… 78 RSS-Expanded…………………………………..….. 80 China Post …………………………………………… 82 Italian pharmacode ………………………………… 84 Appendix� ...

1) First of all, you must switch off power for the terminal/computer. 2) Disconnect the keyboard cable from the back of the terminal/computer and connect to the interface cable of the scanner. 3) Connect the interface cable of the scanner to the terminal/computer. 4) Turn the terminal/computer power on. RS-232 1) Disconnect power to the terminal/computer. 2) Connect the external power supply (DC adapter) to the i ...

Code Type Read Enable Checksum Verification Enable Checksum Transmission Enable Code ID UPC-A V V V A UPC-E V V V E EAN-13 V V V F EAN-8 V V V FF Code-39 V ＊ Interleaved 2 of 5 V I Industrial 2 of 5 - - I Matrix 2 of 5 B Codabar % Code-128 V V # Code-93 V two digits & Code-11 V One digit O MSI/Plessey V @ UK/Plessey V @ Telepen S Standard 2 of 5 I RSS-14 - - R4 RSS-Limited - - RL RSS-Expanded - - RX Chin ...

Cable – K/B wedge Straight 2.0 m ArgoScan 8000 series Specification Model AS-8000 series Operational Light Source 660 nm Visible Red LED Optical System 2048 pixel CCD (Charge-coupled device) Depth of Scan Field 0-180 mm (CODE 39, 500Lux, PCS=90%, 20mils) Scanning Width 50 mm wide @ 10mm Scan Speed 100 scans/sec Resolution 0.1mm (4mils) Code39,PCS=90% Print Contrast 45% or more Scanning Angle Pitch: ...

Case material ABS plastic Cushion material TPR Electrical Input Voltage 5 VDC ± 0.25V Power - Operating Max. 750 mW Power - Standby 150 mW Current - Operating Max. 150 mA @ 5 VDC Current - Standby 30 mA @ 5 VDC DC Transformers Class 2; 5VDC @ 450 mA Agency listing FCC Class A, CE Environmental Operating Temperature 0℃ to 45℃ (32℉ to 113℉) Storage -20℃ to 60℃ (-4℉ to 140℉) Humidity 10% to 90% rel ...

DOS command through RS-232 (RS-232 model) Programmable characteristics Code type selection, check digit selection, Decoding option Transmitted character delay, Header selection, trailer selection, message suffix, good read beep tone and volume, scanner trigger selection Keyboard emulation type (intermessage delay, keyboard type and keyboard language) Serial interface type (ACK/NAK, Xon/Xoff ...

Series Scanner To program the 8000 series scanner, you must scan a series of programming barcode in the correct order. Fold out the back cover of this manual. You will see a table of alphanumeric barcodes, which are used to program the various options presented. To program each option, you must: 1. Scan the Program barcode on the parameter setting part. 2. Enter the option mode by scanning the Option Bar Code (also on the Pa ...

Option Alphanumeric Entry Scanning mode Good-read off Momentary Alternate Timeout off Continue Test only 00 01＊ 02 03 04 05 Program Exit Program Barcode Option Barcode Exit Barcode Back Fold Out Finish barcode ...

supports interfaces such as keyboard wedge, RS232 serial, and the latest USB interface. You will need to select an appropriate model for a specific interface. Interface selection: The factory interface default can not be changed for other type interface. One specific model only supports the appropriate host interface. For the appropriate model number of AS-8000 to various PC comp ...

popular PCs and IBM terminals. The installation of the wedge is a fairly simple process without any changes of software or hardware. Keyboard Type: AS-8000 keyboard wedge model only supports keyboard interface with PS/2 type connector. Option Bar Code Option Alphanumeric Entry Keyboard type IBM PS/2 Reserved Reserved Reserved Reserved Reserved Reserved 00＊ 01 02 03 04 05 06 ...

supports many country languages other than USA keyboard layout. First you need to confirm country language that you desire. In DOS, using command “keyb” to select the desirable keyboard layout or in WINDOWS entry “Control” then pops “Keyboard” to select country at “language” item. For details, please refer to your DOS or WINDOWS user’s manual. Keyboard Speed: By selecting ...

8 : low clock rate 00-08 03＊ Function key Disable Enable 00 01＊ Numeric key Alphabetic key Numeric keypad (Num lock state only) Alt+Keypad 00＊ 01 02 ...

scanner can get Caps Lock status. Power-on simulation: All of the PCs check the keyboard status during power-on selftest. It is recommended to Enable function if you are working without keyboard installation. It simulates keyboard timing and pass keyboard present status to the PC during power-on. Inter-character delay: This delay is inserted after each data characters transm ...

Option Alphanumeric Entry Caps lock Caps lock”ON” Caps lock”OFF” 00 01＊ Power-on simulation Disable Enable 00＊ 01 Inter-character delay 00-99 msec 00-99 02＊ Block transmission delay 00-99 10 msec 00-99 10＊ Program ...

RTS: Request To Send (Hardware Signal) Xon: Transmit On (ASCII Code 1116) Xoff: Transmit Off (ASCII Code13 16) Flow control: None-The communication only uses TxD and RxD signals without regard for any hardware or software handshaking protocol. RTS/CTS-If the scanner wants to send the barcode data to host computer, it will issue the RTS signal first, wait for the CTS signal from the host computer, and then perf ...

Option Alphanumeric Entry Flow control None RTS/CTS Xon/Xoff ACK/NAK 00＊ 01 02 03 Inter-character delay 00-99 (msec) 00-99 00＊ Block transmission delay 00-99 (10 msec) 00-99 00＊ Response delay 00-99 (100 msec) 00-99 20＊ Program ...