Fiplex DH140-R User & Installation Manual

General Review 2.0 March 2nd, 2016 General Update 3.0 7 June, 2017 ...

This manual describes installation, commissioning, operation and maintenance of the Fiplex DH140-R Digital Remote Unit, and Fiplex Control Software (FCS). . The first part of the manual describes the Digital Fiber DAS hardware and the second part describes the software. Hardware and software mentioned in this manual are subjected to continuous development and improvement. Consequently, there may be minor discrepancies between ...

AMPS Advanced Mobile Phone Service ARFCN Absolute Radio Frequency Channel Number BCCH Broadcast Control Channel (GSM broadcast channel time slot) BS Base Station, BS antenna = towards the base station CDMA Code Division Multiple Access DC Direct Current DCS Digital Communication System (same as PCN) DL Downlink signal direction (from base station via repeater to mobile station) DPLX Duplex filter EEPROM E ...

1. Safety Caution! This manual lists a set of rules and warnings to be accomplished when installing, commissioning and operating a Fiber DAS Master Optical Unit from FIPLEX. Any omission may result in damage and/or injuries to the System and/or the System Operators or Users. If an instruction is not clear or you consider is missing, please contact immediately to Fiplex. See www.fiplex.com for contact information. Dangerous Voltage ...

Never view a laser pointer using an optical instrument, such as binocular or a microscope. Never handle non-dark fibers. RF Exposure. As a part of a Telecommunications System, MOU1x is not intended to radiate signals and meets EMC directives, but within the System may have cables and antennas that are potential sources of radiating. Contact the System De ...

WARNING: This is a 90.219 Class B device. This is NOT a CONSUMER device. It is designed for installation by FCC LICENSEES and QUALIFIED INSTALLERS. You MUST have an FCC LICENSE or express consent of an FCC Licensee to operate this device. You MUST register Class B signal boosters (as defined in 47 CFR 90.219) online at www.fcc.gov/signal- boosters/registration. Unauthorized use may result in signifi ...

The DH140-R is an FPGA based Digital Fiber Optic Remote Unit that transmit in the Downlink frequencies of160- 162MHz and receives in the Uplink frequencies 153-162MHz for United States. This Remote Unit extends the radio coverage into areas inside the Base Station range where propagation losses prevent reliable communication. The DH140-R is fed by fiber via a Digital Master, the DH100-M. The DH100-M is connected directly t ...

The Digital Master Unit is equipped with internal duplexers, therefore, the enclosure has the “To Base” RF Port. ...

The Digital Remote Unit is equipped with internal duplexers, therefore, the enclosure has the “To Mobile” RF Port. ...

Note: Each fiber connection is performed with simplex fiber and LC-APC connector. ...

Note: Each fiber connection is performed with simplex fiber and LC-APC connector. ...

Fiplex Digital DAS is designed for outdoor usage with a weather proof outdoor NEMA4 cabinet that can be mounted without any kind of shelter from rain, snow or hail. However, to improve reliability, it is recommended to mount the Digital DAS on a site with shelter from direct exposure to sun, rain, snow and hailing. It is not recommended to operate the DAS under bad weather conditions, such as: - Intense rainfa ...

provided four M6 x 1/2” allen screws. Figure 4 ...

To open the cabinet, release the 8 door screws indicated in figure 5 using the provided special allen key. A - Release cabinet cover. Figure 5 Use the special allen key N°6 ...

Figure 6 C – Close the cabinet cover. Figure 7 ...

The unit has available a Liquid Tight Conduit Fitting connector. The unit as standard has the connector installed, so if the user requires to use this connector, if available, the NFPA cables, Ethernet, DC and AC cables can be routed through this connector. Figure 9; AC Routing through cable gland or conduit connector If the is not going to use Liquid Tight Conduits, then the connector should be replaced by the provid ...