ASA Electronics AOC-75 Operation Manual

Text of ASA Electronics AOC-75 Operation Manual

ASA Electronics AOC-75 High resolution, 1/3” CCD Camera

- Compact/Lightweight Aluminum Die Cast Body - Waterproof Housing - Waterproof Microphone - Waterproof Normal/Mirror Image Switch - Optional Wind deflector AOM-58 Features - 5” Monochrome Monitor - Dual camera Input - Brightness/Contrast/Day-Night Controls - Volume Control for Internal/External Speaker - Power/Stand By Button - Back-lit Front Panel Controls OCA-80 Features - 2

The Voyager Observation system (AOS58) has been designed to provide

years of trouble free operation. Please read this manual thoroughly. This manual contains instructions to ease the installation of the camera and monitor. The Voyager Observation system is a supplement to the standard rear view mirror systems, and will provide additional rear view vision when installed and maintained properly. The Voyager observation System is not int

Use without Wind Deflector Screws (#8-32 UNC x 7.5)

4 Use with Wind Deflector Screws (#8-32 UNC x 9.0) AOM-58 Monochrome Monitor Qty. 1 5” Monitor 1 Snap-On Sun Visor 1 Monitor Bracket 1 Power Harness with locking connector 1 Range marker 4 Thumb screws (M5 x 15) with plain washer and spring washers 4 Attachment screws with washers (M5 x 12) OCA-80 Cable Qty. 1 20 meter cable with waterproof connector. Oil, gas, and grease resistant. UV stable Documen

2. Attach camera to bracket using 8-32 UNC screws provided. Adjust

angle as indicated in Figure 2. Use rear or end of bumper as reference point. 3. Wind deflector may be installed. This deflector is designed to reduce the build-up of dust, dirt and moisture on the camera lens. (See Figure 3). AOM-58 MONITOR 1. Attach monitor inside vehicle in a location convenient to the driver (e.g. center of dash, overhead, or in dash). 2. Use a compression plate to a

4. To increase protection of cable, place all excess wire and extension

cable in convoluted tubing. 5. Do not twist camera cable, do not cut pigtail, or cable. WIRING CAMERA AND MONITOR 1. See wiring diagram for connections to ignition, ground, and backup circuit. (See Figure 6) 2. Wiring camera: Drill a 19mm /3/4” diameter hole into the vehicle body near the camera and bracket. Connect camera connector to extension cable in vehicle. Push extra cable in

“Day/Night” switch does not achieve the most

desirable picture. 5. Brightness: Variable control of brightness. Should be adjusted if the “Day/Night” switch does not achieve the most desirable picture. 6. Volume: Variable control of internal speaker and external speaker volume. REAR OF MONITO

3. Affix the “STOP” marker on the monitor screen over the image of the

rear view bumper to locate the rear bumper. 4. The monitor screen is now “calibrated” for distances behind the vehicle of 3 feet, 6 feet and 9 feet. 5 High-Mounted, Centered Camera Assembly Location Camera Assembly Location, High- Mounted Centered

Without Wind Deflector

Screw for use w/Wind deflector #8-32 x 3/8" #8-32 x 5/16" Screw for use Included Wind Deflector- Optional Installation 4mm x .7mm Phillips Hex Head Screw w/Washers 4mm x .7mm x 25.4mm 4mm x .7mm x 25.4mm Phillips Hex Head Screw w/Washers 4mm x .7mm Hex Nuts Hex Nuts

Steel Plate Reinforcement (Recommended for Secure Mounting)

Figure 4 9 Plain Washer Spring Washer Dashboard or Overhead

Monitor Mounting Hole Pattern

Figure 5 10 20° 20° 5.275 6.240 2.250 2.677 110.0° 5-0.236 Dia. Holes

EMI FERRITE CORE

REAR OF MONITOR (FEMALE BULLET DISCONNECT) 18 TEW BLK (Ground) 18 TEW BLU (Reverse Trigger) 18 TEW RED (12V) TO MONITOR CAMERA "A" INPUT TO MONITOR 20 METERS WIND DEFLECTOR- OPTIONAL INSTALLATION WATERPROOF CAMERA CONNECTION GROMMET TO SEAL THROUGH VEHICLE INTERIOR 18 TEW YEL (Battery) (MALE BULLET DISCONNECT) (STRIPPED AND TINNED) (STRIPED AND TINNED) 3A 1A

ASA Electronics AOC-75 MONITOR FRONT VIEW

MONITOR REAR VIEW Monitor Operating Controls and Connections 12 4 3 2 1 6 1 2 4 3 5 A B

ASA Electronics Automobile Accessories Owners Instructions: