Asko 1325 Installation Instructions Manual

Text of Asko 1325 Installation Instructions Manual

Asko 1325 OMATIC HIGH L

TIC HIGH L TIC HIGH L TIC HIGH L TIC HIGH LOOP OOP OOP OOP OOP TTTTThe dr he dr he dr he dr he drain hose is f ain hose is f ain hose is f ain hose is f ain hose is fastened to the astened to the astened to the astened to the astened to the back of the machine at the best back of the machine at the best back of the machine at the best back of the machine at the best back of the machine at the best hig

Phillips No. 2 screwdriver

2) Flat blade screwdriver 3) Torx screwdriver size T 20 4) Adjustable wrenches (if you use copper fittings) 5) Open-ended wrench (1/2" [12 mm] or 5/8" [16 mm]) 6) Wire cutters and strippers 7) Tape measure 8) Spirit level 9) Electric drill with 1” drill bit 10) Keyhole saw TECHNICAL D TECHNICAL D TECHNICAL D TECHNICAL D TECHNICAL DAAAAATTTTTAAAAA Water pressure 18-176 psi Power 120 v, 60

WARNING! Plumbing connections must comply with

applicable sanitary, safety and plumbing codes in your area. The machine should preferably be connected to a hot water supply. If a cold water supply is used, the washing times will be longer but the performance will not be affected. The hot water supply line should be minimum 3/8" OD copper tubing. The inlet valve has a 3/8" NPT female connection. After determining where the water supply line will en

ASKO provides a 7/8” drain hose which is connected to

the back of the unit to form a high loop. If additional drain hose is needed, please purchase an additional ASKO drain hose and joint it to the provided hose with a 7/8” copper tube. NOTE: Do not use any fittings anywhere in the drain line that are less than 7/8" ID. The access hole for the drain line should be 1-1/2". The end of the drain line is 1/2”, but it is adjustable to 7/8”, 3/4�

Before working on wiring for any

electrical appliance, be sure the electrical power has been turned off at the breaker/fuse box. WARNING! Disconnect electrical power supply and place a tag at the disconnect switch indicating that you are working on the circuit. WARNING! Electrical and grounding connections must comply with the applicable portions of the national electrical code and/or other local electrical codes. This unit must be grounded

Position the machine in front of the cabinet

opening. 2. Make the height adjustment while the dishwasher is in front of the opening. 3. Pull out the drain hose to ensure there are no sharp bends. 4. On the bottom rear of the dishwasher there is a black ziptie around the rubber buffer that holds the circulation pump in place. Cut the ziptie and remove it. 5. Start to feed water, electric, and drain lines into position. 6. Make sure you’ve put th

TESTING FOR LEAKS

TESTING FOR LEAKS TESTING FOR LEAKS TESTING FOR LEAKS TESTING FOR LEAKS 1. Turn on the water supply and check for leaks. 2. Turn the power on at breaker/fuse box and test the dishwasher operation by running a Rinse cycle. (This should take about four minutes.) 3. Turn off the electrical power and check for leaks In order to prevent heat damage to the inlet valve, all solder connections must be made before the water line is connecte

Asko 1325 WARNING! Before working on any electrical

appliance, be sure the electrical power has been turned off at the breaker/fuse box. Refer to the illustration at right for instruction references. 1. Remove the lower access panel with standard or 20 torx screwdriver. 2. Using needlenose pliers, remove the plastic plugs around the edges of the access panel and upper door panel. You may discard the plugs. 3. Using the screws provided with the trim kit, loo

The 1805FI can only be installed with a custom door

panel that extends from the toe kick to the counter top. The unit comes with everything needed to make installing the door panel easy. The door is predrilled for the panel’s mounting screws. The custom panel should be at least 1/4” thick. ITEMS PR ITEMS PR ITEMS PR ITEMS PR ITEMS PRO OO O OVIDED VIDED VIDED VIDED VIDED WITH WITH WITH WITH WITH THE UNIT THE UNIT THE UNIT THE UNIT THE UNIT ♦Tw

h TTTTToe Kic

oe Kic oe Kic oe Kic oe Kick Installa k Installa k Installa k Installa k Installations tions tions tions tions Custom panels the same height as the dishwasher door If the custom panel is the same height as the dishwasher door, a 2” decorative fill strip or pull-out cutting board must be used to fill the area between the panel and the counter top (as illustrated below). Panel extends from toe kick

Model 1895 was designed to easily accommodate

custom panels. If you use the 4” toe kick, a 2” filler strip or a pullout cutting board above the unit will be necessary. The opening width for Model 1895 is 23-5/8” (600 mm), which is 3/8” narrower than standard domestic dishwashers. ITEMS PR ITEMS PR ITEMS PR ITEMS PR ITEMS PRO OO O OVIDED VIDED VIDED VIDED VIDED WITH WITH WITH WITH WITH THE UNIT THE UNIT THE UNIT THE UNIT THE UNIT ♦Two sho

Asko Dishwasher Owners Instructions: