Ada Ez Pro Quick Start Manual
Read Online
Read the Ada Ez Pro Quick Start Manual online using the built-in PDF viewer.
Pro Quick Start Manual: Key Pages of Document
© 2012 ADA EZ. ALL RIGHTS RESERVED. 1 of 12 Quick-Start Guide ADA EZ Pro Pull-Side Operator Quick-Start Guide 700302 Rev. A, 10/14/12 ADAQS01 PULL-SIDE APPLICATION (RIGHT HAND DOOR SHOWN) PULL-SIDE APPLICATION (LEFT HAND DOOR SHOWN) This manual provides quick-reference instructions for installing and operating the pull-side ADA EZ swing door operator. Prior to performing these instructions thoroughly review the following information in document number 70002, “ADA EZ Pro Installation and Operating Instructions:” • System Description • Detailed operator programming instructions • Prerequisites • Replacing the battery ...
© 2012 ADA EZ. ALL RIGHTS RESERVED. 2 of 12 Quick-Start Guide TABLE OF CONTENTS 1.1 Installing the Operator Mounting Template ................................................................................................. 2 1.2 Mounting the Door Shoe .............................................................................................................................. 3 1.3 Installing the Operator Mounting Bracket and Cover .................................................................................. 5 1.4 Installing the Door Operator ................................................................................ ...
© 2012 ADA EZ. ALL RIGHTS RESERVED. 3 of 12 1.2 Mounting the Door Shoe 1.2.1 If the door frame is steel or aluminum and rivnuts must be installed, refer to Figure 2 and PERFORM the following: a. Using a 25/64″ drill, DRILL the door arm pivot bracket holes. b. Using a rivnut tool, INSTALL the ¼-20 steel rivnuts. c. INSTALL and TIGHTEN the two (minimum) ¾″ (19.05 mm) socket head capscrews with washers) securing the door arm pivot bracket to the underside and face of the frame header. 1.2.2 If the door frame is wood, refer to Figure 2 and PERFORM the following: a. Using a 5/32″ (3.97 mm) drill, DRILL the door arm pivot bra ...
© 2012 ADA EZ. ALL RIGHTS RESERVED. 4 of 12 Figure 2. Mounting the Door Shoe ADAQS03 ...
© 2012 ADA EZ. ALL RIGHTS RESERVED. 5 of 12 1.3 Installing the Operator Mounting Bracket and Cover CAUTION For light-duty or hollow-core doors with insufficient top rail blocking, through bolts or sex nut and bolts are required to securely attach the operator mounting bracket. To ensure proper installation, the operator must be fastened with at least four fasteners. For heavier doors more fasteners are recommended. 1.3.1 If the door is aluminum and rivnuts must be installed, refer to Figure 3 and PERFORM the following: a. Using a 25/64″ drill, DRILL the mounting bracket holes. b. Using a rivnut tool, INSTALL the ¼-20 steel r ...
© 2012 ADA EZ. ALL RIGHTS RESERVED. 6 of 12 1.4 Installing the Door Operator 1.4.1 REMOVE the dress cover from the operator. WARNING To avoid inadvertent activation of the operator during connection of the door arm, the battery pack should not be installed until after the door arm is connected. 1.4.2 Refer to Figure 4, and, with the battery pack facing the jamb, POSITION the operator onto the operator mounting pins. ENSURE operator does not slide off the mounting pins. 1.4.3 INSTALL and TIGHTEN the two ¼-20 X 1½″ socket head capscrews securing the operator to the operator mounting pins. 1.5 Installing the Door Arm 1.5.1 Ref ...
© 2012 ADA EZ. ALL RIGHTS RESERVED. 7 of 12 1.5.3 Refer to Figure 6, and ADJUST door arm length to 8 1/16″ (204.77 mm). 1.5.1 Refer to Figure 7, and, with the door arm coupling screws facing up, POSITION the larger end of the door arm onto the operator output shaft. CAUTION The door arm coupling is a two-piece tapered coupling. To draw the coupling halves together evenly the three door arm coupling screws must be tightened evenly (one quarter turn at a time) until fully tight. 1.5.2 While maintaining the door arm position, TIGHTEN the door arm coupling screws evenly (one quarter turn at a time) until fully tight. 1.5.3 INSTAL ...
© 2012 ADA EZ. ALL RIGHTS RESERVED. 8 of 12 1.6 Installing the Optional Plug-In Transformer NOTE If possible, the transformer wiring should be routed against the door trim molding. 1.6.1 ROUTE transformer wiring to a 110-VAC outlet, but do not plug transformer into the outlet. NOTE An optional plug-in transformer is recommended in installations where the automatic door-opening feature will be used frequently. The optional plug-in transformer is REQUIRED for installations where Power Close and/or Push and Go features are enabled. 1.6.2 Refer To Figure 8, and ROUTE wires through armored cable end links. MOUNT the door cord end l ...
© 2012 ADA EZ. ALL RIGHTS RESERVED. 9 of 12 1.6.3 Refer to Figure 9, and PLUG connector into receptacle on battery pack. 1.6.4 Refer to Figure 10, and VERIFY that the LED indicator lights GREEN. Figure 9. Plugging the Connector into the Receptacle CONNECTOR COVER CONNECTOR PLUG CONNECTOR RECEPTACLE EZ060 Figure 10. Verifying that the LED Illuminates LED INDICATOR ADAEZ60 ...
© 2012 ADA EZ. ALL RIGHTS RESERVED. 10 of 12 1.6.5 Refer To Figure 11, and INSTALL receptacle cover onto battery pack. Figure 11. Plugging the Receptacle Cover onto the Battery Pack EZ062 ...
© 2012 ADA EZ. ALL RIGHTS RESERVED. 11 of 12 1.7 Programming the Operator 1.7.1 Refer to Figure 12, and, at the base of the controller, PRESS and HOLD the “SELECT” and “ENTER” pushbuttons for three seconds. The following shall occur: • The operator shall enter program mode. • The four LEDs on the circuit board shall repeatedly flash green. • The “CLS” position LED shall illuminate red and remain lit. 1.7.2 With the door in the closed position, PRESS the “ENTER” pushbutton. The following shall occur: • The “CLS” position LED shall flash green. • The “OP” (open) position LED shall illuminate red ...
© 2012 ADA EZ. ALL RIGHTS RESERVED. 12 of 12 1.7.6 With the door in the fully closed position, PRESS the “ENTER” pushbutton. The following shall occur: • The door shall open quickly and then close. • The “AUTO SETUP” led shall illuminate green. 1.7.7 PRESS and HOLD the “ENTER” pushbutton for three seconds. The following shall occur: • The “AUTO SETUP” led shall go out. • The second LED (not labeled) shall flash green. • The door shall be tuned. 1.7.8 To reset the controller, PERFORM the following: a. PRESS and HOLD the “RESET” pushbutton. b. PRESS and HOLD the “ENTER” pushbutton. c. RELEASE the ...
Door Opening System PDF Instructions
1 GEZE TS1000 Overhead Door Closer WARNING: DOOR CLOSERS WITH A POWER RATING LOWER THAN 3 OR WITH MECHANICAL HOLD OPEN DEVICES ARE NOT SUITABLE FOR USE WITH FIRE DOORS. Components Checklist: 1x Closer body & cover 1x Guide Rail Assembly 2x M6 Allen Bolts 2x Pl Device operation guide for the GEZE TS1000 Door Opening System. The manual provides information on troubleshooting, troubleshooting guides, installation procedures, compatibility information.
24739476 NOTE: If door does not have a cutout for cabling inside lock stile, door must be routed. Refer to 33/3550AWDC wood door template #24731408. ! 1-Point Latch (LBL) 2-Point Latch includes these additional parts Fire-Rated D Service and user manual for the Von Duprin 3550AWDC Door Opening System. It provides information on safety and hardware components, startup procedures, performance optimization.
68MB000009 instruction manual revision GENERAL This appendix contains changes that have been made since the printing of your Owner’s Guide number 68P02952C60-A. Use this information to update your Owner’s Guide. REVISION DETAILS The new model numbers are M Device guide for the Micom 2ES ALE Door Opening System. This manual covers installation, operation, and hardware setup, device calibration, technical troubleshooting.
Cat AUTOMAZIONI PER CANCELLI SCORREV OLI AUTOMATISME POUR POR TAIL COULISSA TES AUTOMATION FOR SLIDING GA TES AUTOMATISIERUNG FÜR SCHIEBET ORE AUTOMATIZACIONES P ARA CANCELAS CORREDERAS Mover Manuale d’Installazione e d’Uso Manuel d'Installation et Utilis Owner’s guide for the ADG Mover Door Opening System. It provides information on installation and daily usage, device calibration, component replacement.