Ask Proxima M9 Operation & User’s Manual

Using the User Documentation on the CD-ROM.......................................................................... 2 Register with ASK Proxima........................................................................................................... 2 Important Lamp Information..... ...

The CD-ROM that comes with the projector has a PDF file “Reference Guide” that contains detailed explanations about projector operations. In order to read the Reference Guide, you need to have Adobe® Reader® installed on your computer. If you don't, go to www.adobe.com to download and install it. It's quick, easy, and secure. Activate ...

* The projector’s enter key does not have anything printed on it. When you see [ENTER] in this manual, it means you should press the projector’s enter key or the [ENTER] key of the remote controller. Warning z Never look into the lens while the projector is turned on. z Never allow the intake and exhaust vents to become blocked, and make sure there is at least 30 cm ( ...

Warning z In the unlikely event of a lamp rupture, particles may be ejected from the projector. Keep out of the area under and around the projector when it is turned on. See the safety instructions booklet for more details. Elevation adjustment foot Left, right adjustment feet (2) Lamp cover Elevation adjustment foot release button Anti- ...

remove the battery insulation sheet from the back of the remote controller. z To avoid running down the battery, store the remote control unit so its buttons are not pressed inadvertently. Remote Controller General Guide Preparing the Remote Controller [INPUT] key [AUTO] key [ ] (Power) key Remote control signal emitter [ZOOM +] [ZOOM –] ...

comes with it. Replacing the Remote Controller Battery Caution RISK OF EXPLOSION IF BATTERY IS REPLACED BY AN INCORRECT TYPE. DISPOSE OF USED BATTERIES ACCORDING TO THE INSTRUCTIONS. Caution Misuse of a battery can cause it to leak and stain the area around it, or to explode, creating the risk of fire and personal injury. Make sure that you always ...

sufficient space around the sides and back of the projector for proper ventilation. z The following illustrations show how the projector should be oriented for optimum projection relative to the screen. z You can place the projector on a surface that is angled up to 30 degrees upwards or downwards during use. Never locate the pro ...

also make fine adjustments to the left and right side elevation angle when necessary. To change the projector elevation angle 1. Lift up the front of the projector and press the release button. z This causes the elevation adjustment foot to drop from the bottom of the projector. z Be sure to press the release button before trying to lower the elevatio ...

z Always turn off the projector and the computer before connecting them. You can use the projector to project an image from a video deck, TV, video camera, or other video device. z Always turn off the projector and the video device before connecting them. z You can use the bundled video cable to connect to a pin jack (RCA) type VIDEO output terminal. When ...

and connect to an output device. AC Power Cord Precautions z Use the AC power cord that comes with the projector. z Make sure that you use a power source with the same voltage as that specified for the projector. z Do not share the outlet supplying power to the projector with other devices. If you are using an extension cord, make sure that th ...

z If the projector is hot when you plug the AC power cord into a power outlet, it will go into a cool down state. The cool down state is indicated by the POWER/STANDBY indicator flashing orange. Note that the projector will not turn on until cool down is complete, even if you press the [ ] (power) key. The projector will turn on and enter the s ...

down state. Note that you will not be able to turn the projector back on again while it is cooling down. z The projector may remain quite hot for a while after you turn it off. Take care when moving the projector or otherwise handling it after use. z Make sure that the projector is cooled down sufficiently before storing it. To turn off the projector 1. ...

CD-ROM that comes with the projector. When you turn on the projector, it first checks the RGB terminal for an input signal and then the VIDEO terminal. When it detects an input signal, it automatically selects it and starts projecting the signal. Whenever you want to manually trigger an input source search operation, press the ...

When the input source is RGB (computer), the projector automatically adjusts vertical and horizontal positioning, frequency, and phase whenever it detects an RGB signal (following input source selection, power up, etc.). You can also execute an automatic adjustment operation by pressing the [AUTO] key. z You can turn off auto adjustment when you want to disable auto adjustment and maintain manual settings ...

English Using the Setup Menu Pressing the [MENU] key while an image is being projected displays the setup menu on the projected image. The setup menu can be used to configure a variety of different projector settings. Use the cursor keys to select and configure settings, and the [ENTER] key to register them. The menu items that can be set (or displayed) depend on the current input source. In the following table, the “Input Source� ...

section provides details about indicators. z “POWER” in the following table stands for the “POWER/STANDBY” indicator. Normal Operation Indicators Error Indicators and Warning Messages When an error occurs, wait until cool down is complete and the fan stops before unplugging the AC power cord. If you unplug the AC power ...

Amber steady : Red flashing (1-second interval) J Turns off : – Power has turned off automatically due to internal overheating. Perform the following steps.  Check for any blocking of the projector’s intake vents and exhaust vents, and make sure that there is sufficient space around the projector.  If there is dust accumulated around the intake vents and/or exhaust vents, remove it. If t ...

: – : – Zoom and focus cannot be performed due to some trouble in the optical drive circuit. Turn off the projector and then turn it back on again. If the error occurs again when you turn power back on, contact ASK Proxima service at www.askproxima.com/service Press the [ESC] key to clear the warning message. Message : Zoom and focus cannot be performed for some reason. Try turning the projector off and ...

: – : Red flashing (1-second interval) It is time to replace the lamp. Replace the lamp following the steps under “Replacing the Lamp” in the Reference Guide on the CD-ROM that comes with the projector. Press the [ESC] key to clear the warning message. Message : It is time to replace the lamp. Use the procedure in the User’s Guide to replace the lamp as soon as possible. POWER TEMP LAMP : Am ...

Projector Troubleshooting Problem Cause and Recommended Action See The projector does not turn on when I press the [ ] (power) key. If the POWER/STANDBY indicator is not lit, the AC power cord may not be connected correctly. ➔Make sure the AC power cord is connected correctly to the projector and the power outlet (see “Turning On the Projector”). page ...