Philips SCC2691 Product Data Sheet

Text of Philips SCC2691 Product Data Sheet

Philips SCC2691 Product data sheet

Supersedes data of 1998 Sep 04 2006 Aug 04 INTEGRATED CIRCUITS
Product data sheet SCC2691 Universal asynchronous receiver/transmitter (UART) 2 2006 Aug 04 DESCRIPTION The Philips Semiconductors SCC2691 Universal Asynchronous Receiver/Transmitter (UART) is a single-chip CMOS-LSI communications device that provides a full-duplex asynchronous receiver/transmitter. It is fabricated with Philips Semiconductors CMOS technology which combines the benefits of high density and low power consumption. The
Product data sheet SCC2691 Universal asynchronous receiver/transmitter (UART) 2006 Aug 04 3 ORDERING INFORMATION COMMERCIAL INDUSTRIAL PACKAGES VCC = +5V +10%, TA = 0°C to +70°C VCC = +5V +10%, TA = –40°C to +85°C VERSION 24-Pin Plastic Dual In-Line Package (DIP) SCC2691AC1N24 SCC2691AE1N24 SOT222–1 28-Pin Plastic Leaded Chip Carrier (PLCC) Package SCC2691AC1A28 SCC2691AE1A28 SOT261-2 24-Pin Plastic Small Outline Large (SOL)
Product data sheet SCC2691 Universal asynchronous receiver/transmitter (UART) 2006 Aug 04 4 PIN DESCRIPTION MNEMONIC PIN NO. TYPE NAME AND FUNCTION MNEMONIC DIP PLCC TYPE NAME AND FUNCTION D0–D7 22–15 27, 25, 24, 22–18 I Data Bus: Active-high 8-bit bidirectional 3-State data bus. Bit 0 is the LSB and bit 7 is the MSB. All data, command, and status transfers between the CPU and the UART take place over this bus. The direction of
Product data sheet SCC2691 Universal asynchronous receiver/transmitter (UART) 2006 Aug 04 5 ABSOLUTE MAXIMUM RATINGS1 SYMBOL PARAMETER RATING UNIT TA Operating ambient temperature range2 Note 4 °C TSTG Storage temperature range –65 to +150 °C VCC Voltage from VCC to GND3 –0.5 to + 7.0 V VS Voltage from any pin to ground3 –0.5 to VCC +10% V PD Power Dissipation 300 mW NOTES: 1. Stresses above those listed under Absolute Maximu
Product data sheet SCC2691 Universal asynchronous receiver/transmitter (UART) 2006 Aug 04 6 AC ELECTRICAL CHARACTERISTICS1, 2, 3, 4 SYMBOL PARAMETER LIMITS UNIT SYMBOL PARAMETER Min Typ Max UNIT Reset timing (Figure 3) tRES Reset pulse width 100 ns Bus timing (Figure 4)5 tAS A0–A2 setup time to RDN, WRN low 10 ns tAH A0–A2 hold time from RDN, WRN low 100 ns tCS CEN setup time to RDN, WRN low 0 ns tCH CEN hold time from RDN, WRN h
Product data sheet SCC2691 Universal asynchronous receiver/transmitter (UART) 2006 Aug 04 7 BLOCK DIAGRAM As shown in the block diagram, the UART consists of: data bus buffer, interrupt control, operation control, timing, receiver and transmitter. Data Bus Buffer The data bus buffer provides the interface between the external and internal data busses. It is controlled by the operation control block to allow read and write operations
Product data sheet SCC2691 Universal asynchronous receiver/transmitter (UART) 2006 Aug 04 8 values of CTUR and CTLR at any time, but the new count becomes effective only on the next start counter command following a stop counter command. If new values have not been loaded, the previous count values are preserved and used for the next count cycle. In the counter mode, the current value of the upper and lower eight bits of the counter
Product data sheet SCC2691 Universal asynchronous receiver/transmitter (UART) 2006 Aug 04 9 In addition to the normal transmitter and receiver operation described above, the UART incorporates a special mode which provides automatic wake-up of the receiver through address frame recognition for multi-processor communications. This mode is selected by programming bits MR1[4:3] to ‘11’. In this mode of operation, a ‘master’ stati
Product data sheet SCC2691 Universal asynchronous receiver/transmitter (UART) 2006 Aug 04 10 parity mode is programmed. In the special wake-up mode, it selects the polarity of the transmitted A/D bit. MR1[1:0] – Bits Per Character Select This field selects the number of data bits per character to be transmitted and received. The character length does not include the start, parity, and stop bits. MR2 – Mode Register 2 MR2 is acces
Product data sheet SCC2691 Universal asynchronous receiver/transmitter (UART) 2006 Aug 04 11 Table 2. Register Bit Formats Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 MR1 (Mode Register 1) RxRTS Control RxINT Select Error Mode* Parity Mode Parity Type Bits per Character 0 = no 1 = yes 0 = RxRDY 1 = FFULL 0 = Char 1 = Block 00 = With parity 01 = Force pari
Product data sheet SCC2691 Universal asynchronous receiver/transmitter (UART) 2006 Aug 04 12 Table 2. Register Bit Formats (Continued) CTUR (Counter/Timer Upper Register) C/T[15] C/T[14] C/T[13] C/T[12] C/T[11] C/T[10] C/T[9] C/T[8] Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 CTLR (Counter/Timer Lower Register) C/T[7] C/T[6] C/T[5] C/T[4] C/T[3] C/T[2] C/T[1] C/T[0] CSR –
Product data sheet SCC2691 Universal asynchronous receiver/transmitter (UART) 2006 Aug 04 13 CR[1] – Disable Receiver This command terminates operation of the receiver immediately; a character being received will be lost. The command has no effect on the receiver status bits or any other control registers. If the special wake-up mode is programmed, the receiver operates even if it is disabled (see Wake-up Mode). CR[0] – Enable Re
Product data sheet SCC2691 Universal asynchronous receiver/transmitter (UART) 2006 Aug 04 14 to placing the SCC2691 in this mode. Note that this bit must be set to a logic 1 after reset. When the power-down mode is enabled, internal circuitry forces the X1/CLK pin to the low state and the X2 pin to the high state. If an external clock is being used to drive the device, it is recommended that the clock source be three-stated or forced
Product data sheet SCC2691 Universal asynchronous receiver/transmitter (UART) 2006 Aug 04 15 IMR – Interrupt Mask Register The programming of this register selects which bits in the ISR cause an interrupt output. If a bit in the ISR is a ‘1’ and the corresponding bit in the IMR is a ‘1’, the INTRN output is asserted (low). If the corresponding bit in the IMR is a zero, the state of the bit in the ISR has no effect on the IN
Product data sheet SCC2691 Universal asynchronous receiver/transmitter (UART) 2006 Aug 04 16 RDN MPI WRN MPO tPS tPH tPD SD00125 Figure 5. I/O Timing WRN INTERRUPT1 OUTPUT RDN INTERRUPT1 OUTPUT VM tIR tIR VOL +0.5V VOL +0.5V VOL VOL NOTES: 1. INTRN or MPO when used as interrupt outputs. 2. The test for open drain outputs is intended to guarantee switching of the output transistor. Measurement of this response is referenced from the
Product data sheet SCC2691 Universal asynchronous receiver/transmitter (UART) 2006 Aug 04 17 tTXD tTCS 1 BIT TIME (1 OR 16 CLOCKS) TxD TxC (INPUT) TxC (1X OUTPUT) SD00092 Figure 8. Transmit Timing tRXS tRXH RxC (1X INPUT) RxD SD00093 Figure 9. Receive Timing
Product data sheet SCC2691 Universal asynchronous receiver/transmitter (UART) 2006 Aug 04 18 TxD D1 D2 D3 BREAK D4 D6 TRANS- MITTER ENABLED TxRDY (SR2) WRN CTSN1 (MPI) (MPO) RTSN2 D1 D2 D3 START BREAK D4 STOP BREAK D5 WILL NOT BE TRANSMITTED D6 CR[7:4] = 1010 CR[7:4] = 1010 NOTES: 1. TIMING SHOWN FOR MR2[4] = 1. 2. TIMING SHOWN FOR MR2[5] = 1. SD00128 Figure 10. Transmitter Timing D1 D2 D4 D5 D6 D7 D8 D3 RxD RECEIVER ENABLED RxRDY
Product data sheet SCC2691 Universal asynchronous receiver/transmitter (UART) 2006 Aug 04 19 MASTER STATION TxD TRANSMITTER ENABLED TxRDY (SR2) CSN (WRITE] PERIPHERAL STATION RxD RECEIVER ENABLED RxRDY (SR0) RDN/WRN ADD#1 1 D0 0 ADD#2 1 BIT 9 BIT 9 BIT 9 BIT 9 BIT 9 BIT 9 BIT 9 BIT 9 MR1[4:3] = 11 MR1[2] = 1 ADD#1 MR1[2] = 0 D0 MR1[2] = 1 ADD#2 0 ADD#1 1 D0 0 ADD#2 1 0 MR1[4:3] = 11 ADD#1 D0 S D S = STATUS D = DATA S D ADD#2 SD00130