Festo SRBG Operating Instructions

Ruiter Straße 82 73734 Esslingen Germany +49 711 347-0 www.festo.com Operating instructions (Original instructions) 8075401 2017-07a [8075403] Sensor box SRBG English . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 Configuration 1.1 SRBG-…-C2-C2 4 2 5 6 1 7 8 3 1 Housing cover 2 Housing screws 3 Yellow LED, switching status indic­ ation for solenoid valve 4 Caged spring terminal 5 Cable entry M20 x 1.5 for system connection 6 Cable entry M12 x 1.5 for solenoid valve connection 7 Inductive dual sensor 8 Green LED, power supply indicator (only for SRBG-C1-N-1-P-C2-C2) yellow LED, switching status indic­ ation Fig. 1 1.2 SRBG-…-M12 3 1 2 1 Green LED, power supply indicator (only for SRBG-C1-N-1-P-M12) Yellow LED, switching status indic­ ation 2 Inductive dual sensor 3 M12 plug connection Configuration of SRBG-…-M12-M12 (� Chapter 4.2) Accessories � www.festo.com/catalogue. 2 Safety The sensor box is intended for recording, electrical feedback and optical display of the end positions of drives. Appropriate for operation are semi-rotary drives with a mechanical interface in accordance with VDI/VDE Directive 3845. – The product may only be used in its original status. – Only use the product if it is in an excellent technical status. – Observe the product labelling. – If cable connector the O-ring supplied is not necessary. 3 Function The sensor box SRGB detects the end position of the drive with the help of the SASF position indicator as an activating element. Inductive sensors of the sensor box detect the metallic actuating elements on the position indicator in a non-contact manner. These actuating elements are fixed at an offset of 90 ° and are suitable for anti-clockwise and clockwise drives with a 90 ° or 180 ° rotation angle. 4 Installation and commissioning Warning Electric voltage. Injury due to electric shock. � Switch off the power supply before opening the device. Note Installation and commissioning should only be conducted by qualified personnel. 4.1 Mechanical Mount the sensor box to the fastening interface of the semi-rotary drive. Use M5 mounting screws. The mounting holes in the sensor housing ensure that no adjustment is necessary when mounting the sensor. Attach the SASF position indicator to the drive shaft. Use M6 screws. Use a spacer disc, dependent on the wave height. When mount­ ing is complete, attach the stopper cap and identification stopper to the position indic­ ator. 1 2 3 4 1 Stopper cap 2 Identification stopper 3 Actuating elements 4 Spacer disc Fig. 2 4.2 Electrical Note Inappropriate cables or incorrect installation reduce the degree of protection of the sensor box. Note The product is suitable for industrial purposes only. This product can generate high frequency interference, which may make it necessary to implement interfer­ ence suppression measures in residential areas. Note Coupling powerful electromagnetic fields of 3 V can cause the product to mal­ function at an operating frequency between 500 and 600 kHz.

2. Screw the cable connector into the cable entry. Guide the electric connecting cable through the cable connector to the terminal block. – Conductor cross section: 1.5/2.5 mm2 (flexible/rigid). 3. Seal unused cable entries with blanking plugs. 4. Wire the connections (� product labelling). 5. Place the housing cover in position and tighten the 4 housing screws 2. Connection SRBG-C1-N-1-AS-M12-M12 / SRBG-…-M12 1 2 3 4 5 6 1 SRBG-…-M12-M12: Solenoid valve connection 2 SRBG-…-M12-M12:AS-i connection SRBG-…-M12: sensor connection 3 Yellow LED, witching status indication 4 Green LED, power supply indicator 5 Switching status indication 6 SRBG-…-M12-M12: Switching status indication for solenoid valve Programming instructions Adress 00 preset, can be changed via bus master or programming units IO code D Ident. code A ID1 code 7 ID2 code E Data bit Bit Function D0 Valve status / (0=valve off, 1=valve on) D1 Valve error1) / (0=wire break/short circuit; 1=no error) D2 Switching output sensor 12) / (0=attenuated; 1=uncushioned) D3 Switching output sensor 22) / (0=attenuated; 1=uncushioned) Parameter bit Bit Function P0 Watchdog (0=inactive; 1=active)3) P1 Switching element function sensor 24) / (0=N/O contact; 1= N/C contact) P2 Switching element function sensor 14) / (0=N/O contact; 1= N/C contact) P3 Not used 1) Check only with activated valve (D0=1) 2) Applies to N/C function (P2/P3=1; preset), reversed behaviour with N/O function (P2/P3=0) 3) Watchdog active: Valve voltage drops in the event of AS-Interface communication error 4) Presetting: N/C contact 5 Maintenance and care If used as intended, the product is maintenance-free. 6 Technical data Position indicator SASF SASF-S2-B-F-A34 SASF-S2-B-F-A56 Ring diameter [mm] � 65  110 Circlip height [mm] � 6  7 Ambient temperature [°C] -25 … 80 Mechanical data Shaft diameter [mm] � 58  90 Shaft height [mm] 20/30 30/50 Mounting hole pattern [mm] 30x80 30x130 Material Housing, Spacer disc, Identification stopper PBT Stopper cap PP Mounting screw, Actuating lug high-alloy stainless steel Hinweis The plastic housings of the position indicator are made of conductive material and must be integrated into a suitable earthing concept. Hinweis The position indicator SASF consists of conductive plastic material. � Use in potentially explosive areas possible, as there is no static charge. SRBG-…-M12-M12 Switching output AS-Interface Switching element function Programmable N/O contact/ N/C contact Max. switching frequency [Hz] 100 Idle current [mA]  35 Operating voltage range DC AS-Interface [V] 26.5 … 31.6 Load voltage range DC [V] 21.6 … 26.4 Current consumption with load voltage from AS-Interface and load voltage connection [mA]  100 Protocol AS-Interface specification V3.0 Required master spe­ cification ≥ V2.1 Slave type A/B slave Device-specific diagnostics Wire break/short circuit in valve Addressing range 1A … 31A (0) / 1B … 31B Reverse polarity protection for all electrical connections Sensor connection M12 x 1, plug, 4-pin Ambient temperature [°C] -25 … 70 Storage temperature [°C] -25 … 70 Degree of protection IP67 Shock resistance Shock test with severity level 2 to FN 942017-5 and EN 60068-2-27 Vibration resistance Transport application test with severity level 2 to FN 942017-4 and EN 60068-2-6 CE marking in accordance with EU EMC Directive Approval c UL us (OL) RCM compliance mark Housing PBT M12 plug, Screws high-alloy stainless steel Note on materials RoHS compliant / Contains paint-wetting impairment substances Mounting position any SRBG-…-M12/SRBG-…-C2 -P -ZU -ZC Switching output PNP non-contacting, 2-wire NAMUR Switching element function N/O contact N/O contact N/C contact Max. switching frequency [Hz] 500 500 3000 Operating voltage range [V DC] 10 … 30 6 … 60 8.2 Max. output current DC [mA] 100 100 3 Voltage drop [V]  3  6 - Idle current [mA]  25 - - Residual current [mA]  0.5  1 - Minimum load current [mA] - 4 - Reverse polarity protection for all electrical connections Switching status indication Yellow LED Power supply indicator Green LED - - Sensor connection SRBG-…-M12 M12 x 1, plug, 4-pin Electrical connection SRBG-…-C2 spring-loaded terminal Ambient temperature [°C] -25 … 70 -25 … 70 -25 … 100 Storage temperature [°C] -25 … 70 -25 … 70 -40 … 100 Degree of protection IP67 Shock resistance Shock test with severity level 2 to FN 942017-5 and EN 60068-2-27 Vibration resistance Transport application test with severity level 2 to FN 942017-4 and EN 60068-2-6 CE marking in accordance with EU EMC Directive � � in accordance with ATEX Approval c UL us (OL) RCM compliance mark Housing PBT M12 plug, Screws high-alloy stainless steel Note on materials RoHS compliant / Contains paint-wetting impairment sub­ stances Mounting position any