GLASCRAFT Probler Operation & User’s Manual

Not for use in explosive atmospheres. 90-110 psi (0.62-0.76 MPa, 6.2-7.6 bar) Air Inlet Pressure Range 3000 psi (20.7 MPa, 207 bar) Maximum Static Fluid Pressure USER MANUAL Important Safety Instructions Read all warnings and instructions in this manual. Save these instructions. ...

Section 1 Installation Warnings ............................................................................................................................................................ 3 Introduction ........................................................................................................................................................ 7 Standard Equipment ................................................................ ...

point symbol alerts you to a general warning and the hazard symbol refers to procedure-specific risk. Refer back to these warnings. Additional, product-specific warnings may be found throughout the body of this manual where applicable. 3 WARNING TOXIC FLUID OR FUMES HAZARD Toxic fluids or fumes can cause serious injury or death if s ...

Misuse can cause death or serious injury. Do not operate the unit when fatigued or under the influence of drugs or alcohol. • Do not exceed the maximum working pressure or temperature rating of the lowest rated system compo- • nent. See Technical Data in all equipment manuals. Use fluids and solvents that are compatible with equipment wetted parts. See Technical Data in all • equipment manuals. Read fluid and solvent m ...

potentially harmful mists, vapors, and atomized particulates. Read material manufacturer’s warnings and material MSDS to know specific hazards and precautions related to isocyanates. Prevent inhalation of isocyanate mists, vapors, and atomized particulates by providing sufficient ventila- tion in the work area. If sufficient ventilation is not available, a supplied-air respirator is requ ...

Separate CAUTION To prevent cross-contamination of the equipment’s wet- ted parts, never interchange component A (isocyanate) and component B (resin) parts. The gun is shipped with the A side on the left. The fluid manifold, fluid hous- ing, side seal assembly, check valve cartridge, and mix chamber are marked on the A side. Foam Resins with 245 fa Blowing Agents New foam blowing agents will froth at temperatures above 90°F (33 � ...

Introduction Before operating, maintaining or servicing any GlasCraft system, read and understand all of the technical and safety literature provided with GlasCraft products. If you do not have the proper or related manuals and safety literature for your GlasCraft system, contact your GlasCraft distributor. In this GlasCraft technical and safety publication, the following advisories will be ...

GCP1FX Round Probler Dispense Gun 313265 User Manual Section 1 - Installation: Standard Equipment ...

How The Gun Works The Probler Gun is used to spray or pour two- component, low viscosity polyurethane foam materials at outputs up to 60 pounds per minute. The gun features an air-assited full-finger trigger and a patented solvent-free automatic air-purge cleaning system. The trigger actuates a small valve in the gun handle that controls the flow of air into the piston ...

Assembly Instructions Refer to specific system user manual for complete system installation. See GCP1RX Gun illustration during instructions. 1. Connect whip hose to gun assembly. The swivel fittings on the whip hose assembly are sized differ- ently and will attach only one way. (Match like sized fittings.) Also connect the air hose assembly to ...

WARNING WARNING WARNING WARNING Refer to specific system user manuals for complete system installation. Pre operation Checklist Check that all fittings are tight and air regulators are turned to “zero pressure”. Do not place any part of the body in the path of the material spray. Do not point the gun at or near other personnel. ...

Initial Start-Up Procedure With all material and air lines connected, the gun is now ready for start-up. 1. Remove the side blocks on the front housing of the gun, by removing screws. 2. Place separate clean containers under each individual side block. Open manual material valves (black arrow forward, see Fig. 4 and Fig. 5) on each side block si ...

Spray Technique Always operate safely and follow all safety procedures outlined. To achieve the optimum spray pattern for each applica- tion, several mixing chambers are available. The standard mixing chamber supplied with your gun will be adequate for all but the smallest and largest applications. Foam rise and cure times will vary according to the material ...

Gun Handle Air Passage Locations and Thread Sizes 14 1/4 DRILL 1/8 DRILL 3/32 DRILL 19/64 DRILL NOTE: All fractional dimensions recorded in inches 3/4-16 UNF-2B (TAP) 1 -5/8-20 UN-2B (TAP) N DRILL 1/4-20 UNC-2B (TAP) #29 DRILL 8-32 UNC-2B (TAP) #29 DRILL 10-32 UNF-2B (TAP) #29 DRILL 10-32 UNF-2B (TAP) #29 DRILL 10-32 UNF-2B (TAP) 1/8 DRILL 8/32 UNC-2B (TAP) #29 DRILL ...

26 8 9 Mixing Chamber Assembly (see chart) 34 36 5 41 25 22 17c 15b 15d 15e 15f 15a 15c 17d 17b 17a (17) Air Switch Assembly (15) Piston Assembly 33 32 31 47 30 44 19 6 20 24 21 27 17 15 32 29 15 Round Spray Probler Gun 8 9 13 26 Service Kit GCP1R0 GC0114 GC2528 GC2540 GC2530 GC0166 GCP1R1 GC0114 GC2528 GC2540 GC2531 GC0167 GCP1R2 GC0114 GC2528 GC2540 GC2532 GC0167 GCP1R3 GC0114 GC2528 ...

1 40 35 45 11 12 10 16 5 22 14 13 46 39 5 37 38 22 18 43 23 2 Complete Filter Assembly available, GC0123 4 29 3 7 Complete Seal & Valve Kit available, GC0145 (00-03 only) 16 ...

List Ref. No. Part No. Description Qty. 1 117634 SWIVEL, UNION, NO #6 JIC 1 2 117635 SWIVEL, UNION 1 3 GC0061 RETAINER, RING 1 4 GC0101 SUPPORT, STRAINER 1 5 GC0102 HOUSING, CHAMBER, MIXING 1 6 GC0110 CAP, REAR, PROBLER, HG 1 7 GC2547 STRAINER, PROBLER H.G 1 8 CAP, AIR, PROBLER; see matrix table on parts illustration 1 9 SEAL, CHAMBER, MIXING; see matrix table on parts illustration ...

18 15c 13b 13d 27 24 37 30 45 23 34 33 32 31 51 48 17 18 6 22 19 15 13 28 33 20 5 35 25 42 43 26 13e 13f 13a 13c 15d 15b 15a (15) Air Switch Assembly (13) Piston Assembly Flat Spray Probler Gun 11 24 42 Service Kit GCP1F0 GC2540 GC2550 GC2332 GC0166 GCP1F1 GC2540 GC2551 GC2332 GC0167 GCP1F2 GC2540 GC2552 GC2332 GC0167 GCP1F3 GC2540 GC2553 GC2332 GC0167 GCP1F4 GC2541 GC2554 GC2333 GC0168 ...

19 12 49 20 5 46 38 16 47 21 39 1 44 36 9 10 8 14 5 20 50 2 4 30 3 7 40 11 Complete Filter Assembly available, GC0123 Complete Seal & Valve Kit available, GC0145 (00-03 only) ...

Ref. No. Part No. Description Qty. 1 117634 SWIVEL, UNION, NO #6 JIC 1 2 117635 SWIVEL, UNION 1 3 GC0061 RETAINER, RING 1 4 GC0101 SUPPORT, STRAINER 1 5 GC0102 HOUSING, CHAMBER, MIXING 1 6 GC0110 CAP, REAR, PROBLER 1 7 GC2547 STRAINER, PROBLER 1 8 GC2544 VALVE, BALL, CHECK, ASSY 2 9 GC2546 SPRING, COMPRESSION, 0.180 OD 2 10 GC2545 HOUSING, VALVE, CHECK 2 11 SEAL, VALVE, MIXING; ...