Harbor Freight Tools 92049 Assembly And Operating Instructions

TED - 12 VDC TED - 12 VDC TED - 12 VDC TED - 12 VDC ASSEMBLY AND OPERATING INSTRUCTIONS 3491 Mission Oaks Blvd., Camarillo, CA 93011 Visit our Web site at http://www.harborfreight.com Copyright © 2004 by Harbor Freight Tools®. All rights reserved. No portion of this manual or any artwork contained herein may be reproduced in any shape or form without the express written consent of Harbor Freight Tools. For technical questions and replacement parts, please call 1-800-444-3353 92049

D E S C R IP T IO N B o ttle C a p a c ity 3 2 flu id o u n ce s C u p C a p a city 1 2 flu id o u n ce s P o w e r C o n s u m p tio n 1 2 V D C fro m v e h ic le p o w e r s o c k e t P o w e r C o rd 5 fe e t, 1 8 A W G ca b le , v e h ic le c ig a re tte lig h te r a d a p te r p lu g W a rm in g T e m p e ra tu re 1 5 0 d e g re e s F , ± 1 0 d e g re e s F u s e 1 0 a m p fu s e in s id e a d a p te r p lu g B o ttle M a te ria l S ta in le ss s te e l O ve ra ll D im e n sio n s 1 1 .5 (H ) x 3 .7 5 (d ia .) in c h e s W e ig h t 2 lb s . (e m p ty) Save This Manual You will need the manual for the safety warnings and precautions, assembly instructions, and operating and maintenance procedures. Keep your invoice with this manual. Write the invoice number on the inside of the front cover. Keep the manual and invoice in a safe and dry place for future reference. Safety Warnings and Precautions Warning: When using this product, basic safety precautions should always be followed to reduce the risk of personal injury and damage to unit. Read all instructions before using this tool! 1. Disconnect power when not in use. 2. Do not drink directly from the heated Beverage Holder. 3. Do not overfill, tilt or shake immediately after filling with a hot beverage. 4. Do not touch the inside of the Beverage Holder when hot. 5. Do not connect the Beverage Holder power cord to a 12 VDC socket when cold beverages are contained. 6. Do not operate the Beverage Holder if the power cord or connector are damaged. 7. Do not submerge the Beverage Holder in water. 8. Do not expose the operating Beverage Holder to extreme, external heat. 9. Do not overtighten the Dispenser Cap or Cup. 10. Not intended for use by children.

power source. 12. Dairy and other beverages that spoil easily should not be contained for prolonged periods of time. 13. Close Dispenser Valve and secure the stainless steel Cup when beverages are contained. 14. Before using this product, any part that appears damaged should be carefully checked to determine that it will operate properly. Any part that is damaged should be properly repaired or replaced by a qualified technician. Note: Performance of this product may vary depending on variations in vehicle bat- tery power. Warning: The warnings, cautions, and instructions discussed in this instruc- tion manual cannot cover all possible conditions and situations that may oc- cur. It must be understood by the operator that common sense and caution are factors which cannot be built into this product, but must be supplied by the operator. Unpacking When unpacking, check to make sure the following parts are included. If any parts are missing or broken, please call Harbor Freight Tools at the number on the cover of this manual. Cup Beverage Container Dispenser Valve Cap Handle Carrying Strap Fused Plug 12 VDC Power Cord

the interior of the container with mild soap and warm water. Wash the Cup. Rinse well. Refer to the photos on the previous page. Caution: Do not place unit in a bath of water. This may damage the electrical components of the unit. 2. Fill the Beverage Holder with the desired drink or liquid food. 3. Screw in (clockwise) the Dispenser Valve Cap. 4. Plug one end of the Power Cord into the bottom of the Beverage Container and the Fused Plug into a 12 VDC vehicle power socket. This will heat up the contents and keep it warm. When the Power Cord is unplugged, the contents will keep warm for a period of time. Note: If the stored drink is to be kept cool, do not plug in the Power Cord. 5. To pour a drink from the Beverage Holder, press in on the Dispenser Valve Cap until it locks in the down position, then pour. If the contents are of a thick consistency (such as soup), unscrew the Dispenser Valve Cap and pour out the contents. 6. Replace the Dispenser Valve Cap and press in on the cap button to lock. 7. Wash container after each use. 8. Store unit with Power Cord in the factory box when not in use. Maintenance / Cleaning 1. This product has no replaceable parts. 2. After each use, place warm water and mild soap inside the Beverage Holder to clean. Do not submerge unit into water. 3. If the unit does not warm up, the 10A fuse in the Fused Plug may need replacement. Unscrew the plug cap to view and replace fuse. If the fuse is good, the unit is not receiving power, or it is defective and needs servicing by a qualified technician.