Innometriks Cheetah SE Quick Start Manual

Quick Start Guide 8200-1558-01 REVISION B0 APRIL 2018 Overview This guide provides quick start installation and connection information for the Cheetah SE Reader models. The reader is configured using the web browser. See Browser Based Administration on Page 12. Default or configured settings can be displayed using the keypad. See Keypad Operation on Page 11. NOTE Details on reader configuration, administration and general func ...

■ Compact design ■ Smart card authentication - contactless or contact reader models • HID SE module contactless Smart Reader — Carrier frequency of the RF interface: 13.56 MHz. — Supported card formats: iClass, PIV, PIV-I, CAC, TWIC, MIFARE, DESFire, EV1, EV2, smart card CSN, HID SEOS. • Microchip SEC1210 Smart Card Reader (contact) & HID SE module (con ...

• Includes support for updating reader firmware through a web browser. • Provides for saving or uploading the reader configuration to/from a file. ■ PACS / Reader formations - single reader, star, daisy chain NOTE • The configuration file contains all independent reader settings such as Normal and Secure mode settings, card support configuration, and reader communication options ...

The Cheetah SE Reader requires nominally 12 VDC at 1 Amp to operate correctly. The power source can be from the power supply on the PACS or can be a separate local supply. The reader must be powered by a compatible UL listed access control panel or a UL294 listed power supply. CAUTION: If you are using a separate local power supply, ensure that the ground of the local supply connects to the ground of the PACS. The local power su ...

screwdriver, wire strippers. Mounting Plate Figure 3 on Page 5 shows front and back views of the mounting plate for the Cheetah SE readers. Figure 3:  Mounting Plate Front and Back Views Installation Instructions To remove the mounting plate from the reader housing: 1. The mounting plate is delivered connected to the reader h ...

Figure 4:  Mounting Plate with Outdoor Gaskets 1. Insert the perimeter gasket to the front of the mounting plate and attach the wall gasket to the rear of the mounting plate (both gaskets supplied loose in the Outdoor Install Kit). See Figure 4 on Page 6. To secure the mounting plate to a support: Figure 2 on Page 4 shows the dimensions of the mounting plate (matches the back plate of the ...

To attach the reader housing to the mounting plate: 2. Affix the reader housing to the secured mounting plate. 3. Secure the reader housing to the mounting plate using proper ESD procedures by inserting screws (supplied) into the two seats at the bottom of the reader. The type of screws should be 2802-8531-19 Screw 4-40 UNC x 1/2" CSK Socket 4. Apply power to the reader. Figure 8:  Cheetah SE Reader Rear ...

Pin # Pin Name Properties Wiring 1 GND Chassis Ground Chassis Ground that should be connected to Earth Ground by a low impedance path 2 PowerIN_N Power Negative line From negative terminal of power source 3 PowerIN_P Power Positive line From positive terminal of power source 4 5Vdc 5 VDC outputs at 0.5 amps Optional 5Vdc to external connector 5 RS485-A EIA-485 differential line 1: '+', TxD- /RxD-, or inverting p ...

30 VDC 1 A 5 V Output (two connections provided) 5 V 0.5 A (combined maximum) Optical Relay (wet) 5 V 0.05 A Table 7:  Circuits Wiring Diagrams Wiring for FICAM/OSDP Connectivity Figure 9 on Page 9 shows an example of FICAM/OSDP wiring. Figure 11 on Page 10 shows wiring for supervised inputs. Figure 9:  FICAM/OSDP Wiring Wiring for RM Connectivity Figure 10 on Pa ...

Wiring Supervised Inputs Figure 11 on Page 10 shows examples of wiring normally closed (NC) and normally open (NO) supervised inputs. The pin numbers refer to the 9-pin Molex connectors (J7) shown in Figure 9 on Page 9 and Figure 10 on Page 10. Figure 11:  Examples of Supervised Inputs Setting Up the Reader The default or configured settings for the reader are shown in the reader LCD display. All settings can be changed through ...

Keys Status Screen Display 1. Press function keys F1 and F4 at same time to display the Status Screen. Pressing 1 will redisplay the current firmware version. 2. Press key 2 to display the reader's current IP address. 3. Press key 3 to display Ethernet Status. 4. Press key 4 to display the current Reader Address. 5. Press key 5 to display the current Reader Baud Rate. 6. Key 6 is not used. 7. Press key 7 to ...

8. Press key 8 to display Supervised Inputs. Keys 9 and 0 are not used. Press # to exist the status menu. To Configure Reader Brightness 1. Press keys F2 and F4 simultaneously to display screen contrast setting. Sample text displays on line one; control keys display on line two. a. Use the F2 (for +) or F3 (for -) keys to increase or decrease the display contrast. Default Factory Settings ■ Reader starts by reading a default ...

All readers ship with unprotected access to Administration Mode. The default administrator user name is "admin" and the default password is "password". Additional administrators should be created and the password for the initial administrator should be changed for security purposes. From a web browser, connect to the reader's IP Address. The login screen displays. Figure 12:  Login screen Enter the administrator user name and ...

Click on Save Profile to restart the reader with the changed profile parameters. Upon the reader restarting, log back in as administrator. Select Network from the main screen. Depending on the reader's setting for Static IP address or DHCP, a screen similar to one of the following is displayed: Figure 14:   Ethernet Screens If you make change ...

reader with the changed password, select Update Settings. To update reader firmware, select UPDATE and supply the location of a new firmware file. Click the Upload File button to upload the file to the reader and update the firmware. The reader will then restart. To display options to download, upload or restore a configuration file, select CONFIGU ...

Innometriks Inc. 6 Technology Park Drive Westford, MA 01886 http://www.innometriksinc.com Email: [email protected] Phone: 760-542-0200 Use your FTP client and provided credentials to access the ftp.innometriks.com site to download the puchased applications and documentation. Additional Information Canadian Radio Emissions Requirements The digital apparatus does not exceed the Class A limits ...