KeepGuard KG Series Instruction Book

equipped with built-in infrared LEDs, so that it can be triggered by any movement in a location, then take high quality pictures or video clips. Please refer to the notes below and instructions in this manual to ensure that you are completely satisfied with this product. Highly Recommended by Outdoor Explorers - KeepGuard Wildlife Scouting Cam KG Cams Instruction Book Contents Quick Start 2 Notes before use 2 Camera Overview 3~4 Operation Part 4 Accessories 4 Power Supply 5 SD Card 5 Operational Modes 6 Settings 7~11 Mounting and Positioning 12 Specification 13 Warranty Card 14 KEEPTIME Applicable models：KG691, KG762, KG785

→ Load 8 lithium AA or alkaline AA batteries → Insert the SD card → Switch to the SETUP Mode → Press MENU button → Press UP or DOWN key to select Camera or Video Mode → Put it good position → Switch to the ON Mode and it have started working. ● Be sure the camera′s power is switched OFF before inserting or removing SD cards or batteries. ● Check to make sure you have used new alkaline or lithium batteries. We recommends using a full set of 8 Energizer R Lithium AA batteries to obtain maximum battery life. ● Batteries or DC power supply inserted/connected with correct polarity and the power level is sufficient. ● SD card have sufficient available space and is its write-protection (lock) switch off. ● Always move the power switch from OFF to SETUP mode. It is possible that the camera could lock up if it is switched from ON to SETUP mode. If this occurs, please move the switch to OFF and then push it up to SETUP again. Quick Start Notes Before Use 2 KEEPTIME

「Microphones」 KEEPTIME

KEEPTIME

you will see that it has 8 battery slots. For maximum battery life, we recommend using 8 lithium AA or alkaline AA batteries. The cam may also be operated by just four batteries installed in the first slots only (starting on the right-see photo). Battery life will be shorter with 4 batteries, but the camera will operate normally. Whether you use 4 or a full set, be sure to insert each battery with correct polarity (negative or “flat” end against the long spring of each battery slot). Power Supply SD Card Insert the SD card ( OFF mode ) before beginning to operate the camera. SD card is supported up to maximum 32GB capacity. 32GB 5 KEEPTIME

switch to the SETUP position will turn on the LCD display and you will see an information screen. Operational Modes The cam has three basic operational modes: 「OFF」, 「ON」 and 「SETUP」 ●「OFF 」Mode When cam in OFF mode, you can do the following: • replacing the SD card or batteries • connecting cam with other device by USB port It will occur a little of power consumption under OFF mode. If you won't use it for a long time, please take batteries off. ●「ON」Mode Once in ON mode no manual controls are needed or possible (the control keys have no effect). The cam will take photos or videos automatically (according to its current parameter settings) when it is triggered by the PIR sensor′s detection of activity in the area it covers. T T 3M 720P 0000/0888 Camera Mode Time Stamp ON Time Scan ON SD Card Battery Level Video Mode Image Resolution of Photos Taken Audio Rec ON Video Resolution Available Video Recording Time KEEPTIME

and LEFT/RIGHT keys ( to move to the next field ) to set the hour ( 24-hr format only, “00”=midnight,“12”=noon) and minute, and then (on the lower row ),the year,month and date. Once all settings are made, press OK to save. Dual Camera Selects whether still photos or video clips are captured when the camera is triggered. “Dual”=Camera+Video Set Exit Image Size OK 8M MENU 16M 3M Selects resolution for still photos from 3 to 16 megapixels. Higher resolution produces better quality photos, but creates larger files that take up more of the SD card capacity. 7 KEEPTIME

in Camera mode. This setting affects photos taken in Field Scan mode as well. 640*360 Selects video resolution (in pixels per frame). Higher resolution produces better quality videos, but creates larger files that take up more of the SD card capacity (fills up faster). Video Length Sets length per captured video clip. Settings begin with 10 second default when parameter is first selected. After stepping down to 5s, video length settings start over at 60s. 10s 8 Set Exit OK MENU KEEPTIME

for ID purposes when multiple cameras are setup, since each camera will imprint its name on all photos (but not videos) it captures. Selects the length of time that the camera will “wait”until it responds to any additional triggers from the PIR after an animal is first detected and remains within the sensor's range. During this user set“ignore triggers”interval, the camera will not capture photos/videos.This prevents the card from filling up with too many redundant images. Set Exit Coordinate Input OK OFF MENU ON Using the Setup Menu Input Screens"Allows user to input latitude and longitude coordinates for camera's location.This data will be embedded in files saved on camera’s SD card. 10s KEEPTIME

Time Scan Set Exit Time Period Set OK MENU Set Exit Time Scan OK MENU Press OK and use UP/DOWN keys ( to change the setting ) and LEFT/RIGHT keys ( to move to the next field ) to set time. Once all settings are made, press OK to save. Note: two time blocks can not appear overlap section, or you will not set it successfully. For example: A 8:00-12:00 B 13:00-23:00, this is OK for set. Time Scan (Time Lapse) recording mode on/off. When activated, Time Scan forces the camera to take photos or videos even when it is not triggered by an nearby live animal,useful for constant monitoring of an area that might be far away from the camera. The user can set start and stop times for up to two in dependent “blocks”of Time Scan recording,as well as the interval time between each photo/video OFF ON OFF ON Language Set Exit Language OK English MENU Selects user's preferred language from all nine languages. 10 KEEPTIME

Default Settings Set Exit Version OK MENU Set Exit Format SD Card OK Execute MENU Select“Execute”and press OK to restore all parameters to the original factory default settings. Set Exit Default Settings OK MENU Deletes (erases) all files stored on a card to prepare it for reuse. Always format a card that has been previously used in other devices. Caution! Make sure you have downloaded and backed up any files you want to preserve first! Press OK to execute, press MENU (or select NO then press OK) to exit without formatting. Execute KG762 160830A KEEPTIME

Mounting We recommend mounting cam on a sturdy tree with a diameter of about 6 in. (15cm). To get the optimal picture quality, the tree should be about 16-17 ft(5 meters) away from the place to be monitored, with the camera placed at a height of 5-6.5 ft. (1.5~2 m). Also, keep in mind that you will get the best results at night when the subject is within the ideal flash range, no farther than 60' (19m) and no closer than 10'(3m) from the camera. There are two ways to mount cam: using the provided adjustable web belt, or the tripod socket. •Using the adjustable web belt: Push one end of the belt through the two brackets on the back of cam. Thread the end of the strap through the buckle. Fasten the belt securely around the tree trunk by pulling the end of the strap firmly so there is no slack left. •Using the tripod socket:The camera is equipped with a socket at the bottom end. Sensing Angle and Distance Test To test whether cam can effectively monitor the area you choose, this test is recommended to check the sensing angle and monitoring distance of cam. To perform the test: •Switch cam to SETUP mode. • Make movements in front of the camera at several positions within the area where you expect game or subjects to be. Try different distances and angles from camera. • If emotion indicator LED light blinks, it indicates that position can be sensed. The results of your testing will help you find the best place where mounting and aiming the cam. The height from the ground for placing the device should vary with animal size appropriately. In general,3 to 6 feet is preferred. You can avoid potential false triggers due to temperature and motion disturbances in front of the camera by not aiming it at a heat source or nearby tree branches or brush (especially on windy days). KEEPTIME

Camera; Video; Dual Image Size 3MP;8MP;12MP 3MP;8MP;16MP 3MP;8MP;16MP Capture Number 1-3 1-9 1-9 Video Size 640x360; 1280x720; 640x360; 1280x720; 640x360; 1280x720; 1920x1080; Video Length 5s-60s 5s-60s 5s-60s Camera Name Input Input Input Interval 1s-60m 0.6s,1s-60m 1s-60m Coordinate Input ON; OFF ON; OFF ON; OFF Time Stamp Hidden and on Hidden and on Hidden and on Time Period ON; OFF ON; OFF ON; OFF Timed Scan 2X 2X 2X Video Sound Hidden and On Hidden and On Hidden and On Format Execute Execute Execute Default Set Execute Execute Execute Language English English, Français, Español, Deutsch, Italiano, Pусский, Subcontinental, 繁體中文, 简体中文 English, Français, Español, Deutsch, Italiano, Pусский, Subcontinental, 繁體中文, 简体中文 KEEPTIME

Your Name Your Add Your Tel Warranty State During warranty, hardware failure occurring, which caused by product itself, we will provide free maintenance service for the customer. Free warranty is for the first year. If there is a need for repair, you should offer this warranty card, please take care of this card. KEEPTIME