HP J1530C Installation Instructions Manual

rp74xx/rx76xx/SEU Servers Installation Instructions Kit contents WARNING: Do not mount this rack integration kit in a rack with sectional columns, such as the HP 5642 rack. If any of the following items are missing or damaged, contact your HP authorized reseller. The following hardware pieces are included in this kit. Quantity Description Picture 1 Cable management arm (5069-6366) 1 Slide, left (A6434-04045) 1 Slide, right (A6434-0 ...

(0535-0076) B 18 M5 x 16-mm screw (0515-3019) C 6 M4 x 6-mm screw (0515-4500) D 18 M5 barrel nut (0590-2318) E 2 10–24 custom nut (A6093-00180) F 2 M4 x 10-mm flat- head screw (0515-4499) J 3 M4 x 8-mm screw (0515-0433) H 18 M5 cage nut (353039-002) Required tools • T-20 Torx driver • T-25 Torx driver • 8-mm hex-nut driver Rack warning WARNING: To reduce the risk of ...

hole racks 1. Attach barrel nuts to the front columns. Item Reference 1 Product outline 2 Positions for mounting the product (refer to step 8) 3 Positions for mounting the front of the slides (refer to step 3) 2. Attach barrel nuts to the rear columns. Item Reference 1 Product outline 2 Positions for mounting the cable management arm (refer to step 7) 3 Positions for mo ...

3. Install the right and left slides into the rack. 4. Choose one of the following options: o If you have a lift kit, place the server on the slides, and then go to step 6. o If you do not have a lift kit, then go to step 5. WARNING: The weight of this product requires a lift to install. If a lift is not available, go to step 5 for installation of lift handle panels. If lift handles are already installed, continu ...

7. Install the cable management arm. a. Attach screws (B) to the left rear column. b. Slip the cable management arm over the screws (B) and tighten. c. Extend the cable management arm to the left rear side of the product. d. Attach the cable management arm to the studs, and secure it with nuts (E). 8. Install the bezel front. 9. Install the interlock device. NOTE: If the rack is bolted to the floor or is used in a rack ...

3 First product 10. Install the rods as shown in the following figure. Installing servers into square- hole racks 1. Attach cage nuts (H) to the front columns. Item Reference 1 Product outline 2 Positions for mounting the product (refer to step 9) 3 Positions for mounting the front of the slides (refer to step 4) ...

Item Reference 1 Product outline 2 Positions for mounting the cable management arm (refer to step 8) 3 Positions for mounting the rear of the slides (refer to step 4) 3. Adjust the slides according to the guidelines in the following table. Item Measurements required for rack 1 465 mm (18.31 in) Item Measurements required for rack 2 476.2 mm (18.75 in) 3 711 to 774.7 mm (28 to 30.5 in) 4. Install the right and le ...

o If you have a lift kit, place the server on the slides, and then go to step 7. o If you do not have a lift kit, then go to step 6. WARNING: The weight of this product requires a lift to install. If a lift is not available, go to step 6 for installation of lift handle panels. If lift handles are already installed, continue to step 7. CAUTION: This server must be unpacked in an ESD safe environment. Observe all E ...

8. Install the cable management arm. a. Attach screws (B) to the left rear column. b. Slip the cable management arm over the screws (B) and tighten. c. Extend the cable management arm to the left rear side of the product. d. Attach the cable management arm to the studs, and secure it with nuts (E). ...

10. Install the interlock device. NOTE: If the rack is bolted to the floor or is used in a rack configuration with at least four bayed racks, then the interlock device is not necessary. If two products are installed and the rack depth is no more than 717.55 mm (28.25 in), the interlock device can be installed so that you can remove one product at a time. NOTE: The products must be racked adjacent to each other to use the inter ...

racks NOTE: The SEU can only be used with the rp84XX and rx86XX server. Item Reference 1 SEU 2 Server 1. Attach barrel nuts (D) to the front columns. Item Reference 1 SEU outline 2 Positions for mounting the product (refer to step 6) 3 Positions for mounting the front of the slides (refer to step 3) 4 Server ...

Item Reference 1 SEU outline 2 Positions for mounting the cable management arm (refer to step 7) 3 Positions for mounting the rear of the slides (refer to step 3) 4 Server 3. Install the right and left slides into the rack. Do not tighten the outer screws. 4. Remove and discard the center screw, allowing the slide to lower slightly, and then tighten the outer screws. 5. Place the server on the slides using a l ...

safe environment. Observe all ESD safety precautions before attempting this procedure. Failure to follow ESD safety precautions can result in damage to the server. 6. Insert screws to secure the server to the slides. NOTE: Use the handles only to adjust the position of the server while it is on the slides. Do not use the handles to lift the server. 7. Install the cable management arm. a. Attach screws (B) t ...

9. Install the interlock device. NOTE: The interlock device is required for each rp84XX and rx86XX and SEU pair installed. NOTE: The products must be racked adjacent to each other to use the interlock device. NOTE: If two pairs are installed, two interlock devices are needed, with one connected to the bottom pair and the other connected to the top pair. Item Reference 1 SEU 2 First mounting holes for SEU 3 Server 10. Install ...

bottom actuator bracket. If the clearance is less than 1 mm (0.04 in), then proceed to step 12. If the clearance is greater than 1 mm (0.04 in), then proceed to step 13. 12. Push the actuator bracket down while tightening the screw. 13. Verify the clearance again. If necessary, readjust, and then go to step 12. Installing SEU into square-hole racks 1. Attach cage nuts (H) to the front columns. Item Refe ...

Item Reference 1 SEU outline 2 Positions for mounting the cable management arm (refer to step 8) 3 Positions for mounting the rear of the slides (refer to step 4) 4 Server 3. Adjust the slides. Item Measurements required for rack 1 465 mm (18.31 in) Item Measurements required for rack 2 476.2 mm (18.75 in) 3 711 to 774.7 mm (28 to 30.5 in) 4. Install the right and left slides into the rack. Do not tighten the ou ...

to lower slightly, and then tighten the outer screws. 6. Place the server on the slides using a lift kit. WARNING: The weight of this product requires a lift to install. Do not manually lift the server to install it. Use a lift that can handle the load of your server. CAUTION: This server must be unpacked in an ESD safe environment. Observe all ESD safety precautions before attempting this proc ...

10. Install the long and short rod. Item Reference 1 SEU box 2 First mounting holes for SEU 3 Server 11. Install the rods. 12. Check the clearance between the short rod and the bottom actuator bracket. If the clearance is less than 1 mm (0.04 in), then proceed to step 13. If the clearance is greater than 1 mm (0.04 in), then proceed to step 14. ...

screw. 14. Verify the clearance again. If necessary, readjust, and then go to step 13. ...