LIW BAFFIN TRIO Manual 

FROM A DIRECT REPRESENTATIVE OF LIW CARE TECHNOLOGY, OR IN SPECIALIZED MEDICAL SHOP REPRESENTING LIW CARE TECHNOLOGY IN POLAND. NOTE! USE ONLY INDOOR WITH NO THRESHOLDS. NOTE! WHEN USING THE PRODUCT, IT SERVICE, MECHANISMS SUBMITTING AND REGULATING, IT MAY OCCUR DANGER OF ENTRAPMENT AND/OR COMPRESSION OF USER’S/ACCOMPANYING PERSON BODY IN HOLES/SLOTS BETWEEN THE ELEMENTS. IT IS AD ...

2. Warnings & Safety Information ........................................................................................................ 4 3. Technical Information ...................................................................................................................... 5 3.1 Technical Speci ...

new approach in rehabilitation. Every effort has been made to ensure that BAFFIN TRIO Multifunctional device is extremely easy to use, as well as providing a wide range of anatomical adjustment and posture correction. Please ensure this manual is read thoroughly before use. It is important to follow all the guidelines ...

The BAFFIN TRIO Multifunctional device consists of1: 1. Central Core (Spine) 13. Actuators 2. Back Support 14. Push Handle 3. Side supports 15. Brakes 4. Hip Supports 16. Head rest 5. Legs abduction belts 17. Heel Supports 6. Thigh supports 18. Table 7. Armrests 19. Battery 8. Knee Support 20. Respirator Shelf 9. Footrest 21. Spine Interlock 10. Foot Platform 11. Standing Base 12. Seat Fig. 1: Frame Work Of Multifunctional device ...

There are two sizes of an individual standing seat available. Detailed size parameters are presented in the table below: Size I (cm) Size II (cm) 1 Seat height (SH) 62 62 2 Back height (BH) 61 77 3 Backrest Angle (BA) 800 ÷ 1150 800 ÷ 1150 4 Verticalization Range (VR) 00 ÷ 850 00 ÷ 850 5 Base length (BL) 106 112 6 Base width (BW) 69 77 7 Foot platform height (FH) 32÷42 35÷49 8 Foot platform length (FL) 28 32 9 Rear wh ...

The BAFFIN TRIO Multifunctional device allows the user to be repositioned from sitting, to laying or standing, via an actuator control pad. It is primarily for indoor use only. It is not suitable for manoeuvring kerbs. It is not intended for transport, therefore the user should not be transported in the Baffin TRIO in a vehicle. Intended Users are those with faulty postures and muscle dysfunction. Particular conditions include cerebral pa ...

The knobs are situated on the left and right sides of the device. They operate independently. It allows symmetrical and asymmetrical position of the user's body. To adjust the spacing between the thigh supports, use the two knobs which are situated under the thigh supports (Fig. 4). In order to adjust the supports, unfasten the upholstery from the thigh supports and fold it to uncover the knobs on the underside of ...

Before adjusting the depth of the seat, remove the plastic cover on both sides of the machine. The covers are fixed with the use of 4 screws (2 on each side), placed on the top and bottom covers (Fig. 6). Fig. 6: Screws fixing the covers After undoing the screws, pull out the covers from the fixing slits (Fig. 8). In order to prevent damage to the covers, first take off the back cover (outer), then the front cover (inne ...

To adjust the depth of the seat, use the blocking screws marked with the red arrows (Fig. 9). It is possible to change the depth of the device after the screws have been completely undone on both sides of the device. Push in or pull out the back part of the seat into the right depth. The depth of the seat must be set so that the axis of the device (marked with X and Y in the figure) are congruent with the anatomical axis of the hip ...

5.4.1 Lateral Supports Width Adjustment In order to adjust the width and height of the lateral supports, unscrew the knob marked with a red arrow in Figure 11. After adjusting the width and height of the lateral supports, tighten the knob. Fig. 11: Lateral Supports Width and Height Adjustment Carefully check if the adjustment is completely correct:-i.e. � That no element of the equipment puts too much pressure on any ...

The Armrest system makes it possible to smoothly adjust the angle, the height and the spacing of armrests. In order to change the angle of armrests, loosen the blocking knobs (Fig. 13), and then, after setting the right angle, block the mechanism of armrests by tightening. Fig. 13: Adjusting the angle of armrests Spacing of armrests is adjusted by switching the armrests. In order to switch them to opposite sides, pull away settin ...

The footrest is used to support the feet while sitting, lying down and during tilting. The footrest is adjustable by: - height, - angular positioning of the foot platforms. 5.6.1 Adjusting the Height of the Footrest Inappropriately tightened knobs and screws can cause the footrest to move in the upright position and can lead to injury or damage to the device. Use the knob marked with a red arrow in Figure 15., to adjust the heig ...

For safe handling of the BAFFIN TRIO Multifunctional device, it is necessary to fasten the user’s feet onto the foot platform. Fastening the feet is carried out with the help of four straps. Unfasten the strap buckles, place feet on the platform, adjust the straps so that they lie tightly close against the feet. Finally, secure the buckles (Fig. 17). Fig. 17: Fastening the feet onto the foot platform 5.7 ...

the user's knee. After setting the right distance from the user's knee (i.e. the minimum space between the user's knee and the knee support which does not cause discomfort), block the knee support with the knob. Properly set, the knee support should not put too much pressure on the leg in the sitting and standing position. Each ti ...

5.9 Fitting and adjustment of the vest and hip belts The vest and hip belts are used to secure the correct position of the user in the seat. The vest and the hip belts are attached to the device with the use of belts. To fix the vest correctly, pass the fastening belts through the holes in fastening loops. These loops can be found in the top part of the back support (Fig. 21) and ...

The Baffin Trio is equipped with a remote control to easily change the seat’s position. The user can be put into the standing position from a sitting or a lying position. The user cannot be put into upright position until all the adjustment procedures are completed. SEE Section 5 above. Check that all the adjusting and fixing screws are properly tightened. Ensure the following action is taken ...

Push the button on the remote control which is marked with the blue arrow (Fig. 25) – the back support will start to recline/ bend down and the footrests will start moving up. Keep pushing the button on the remote control until the device is in laying position. The activity can be stopped any time to obtain various positions. In order to return to the sitting position, push the button on the remote contro ...

adjustment might cause the table to be unstable, damage the device or risk an injury to the user. 7.2.1 Adjusting the width of table handles In order to adjust the width of the table brackets to the spacing of the armrest, loosen the screws on the table holders (shown in Fig. 27, red arrows), then slide or enlarge the table holders ...

- the diode is orange, constant, short light impulses with the 1s frequency – charging - the diode is green, monotonous light – the charging is finished, and the battery is full. Low battery status is indicating by repetetive, short sound signals – which are reminder for pluging the device into the network 100 – 240V to charge the battery again. Appearance of the first sound ...