Semtech EB-GS2971 Operation & User’s Manual

Text of Semtech EB-GS2971 Operation & User’s Manual

Evaluation Board User Guide

1 of 22 Proprietary & Confidential GS2971 EB-GS2971 Evaluation Board User Guide 52169 - 2 June 2012 www.semtech.com

Evaluation Board User Guide

52169 - 2 June 2012 2 of 22 Proprietary & Confidential Contents Overview ..............................................................................................................................................................3 1. Evaluation Board User Guide....................................................................................................................4 1.1 Power ...............................

Evaluation Board User Guide

52169 - 2 June 2012 3 of 22 Proprietary & Confidential Overview Together with the EB-GS2971 Evaluation Board, this document serves as a guide for evaluating the GS2971; a Gennum 3Gb/s, HD, SD SDI Receiver, with integrated equalizer. This document contains four main sections: 1. Evaluation Board User Guide. 2. Evaluation Board Schematics. 3. Evaluation Board Layout. 4. Evaluation Board Bill of Materials The figure below

Evaluation Board User Guide

52169 - 2 June 2012 4 of 22 Proprietary & Confidential 1. Evaluation Board User Guide Figure 1-1 shows the inputs, outputs and power connections for the EB-GS2971. Figure 1-1: GS2971 Evaluation Board (EB-GS2971) SDI Input (J4) SDI Loop-Through (J5) CD O/P Jumper (JP4) AES Audio Outputs (J19 - J 22) Parallel Video Output (J16) GSPI (J18) H, V & F Timing Signals (J17) 1.8V/3.3V Jumper (JP7) Power (J24) Power (J100) Power

Evaluation Board User Guide

52169 - 2 June 2012 5 of 22 Proprietary & Confidential 1.1 Power The EB-GS2971 requires a single +5V DC power supply. The board can be powered through either J24 or J100. Additionally, the board can powered through J18 from an EB-GS2972 or FPGA board. Figure 1-2: Power Supply Switch SW100 allows the user to select three different voltages: 5V Ext, 5V EB and 3.3V FPGA. It is important to note that if you are interfacing

Evaluation Board User Guide

52169 - 2 June 2012 6 of 22 Proprietary & Confidential 1.2 SDI Input (J4) The EB-GS2971 includes a single SDI input. 1.3 Switch Settings (SW2) A DIP switch (SW2) is populated on the EB-GS2971, with each bit labelled on the silk-screen. This switch is used to set the operating modes of the GS2971. The signal can be set HIGH by placing the switch to the ‘1’ position (Closed). NOTE: Some signals are active LOW, so you

Evaluation Board User Guide

52169 - 2 June 2012 7 of 22 Proprietary & Confidential 1.4 Outputs 1.4.1 SDI Loop-Through (J5) A relocked or non-relocked buffered version of the input stream is available on the serial loop-through output (J5). It is designed to be SMPTE compliant for voltage level, rise/fall time and return loss at three rates (SD, HD and 3G) using the compensation network. The GS2978 Cable Driver is necessary to guarantee return los

Evaluation Board User Guide

52169 - 2 June 2012 8 of 22 Proprietary & Confidential 1.5 JTAG/GSPI Header (JP1) The GS2971 contains a set of internal status and configuration registers. These registers are available to the host via the GS2971’s GSPI pins. Access to the applicable pins on the GS2971 is provided using the JTAG/GSPI header. A GSPI dongle is provided for communication to the GSPI interface. If you have the EB-GS2971 and an EB-GS2972

Evaluation Board User Guide

52169 - 2 June 2012 9 of 22 Proprietary & Confidential 2. Schematics 2.1 Top Level Schematic Figure 2-1: Top Level Schematic GND GND S1 B3S-1002P RESET GND GND PCLK MALE: TOP-SIDE MALE: TOP-SIDE 2 4 6 8 10 12 14 16 18 20 22 24 26 28 30 32 34 36 38 40 42 44 46 48 1 3 5 7 9 11 13 15 17 19 21 23 25 27 29 31 33 35 37 39 41 43 45 47 J16 TMMH-124-01-F-D-RA-ES 2 4 6 8 10 1 3 5 7 9 J17 TMMH-105-01-F-D-RA R84 1.15K H HVF0 F HVF

Evaluation Board User Guide

52169 - 2 June 2012 10 of 22 Proprietary & Confidential 2.2 Cable Driver Schematic Figure 2-2: Cable Driver Schematic R41 75R R92 10K R43 75R C48 10n 75-ohm traces A_GND C52 4u7 JP4 R48 49R9 R49 49R9 C57 10n SDI 1 SDI 2 NC 5 GND 3 DISABLE 6 NC 14 SD/HD 10 TAB NC 8 SDO 11 SDO 12 NC 15 NC 13 NC 7 RSET 4 VCC 9 NC 16 U7 GS2978 A_GND C50 4u7 SD closed HD open A_GND LOOP-THROUGH L4 5n6 R47 75R R40 750R +3.3V R44 75R C47 10n

Semtech Motherboard Owners Instructions: