Molbio Trueprep AUTO Operation & User’s Manual

Sample Prep Device all-guides com ...

Table of Contents Table of Figures 1 2 1 Introduction 3 2 Installation 4 2.1 Installation Precautions 4 2.2 Environmental Requirements 4 3 Specifications 4 4 Precautions 4 5 Materials Required 5 5.1 Contents 5 5.2 Materials Required but not provided with device 5 6 The Trueprep™ AUTO 5 6.1 A Top Panel View 5 6.1B Back Panel View 6 6.2 The Cartridge 6 7 Using the Trueprep™ AUTO 7 7.1 Charging/Using the Truepre ...

Figure 1: The Trueprep™ AUTO Top View, with cartridge holder 5 shown in the front panel Figure 2: The Trueprep™ AUTO Back Panel, with tubing and caps for plugging 6 in reagent bottles from the Reagent Pack of the Trueprep™ AUTO Universal Cartridge Based Sample Prep Kit Figure 3: Disposable Trueprep™ AUTO cartridge for sample processing 6 Figure 4: Low battery LED glowing red 7 Figure 5: The Charging Por ...

Testing for infectious diseases by detecting the pathogens nucleic acids using nucleic acid amplification methods is a highly specific and sensitive diagnostic tool. Molbio's Truelab™ micro PCR System is a nucleic acid amplification platform that works on Real Time Polymerase Chain Reaction (PCR) technology that enables near patient diagnosis through di ...

� Do not install the Trueprep™AUTO next to instruments that may cause vibrations or electromagnetic interference. � Do not store the Trueprep™ AUTO in the path of direct sunlight or use it close to any radiating or heating apparatus, such as a conventional oven, hot plate or infrared lamp. � Do not store the Trueprep™ AUTO in an atmosphere of potentially explosive liquids, vapors a ...

� AC Adapter (SMPS) with power cord to power -1No. � (REF603090001)- 25 Nos. Trueprep™ Replaceable tray for cartridge holder � R for cartridge holder Trueprep™ ail guards (10 left hand side and 10 right hand side) (REF603140001) -10 pairs. � (REF603100001) - 1No. Trueprep™ Car ...

� The Power/In Use LED Indicator will glow when the Trueprep™ AUTO is switched on and when it is in use. i) It will glow red and blink continuously when the Trueprep™ AUTO is switched on and waiting for user input ii) It will glow red continuously when it is in use � The Charging/Low Battery LED Indicator will glow when the Trueprep™ AUTO battery is low and when it is being charged using the ...

7.1 Charging/Using the Trueprep™ AUTO with the AC Adapter 7.1.1 Press the Power button to switch on the Trueprep™ AUTO 7.1.2 Low battery � If the battery charge is low, you will see the above alert message � The Charging/Low Battery LED Indicator will glow red and you will also hear a beeping sound. The Trueprep™ AUTO device will not let you begin a run if the battery is low. Fig 4: Low battery LED g ...

7.1.4 Connect the other end of the AC Adapter to a mains socket. 7.1.5 Switch On the mains power. 7.1.6 You can now proceed to use the Trueprep™AUTO using the mains power.If the Trueprep™ AUTO is being charged, the charging LED Indicator will glow blue. Charging takes ~9-10 hours (overnight). When charging is complete, the charging LED Indicator will ...

7.3 Switching ON the Trueprep™ AUTO 7.3.1 Press the Power button to switch on the Trueprep™ AUTO. You will be prompted with the message ‘Buffer Count’. . 7.3.2 Later you will be prompted with the message for 7.4 Placing the Cartridge in the device and starting the run Important: Only use the cartridge provided in the corresponding sample prep kits. 7.4.1 Press the Eject button to open ...

Based Sample Prep Kit Cartridge pack. The pouch also contains one Elute Collection Tube (ECT) for use at the end of extraction. Place the cartridge, after adding pre-treated sample (sample + lysis reagent) into the sample chamber ( see procedure in corresponding Truenat™ pack insert), in the cartridge holder. Note the orientation of the cartrid ...

cartridge stand. Pierce the seal of elute chamber and aspirate out the entire elute into Elute collection tube (ECT) using Disposable transfer pipette provided in the cartridge pack. 7.4.5 Discard the cartridge as per the instructions in Section 8.3. 7.4.6 Tray replacement Cartridge holder contains two rail guards (Left hand side and Right hand side) an ...

8 Errors, Alerts and Maintenance 8.1 Error Messages The Screen displays the error message “Cartridge Not Loaded” Reason: No cartridge is inserted or cartridge orientation is wrong. Solution: Please ensure cartridge is loaded and is in the correct orientation. The Screen displays the error message “VALVE ERROR” Reason: Cartridge valve are damaged. Sol ...

The Screen displays the error message “CARTRIDGE ERROR PRESS EJECT” Reason: There is a leak in the cartridge. Solution: Check for spillage in the tray below the cartridge in the cartridge holder. If necessary, replace the tray (refer 7.4.6). In case the Problem persists contact Molbio support. The Screen displays the error message “RTD ERROR” Reason: The heater is not working. Solution: Contact Molbio Support. ...

Discard the used cartridges, replaceable trays, reagent bottles and other consumables in 0.5% Sodium Hypochlorite. Let the items remain submerged in the solution for 30 minutes and then dispose as per the medical waste guidelines in your region. 8.3.2 Cleaning The surface of the device should be cleaned using freshly prepared 0.5% Sodium Hypochlorite solution and a clean cloth or tissue. This sh ...

MEDICAL ELECTRONIC RUSH DO NOT STACK FRAGILE KEEP DRY Fully automatic operation Rapid sample prepping Mains / rechargeable battery powered AUTO Universal Cartridge Based Sample Prep Kit Portable This Side Up Medical Electronic Rush Do Not Stack Fragile Keep Dry ...

Panaji, North Goa,Goa - 403 722, India. www.molbiodiagnostics.com Molbio Diagnostics Pvt. Ltd. Qarad b.v.b.a. Cipalstraat 3, B-2440 Geel, Belgium EC REP Manufacturing Unit: Plot Nos. M-46/47, Phase III B, Verna Industrial Estate, Verna, Goa - 403 722, India. Email: [email protected] ...