Molift Mover 300 Operator's Manual

BM06101 Molift MOVER 300 English Rev E 24/09/2013 Table of content About Molift Mover 300 .......................3 Before using the patient lifter .................... 3 Explanation of symbols ............................. 3 General safety precautions ..................4 General ..................................................... 4 Lift and transfer ......................................... 4 Assembly and disassembly ..................5 Unpacking ................................................. 5 Assembly ................................................... 5 Disassembly .............................................. 6 Storage .......... ...

BM06101 Molift MOVER 300 English Page 3 of 20 About Molift Mover 300 Molift Mover 300 is a mobile lifter intended for lift- ing and transferring persons to/from bed, floor, chair or similar, wheelchair and toilet. The lift- er is made out of light-weight materials, has cas- tors and is powered by a battery. It has electrically adjustable legs and a lifting capacity of as much as 300 kg (660 lbs). It is therefore ideal for insti- tutional care settings but can also be used in pri- vates homes and nursing homes. The lifter should only be used for transfers across short distances, such as between a chair and a bed or into bath- room/rest ...

BM06101 Molift MOVER 300 English Rev E 24/09/2013 General safety precautions General Before putting a Molift Mover 300 into operation, the operator must ensure that the lifter and acces- sories are in good working order, especially with regards to safety. A Molift Mover 300 shall only be used when all safety devices and equipment is in place and fully operational. The lifter must be taken out of service immediate- ly, or not returned to service, if faults and/or irreg- ularities that may have influence on the safety are discovered. The lifter has an expected lifetime of 10 years or 30 000 lifts with max load (SWL), when all recommended se ...

BM06101 Molift MOVER 300 English Page 5 of 20 Assembly and disassembly Unpacking • The lifter comes in one cardboard box. Verify that the box has no apparent damage. If dam- aged, check the content and contact your deal- er for assistance if components are damaged. • The box contains one complete Molift Mover 300 lifter with hand control, battery and bat- tery charger with mains cable. Assembly • The chassis should be rolled out of the box. • Charge the battery, see page 10. Note! The battery must not be in the battery holder during assembly! • Place the column in the attachment on the chassis, and push the column down as sho ...

BM06101 Molift MOVER 300 English Rev E 24/09/2013 Disassembly • Remove the suspension. • Run the lifting arm all the way down. • Remove the battery to avoid it from falling out during transport. • Release the lock handle on the chassis end re- move the complete column with lifting arm. • Place the hand control on the drive handle. Storage For long time storage it is recommended that the battery is removed and the emergency stop but- ton is activated. The lifter can be stored and trans- ported under the following conditions: Pressure: 70 - 106 kPa Humidity: 15 - 93 % Temperature: -25 - 70 °C The lifter is designed for use at sta ...

BM06101 Molift MOVER 300 English Page 7 of 20 Checklist before use 1. Check that the lifter has no apparent damage or other faults. 2. Ensure that the lifting arm and lifting column are properly fixed and that there are no loose parts on the lifter. 3. Check that the emergency button is deactivat- ed and that the lifter works. 4. Check that you have sufficiently charged bat- teries to complete the task you have planned (no lights on the battery lamps). 5. Check that the service lamp gives a green light indicating it is ready for use. If the service lamp gives a yellow or red light, the lifter needs serv- ice. 6. If faults or irregulari ...

BM06101 Molift MOVER 300 English Rev E 24/09/2013 Lift and transfer The suspension shall always be positioned across the user as shown left in the illustration below. Check that the sling is properly fastened to all four hooks on the suspension to make sure the patient is nor sliding or falling out. Try to position the user as low as possible (prefer- ably resting the feet on the chassis) when transfer- ring the lifter with a suspended user. In this way, the centre of gravity will be as low as possible and therefore reducing the risk of instability. The lifter should be manoeuvred with spread legs in outer position to achieve the highest ...

BM06101 Molift MOVER 300 English Page 9 of 20 Safety devices Molift Mover 300 is equipped with several safety devices, which are intended to prevent damage to personnel and equipment in the case of incorrect use. • The lifter has an overload sensor preventing the lifter to be operated with more than safe working load, 300 kg/660 lbs. If the load ex- ceeds the SWL, the lifter will stop the move- ment. • The lifting arm is hinged to prevent the arm and suspension from squeezing the patient if it is lowered too much. The actuator will not pro- duce any force when moving downwards. • The suspension has safety hooks to prevent the sli ...

BM06101 Molift MOVER 300 English Rev E 24/09/2013 Battery and charger system Battery care and charging Molift Mover 300 is supplied with a battery with a 26,4 V cell unit that is placed in the battery hold- er on the lift. A battery charger is also supplied to be located easily accessible, either stand-alone or mounted on the wall. Connect the charger mains cable to the wall socket when charging the bat- tery. The Charger must be placed or installed in a way that makes it easy to disconnect mains ca- ble plug. Disconnect the charger mains cable plug when the charger is not in use. Take care not to damage the cable Place the battery in the ...

BM06101 Molift MOVER 300 English Page 11 of 20 Technical data Weight, total: Ex. battery and suspension; 36 kg / 79 lbs Chassis: 19 kg / 42 lbs Lifting column: 17 kg / 37 lbs Battery: 1.6 kg / 3.7 lbs Suspension: 3.3 kg / 7.3 lbs Material: Steel, aluminium and composite plastic Motor: Lifting motor/actuator: 24 V DC Leg spreading motor: 12 V DC Battery: Art.no: 1341000 26,4 V NiMH 2,2 Ah, ATO Fuse 20 A Battery charger: Mascot type 2215, 10-22 cells NiCd/NiMH Protection: IP24 Number of lifts with fully charged battery: 50 lifts ( 75 kg / 165 lbs up/down 50 cm / 20 inches) Safe Working Load (SWL): 300 kg / 660 lbs Lifting speed: 27 mm/s ...

BM06101 Molift MOVER 300 English Rev E 24/09/2013 Labelling The main label is placed on the bottom of the col- umn. The control label is placed on the right side of the battery holder Manufacturer Read the user manual Safe Working Load For indoors use Model name Part number and year/week of pro- duction Serial number / barcode Nominal battery voltage Type BF Applied Part Separate waste collection Periodical inspection each 12 month Control lifter accord- ing to checklist on page 18 Designated area for calendar and signed label for periodical inspection READ THE USER MANUAL! Accessories Lifting sling Molift Easy Paediatric Sling Size No he ...

BM06101 Molift MOVER 300 English Page 13 of 20 Molift Easy Toilet Sling Size No head support With head support XXS Part no 3032050 Part no 3033050 XS Part no 3032000 Part no 3033000 S Part no 3032100 Part no 3033100 M Part no 3032200 Part no 3033200 L Part no 3032300 Part no 3033300 XL Part no 3032400 Part no 3033400 XXL Part no 3032500 Part no 3033500 Molift Easy Toilet Sling Comfort Size No head support Separate head support XXS Part no 3016050 Part no 3016055 XS Part no 3016000 Part no 3016001 S Part no 3016100 Part no 3016111 M Part no 3016200 Part no 3016222 L Part no 3016300 Part no 3016333 XL Part no 3016400 Part no 3016444 XXL ...

BM06101 Molift MOVER 300 English Rev E 24/09/2013 Equipment Quick release suspensions Steel suspensions • 4 point steel, Large, size 560x350 mm, Part no: 1430002 • 4 point steel, Medium, size 450x300 mm, Part no: 1430001 • 4 point steel, Small, size 350x240 mm Part no: 1430009 • 2 points steel, Large, size 560 mm, Part no: 1430007 • 2 points steel, Medium, size 450 mm, Part no: 1430006 • 2 points steel, Small, size 350 Part no: 1430008 The suspensions can be used on other Molift lift- ers with the same quick release. If the suspension is mounted on a lifter with lower SWL, the lowest SWL will apply! Castor with direction ...

BM06101 Molift MOVER 300 English Page 15 of 20 Troubleshooting Faults on lifters that do not function as they should after assembly (page 5) or after the check before use has been completed (page 8), can be localized using the troubleshooting table below. Symptom Possible cause/action The lifting column is wobbly The lifting column is not cor- rectly positioned in the chassis or the locking handle is not fully locked / verify position of lift- ing column and locking handle acc. to mounting instructions on page 5. The lifter moves unevenly on a plane surface The castors move unevenly be- cause of pile and dust / clean castors as describ ...

BM06101 Molift MOVER 300 English Rev E 24/09/2013 Maintenance Maintenance of the lifter consists of check be- fore use, cleaning, inspection and service. Check the lifter according to the checklist before use on page 7, to reveal faults or errors. In regularly in- spections of the lifter, which as a minimum should be monthly inspections and annual (periodic) in- spections. Cleaning Detergents must be pH-neutral. Do not use solvents or strong liquids - this may dam- age surfaces on the lifter. For disinfection when needed; use isopropyl alcohol. Avoid abrasive cleaning products. • Clean surfaces with a damp cloth using an ap- propriate ...

BM06101 Molift MOVER 300 English Page 17 of 20 Service Molift Mover 300 has a LED on the battery holder indicating if the lifter needs service. The LED gives a green light when the lifter is ready for use. The electronics logs how much the lifter is being used, and the load it is used with. After a given time of usage there will be given a signal that the lifter needs service to the service LED. The LED will first give a yellow light, then red. Take contact with your local service representative and order serv- ice. If there is a sound together with the light, it means the lifter needs service immediately. Service lamp Status No light ...

BM06101 Molift MOVER 300 English Rev E 24/09/2013 Checklist for periodic inspection 19.05.2011 Lifter serial no.: .............................. ................................. . other ID no. (if any): ....................................................... Client: ............................................. ................................. ..................... .................................................................. Inspection carried out by: (Block capitals) ........................ .............. from .................................................................. Molift certification no. (if any) for inspector ...