Mojotone TMB Manual 

Text of Mojotone TMB Manual 

1X12 COMBO AMP / AMP HEAD

M ojotone’s 18watt TMB Amplifier Kit addresses a common mod made to a classic circuit, but with a few new flavors of our own. The 18watt TMB is based on the circuit used in vintage Marshall models 1958, 1973, and 1974 (more affectionately known as the ‘18-watters’.) These original Marshalls were only produced between the years 1965 and 1967, but were highly sought-after for having massive sounding JTM-45-like tones in a sma

SECTION 1: SAFETY PG.3

SECTION 2: TOOLS PG.3 SECTION 3: PARTS INVENTORY PG.4 SECTION 4: COMPONENT IDENTITY & ORIENTATION PG.5 SECTION 5: CHASSIS ASSEMBLY PG.6 SECTION 6: TRANSFORMER WIRING PG.8 SECTION 7: COMPONENT WIRING PG.10 SECTION 8: BOARD ASSEMBLY & INSTALLATION PG.10 SECTION 9: WIRING THE SOCKETS, JACKS & POTS PG.12 SECTION 10: Rear panel component installation & wiring PG.14 SECTION 11: SPEAKER WIRING & INSTALLATION PG.15 SECTION 12: INI

Mojotone TMB SAFETY FIRST! ELECTRONICS CAN BE DANGEROUS AND MUST BE TREATED WITH RESPECT. ANY CIRCUIT THAT WORKS WITH 120 VAC POWER FROM AN

ELECTRICAL OUTLET IS ESPECIALLY DANGEROUS AND COULD POTENTIALLY KILL YOU. HERE ARE SOME SAFETY GUIDELINES TO KEEP YOU SAFE AS YOU WORK: ½” Nut Driver Set of needle nose pliers (one with no grip and one with serrated edge) Wire Cutters Wire Strippers Soldering Iron & Solder

BUILD. MODIFY. REPAIR.

4 ECC83S EL 84 EZ 81 ECC83S EL 84 EZ 81 ECC83S EL 84 EZ 81 ECC83S EL 84 EZ 81 SECTION 3: PARTS INVENTORY *optional based on order (1) Void Free Birch Combo Cabinet* (1) Mojotone British Vintage 30w, 12“, 8Ω Speaker* (1) British Style 18 Watt Power Transformer (1) British Style 18 Watt Output Transformer (1) Aluminum Chassis (1) Void Free Birch Head Cabinet* (1) Faceplates (front & back)* (1) Turret Board Vacuum Tubes* (3) Impedanc

COMPONENT IDENTITY & ORIENTATION

ENSURE ALL POLARIZED CAPS ARE IN THE CORRECT ORIENTATION WHEN INSTALLING ONTO THE BOARD. THIS IS TYPICALLY DENOTED BY AN ARROW POINTING TOWARDS THE NEGATIVE SIDE, OR A SMALL INDENTION ON THE POSITIVE SIDE. SAFETY FIRST! A CAP IN THE WRONG ORIENTATION CAN EXPLODE! SO FOLLOW YOUR WIRING DIAGRAM AND PAY CLOSE ATTENTION WHEN ORIENTING YOUR POLARIZED CAPS. POLARIZED NON-POLARIZED Carbon Composite S
BUILD. MODIFY. REPAIR. 6 500 K 25 K 250 K 500 K 500 K 1 M 500 K SECTION 5: Chassis ASSEMBLY PLEASE NOTE: ALL PARTS LISTED IN THE CHASSIS PREP SECTION STARTS AT ONE END OF THE CHASSIS AND COMPLETES ON THE OPPOSITE END, BOTH TOP AND BOTTOM. Mount the power transformer using its pre-assembled hardware and your adjust- able wrench. The transformer will be re- cessed through the rectangular cutout in the “belly” of the chassis. Install rubber grommets in ho

The faceplate will be secured by the washers and

nuts from the components being mounted through it. Ensure the faceplate is straight before tightening down the components and installing the knobs. Mount indicator lamp using its pre-assembled hardware. Unthread the hardware from the com- ponent and insert it through the chassis and cor- responding faceplate cut out. Reapply hardware and tighten with adjustable wrench and pliers. Mount you
BUILD. MODIFY. REPAIR. 8 2.7 K 68K 10 K 1M 500 K 25 K 250 K 500 K 500 K 1 M 500 K 1M SECTION 6: TRANSFORMER WIRING Twist all matching pairs of wires coming out of the power transformer. Measure length needed for each wire, allow your- self extra lead and cut to length. This will eliminate excess wire and free up space in your chassis. Apply this principle to all leads. Prepare the two Red wires from the power trans- former (HV secondary). Connect one wire

On the output transformer the Red, Blue and Brown

wires are the primary and the Black, Yellow, Green and Orange are the secondary. Twist the Blue and Brown wires together and run them between the two output sockets. Prepare and connect the Brown wire to the 7 pin of the output tube socket closest to the power transformer. Prepare and connect the Blue wire to the 7 pin of the output tube socket furthest from the power transformer. Prepare
BUILD. MODIFY. REPAIR. 10 SECTION 8: BOARD ASSEMBLY & INSTALLATION SECTION 7: Component wiring SAFETY FIRST! BE SURE TO TAKE NOTE OF POLARIZED CAPACITOR ORIENTATION FOR THE 16UF CAP, AND (2) 25UF CAPS. Begin by applying traces (or “jumper wires”) to the board. PRO Tip: Utilize the different sections on the post of the turret when attaching your wires and compo- nents. This makes for easier soldering and repair. Once jumper wires are in place, follow wi

Mojotone TMB

www.mojotone.com 11 10 nF 10 nF 10 nF 10 nF 4.7 nF 22 nF 22 nF 22 nF 100K 100K 100K 100K 820Ω 820Ω 10K 47K 47K 470K 470K 470K 470K 470K 470K 470K 5.1K 16uF 22 nF 22 nF 680 nF 47 pF 500 pF 500 pF 25uF + 100Ω 100Ω 2.7 K 5.1K 820Ω 100K 100K 2.7 K 130 Ω 25uF + 10 nF 10 nF 4.7 nF 22 nF 22 nF 22 nF 100K 100K 820Ω 820Ω 10K 47K 47K 470K 470K 470K 470K 470K 16uF 22 nF 22 nF 680 nF 500 pF 500 pF 25uF + 2.7 K 820Ω 100K 100K 2.7 K CROSS-SECTION O
BUILD. MODIFY. REPAIR. 12 SECTION 9: WIRING THE SOCKETS, JACKS & POTS Pro Tip: This is a high gain preamp and is more sensitive to filament hum from wiring lead dress. Take care that signal wires are routed away from the filament wirings and previous gain stages. Twist tightly together a length of about 3’ of Red and Black wire to start wiring the tube filaments. Starting with the power tube that is closest to the rectifier tube, prepare and connect the

Prepare the Blue wire and connect

from the can cap mounted between the rectifier tube and power tube, to the turret where the two 100 Ohm 1 watt resistors meet. Prepare the Black wire and con- nect from the grounded lug terminal, mounted by the power transformer, to the turret closest to the front of the chassis where the 130 Ω resistor / 25uf capacitor are mounted. Prepare the Blue and Red wires and connect from the can capaci- tor m
BUILD. MODIFY. REPAIR. 14 PHASE INVERTER 9 PIN SOCKET 12AX7 POWER TUBE 9 PIN SOCKETS EL84 RECTIFIER TUBE 9 PIN SOCKET EL84 CAN CAPACITOR 32µF + 32µF @500V FUSE HOLDER A/C POWER JACK IMPEDANCE SELECTOR J1 SPEAKER JACK J2 SPEAKER JACK 47K 47 pF 10 0Ω 2.7 K 10 K 10 K CAN CAPACITOR 32µF + 32µF @500V FROM INDICATOR LAMP FROM MAINS SWITCH FROM POWER TRANSFORMER FROM OUTPUT TRANSFORMER SPEAKER WIRE HARNESS ASSEMBLY TO GROUND TAB TO GROUND TAB Install rear f

INITIAL CHASSIS TESTING

Starting from the left side of the chassis, ensure all solder joints and connections are good. Physically inspect every tube socket closely, making sure there are not any extra wires touching other pins. Look and listen for loose hardware by shaking chassis. Ensure chassis is free from debris before plugging in. Check for pinched or burnt wire insulation. Adjust lead dress so it is easy to see compone
BUILD. MODIFY. REPAIR. 16 ECC83S ECC83S ECC83S ON BASS MIDDLE TREBLE GAIN TONE VOLUME MASTER INPUTS STANDBY ON MAINS INDICATOR EL 84 EL 84 EZ 81 arcing or smoke from any component or transformer. If you see anything, shut down the amp immediate- ly. Disconnect the amplifier from wall socket, check voltages on the filter capacitors (DC voltage), make sure they are drained, and then recheck your wiring. SAFETY FIRST! THERE ARE NOW HIGH VOLTAGES PRESENT IN TH

CONGRATULATIONS!! YOU HAVE JUST BUILT YOUR VERY OWN MOJOTONE

18WATT TMB. THERE IS ONLY ONE ON THE PLANET THAT IS LIKE YOURS. WE HOPE YOU HAVE ENJOYED THIS EXPERIENCE AND GAINED KNOWLEDGE TO HELP YOU BECOME MORE CONFIDENT TO BUILD MANY MORE AMPS AND SPREAD YOUR KNOWLEDGE. SHARE YOUR BUILD WITH US WE WANT TO SEE YOUR FINISHED AMP. SEND PHOTOS TO: [email protected] OR TAG US!!! @ MOJOTONE @
BUILD. MODIFY. REPAIR. 18 TWEED CHAMP 5F1 STYLE COMBO TWEED DELUXE 5E3 STYLE COMBO MOJOTONE TWEED BASSMAN 5F6-A STYLE COMBO BLACKFACE Princeton REVERB® STYLE COMBO BLACKFACE DELUXE REVERB® STYLE COMBO Mojotone’s Tweed Champ Style Amp Kit is based on the beloved 5 watt amp from the 1950s. These amps were perfect for recording and were featured on a wide array of re- cordings from Joe Walsh’s “Rocky Mountain Way” all the way to Derek & the Dominos

Mojotone Amplifier Owners Instructions: