Orientalmotor EAS Series Operating Manual

This Manual describes product handling procedures and safety precautions. • Please read it thoroughly to ensure safe operation. • Always keep the manual where it is readily available. HL-17168-10 Motorized Linear Slide EAS Series Actuator OPERATING MANUAL 1 Introduction .............................. 2 2 Safety precautions ................... 4 3 Precautions for use ................... 7 4 Preparation ..............................10 5 Installation ...............................15 6 Connection ..............................24 7 Maintenance ............................27 8 Standards, general sp ...

Use the product correctly after thoroughly reading the "2 Safety precautions" on p.4. In addition, be sure to observe the contents described in warning, caution, and note in this manual. The product described in this manual has been designed and manufactured to be incorporated in general industrial equipment. Do not use for any other purpose. Oriental Motor Co., Ltd. is not responsible for any damage caused through failure to observe this warning. 1-2 How to use operating manuals Operating manuals for the EAS Seri ...

These are the lists of the motor model names that are equipped in the EAS Series. The power supply current capacity, accessories and others of the drivers to be combined with the motorized linear slide are described in the OPERATING MANUAL Driver. Since the motor model names are described in the OPERATING MANUAL Driver, check by reference to those described in the tables. � EAS Series equipped with the AZ Series z AC power input type z DC power input type Motorized linear slide model name Motor model name Motorized linear slide model name Motor model name EASM4AZAC AZM46AC EASM2� ...

safe, correct use of the product. Use the product only after carefully reading and fully understanding these instructions. You must not operate the motorized linear slide (operate the equipment for the specified purpose) if the machine in which the motorized linear slide is installed does not satisfy the related safety standards. The factory safety manager or safety personnel in charge of the applicable machine must ensure that the machine is operated only by qualified personnel who are familiar with ...

troubleshooting the motorized linear slide. Failure to do so may result in fire, electric shock, injury or damage to equipment. • Take measures to keep the moving parts in position for vertical operations such as elevator applications. Failure to do so may result in injury or damage to equipment. • Operate the data setter outside the safety cage. Failure to do so may result in injury. • Be sure to provide a safety cage conforming to EN ISO 13857 to prevent persons from entering the moving range of the motorized linear slid ...

Doing so may result in electric shock, injury or damage to equipment. • Keep your fingers and objects out of the openings in the motorized linear slide. Failure to do so may result in fire, electric shock or injury. • Do not touch the motorized linear slide while operating or immediately after stopping. Doing so may result in a skin burn(s). • Do not carry the motorized linear slide by holding its cables or its moving part. Doing so may cause injury. • Keep the area around the motorized linear slide free of combustible materials. Failure to do so may ...

7 3 Precautions for use This chapter covers limitations and requirements the user should consider when using the product. � General z Always use the supplied cable or accessory cable to connect the motorized linear slide and driver. In the following condition, an appropriate accessory cable must be purchased separately. • If a flexible cable is to be used. • If a cable of 3 m (9.8 ft.) or longer is to be used. • If a motorized linear slide and driver package without a cable was purchased. z When conducting the insulation resistance measurement and the dielectric strength test, be sure to separate the connection between th ...

8 � Temperature z Use the motorized linear slide equipped with the AZ Series in conditions where the motor surface temperature will not exceed 80 °C (176 °F). The motor surface temperature may exceed 80 °C (176 °F) under certain conditions (ambient temperature, operating speed, duty cycle, etc.). In order to protect the encoder (ABZO sensor), use the motor in conditions where the surface temperature does not exceed 80 °C (176 °F). If the encoder (ABZO sensor) temperature reaches the upper limit, the motor overheat alarm will generate. z Use the motorized linear slide equipped with the AR Series in conditions where the motor ...

9 z How to fix the cable Fix the cable at the positions near the connector so as to apply no stress on the connector part. Take measures so as to apply no stress on the connector by using wide clamps or by fixing at two places. In the case of the EAS2 type equipped with the AZ Series, fix both end of the cable covering part. Do not fix the lead wires. In the case of a fexible cable, this area is a movable range. Fix Fix In the case of a fexible cable, this area is a movable range. Fix Fix Motorized linear slide � EAS2 � EAS4, EAS6 Driver Driver ...

4-1 Checking the product Verify that the items listed below are included. Report any missing or damaged items to the Oriental Motor sales office from which you purchased the product. When purchasing a motorized linear slide and driver package When purchasing a motorized linear slide only • Motorized linear slide • Driver • OPERATING MANUAL Actuator (this document) • OPERATING MANUAL Driver • Recovery Guide (Supplied with the models equipped with the AZ Series) • APPENDIX UL Standards *1 • Connectors bag • Cable for mo ...

Verify the model number of the purchased product against the number shown on the package label. Check the model number of the motorized linear slide against the number shown on the nameplate. � Motorized linear slide and driver package model z EAS2 E A S 2 N X - F 0 0 5 - A Z A K D - 3 1 2 4 5 6 7 8 9 10 11 12 z EAS4, EAS6 E A S 4 R N X - D 0 2 5 - A Z M K D - 3 1 2 3 4 5 6 7 8 9 10 11 12 1 Series name EAS : EAS series 2 Linear slide size * 2 : Width 40 mm, Height 38 mm (Width 30 mm, Height 38 mm) 4 : Width 58.4 mm, Height 60 mm (Width 45 mm, Height 60 mm) 6 : Width 75.4 mm, Height 83 mm (Width 62 ...

z EASM2 E A S M 2 N X F 0 0 5 A Z A K 1 2 4 5 6 7 8 9 10 z EASM4, EASM6 E A S M 4 R N X D 0 2 5 A Z M K 1 2 3 4 5 6 7 8 9 10 1 Series name EASM : EAS series 2 Linear slide size * 2 : Width 40 mm, Height 38 mm (Width 30 mm, Height 38 mm) 4 : Width 58.4 mm, Height 60 mm (Width 45 mm, Height 60 mm) 6 : Width 75.4 mm, Height 83 mm (Width 62 mm, Height 83 mm) 3 Motor mounting direction R : Parallel motor mounting type (Right side) L : Parallel motor mounting type (Left side) Blank : In-line motor mounting type 4 Sensor mounting rail N : Without sensor mounting rail Blank : With sensor mounting rail 5 Table X : ...

Motor Table Top cover Sensor mounting rail Coupling case Motor Table Top cover Pulley cover Sensor mounting rail � In-line motor mounting type � Parallel motor mounting type � Mechanism of the parallel motor mounting type Motor mounting screws Motor mounting screws Tension adjustment springs *2 Pulley cover Pulley Belt Tension adjustment screws *1 *1 The motor is fixed in the position where the belt tension becomes optimum. *2 Springs for belt tension adjustment are installed. � Motor z Motorized linear slide equipped with the AZ Series Electromagnetic brake cable Electromagnetic brake Motor cable Encoder cable ...

The following figure show models for the electromagnetic brake type and AC power input. Electromagnetic brake cable Motor cable Motor Connector cover Protective Earth Terminal Electromagnetic brake ...

The motorized linear slide has been designed and manufactured to be incorporated in general industrial equipment. Install them in a well-ventilated location that provides easy access for inspection. The location must also satisfy the following conditions: • Inside an enclosure that is installed indoors (provide vent holes) • Operating ambient temperature: 0 to +40 °C [+32 to 104 °F] (non-freezing) • Operating ambient humidity: 85% or less (non-condensing) • Area that is free of explosive atmosphere or toxic gas (such as sulfuric gas) or liquid • Area not exposed to direct sun ...

The motorized linear slide can be installed in any direction. Taking account of vibration prevention as well as deflection of the motorized linear slide, install it on a metal surface of sufficient strength (thickness 10 mm or more). Secure so that the entire area of the bottom face of the motorized linear slide contacts the mounting plate. Install the motorized linear slide so that the cable or encoder does not contact the mounting plate. Mounting plate Mounting screws Positioning pins � Mounting plate The thickness of the mounting plate described in the table is the minimum requirements for ...

Model Screw size Tightening torque Length from the mounting plate EAS2 M4 2.4 N·m (340 oz-in) 4 mm or less EAS4 M5 5 N·m (710 oz-in) 6 mm or less EAS6 M6 5 N·m (710 oz-in) 8 mm or less About the length of mounting screws and positioning pins from the mounting plate, be sure to observe the specified value. Exceeding the specified value may cause the table to break, leading to injury or mechanical damage. Mounting screw Positioning pin Specifed value or less Specifed value or less � When the EAS2 type equipped with the AZ Series is installed in equipment The encoder (ABZO sensor) of the EAS2 type equipped with the ...

When moving the table of the electromagnetic brake type manually, connect the 24 VDC power supply for electromagnetic brake to release the electromagnetic brake. z Specifications of a power supply for electromagnetic brake Model Voltage Current capacity EAS2 24 VDC±5% * 0.05 A or more EAS4 0.08 A or more EAS6 0.25 A or more * If the distance between the motorized linear slide with an electromagnetic brake and the driver is extended to the following length, use a power supply of 24±4% VDC. Motorized linear slide equipped with the AZ Series : 20 m (65.6 ft.) Motorized linear slide equipped with the ...

The motor cable leading direction can be changed according to the space of equipment. • When changing the motor cable leading direction, remove the load, and perform in a state where the motorized linear slide is placed in a horizontal position. Doing the operation in a vertical condition may allow the moving part to fall, leading to injury or mechanical damage. · If the motor mounting screws are removed in a state where the motorized linear slide is installed vertically, the motor may rotate rapidly. Thereby, fingers may be caught in the product or the cable may be disconnected. • S ...

Motor mounting screws (M3, 4 places) Motor mounting screws (M2.5, 2 places) Motor mounting screws (M4, 4 places) EAS6 EAS4 EAS2 3. Change the cable leading direction, and mount the motor. Mount the motor according to the procedure opposite of dismounting it. Refer to the table below for the tightening torque of the coupling fixing screw and motor mounting screw. Model Coupling fixing screw Motor mounting screws Nominal size Tightening torque Nominal size Tightening torque EAS2 M1.6 0.25 N·m (35 oz-in) M2.5 0.5 N·m (71 oz-in) EAS4 M1.6 0.25 N·m (35 oz-in) M3 1 N·m (142 oz- ...